I Full Rapid CRASHED Our HELLER CP6000

[@ryanclarke2161]

Why did it crash?

[@TITANSofCNC]

He ran the entire part above (dry ran)… except for the drill because it was to long. Then he just made a simple error in the program when editing… and then didn’t pause the tool as it approached the material… to double check that it was positioned correctly. Simple mistake that won’t happen again.

[@MakeItWithCalvin]

Hey, it shows it can happen to anyone at any time. Just take steps to mitigate the risk to the best of your ability.

[@ArmoredZephyr]

Looking at it in slow-mo, was the drill spinning the wrong way?

[@barrysetzer]

Haha no, it wasnt spinning the wrong way. But it sure looks like it. Im guessing that shot was mirrored in editing or something like that

[@trainedtiger]

Because the part was in the way.

[@WaukeePaintballer]

If a machinist ever tells you that they've never crashed a machine they're a liar.

[@22jbwest]

I’ve done it twice in sixteen years.

[@josh_1518]

I’ve never crashed one yet… (I’m only 17 only machining I’ve done is on manual machines and only cnc is a small amount of laser cutting and a fair bit of 3d printing

[@mannydiehard1]

💯

[@Anthony-uz5tj]

people in my shop crash all the time the job refuses to update our setup sheets i always tell the guys empty out every tool and if the wrong tool comes out nothing will crash cuz the pocket is empty.

[@therealsourc3]

When I was fresh in the trade I came from using a manual lathe which counts DOC in diametric value, then went to a CNC lathe and was about to do an internal bar cycle. I typed in 4 mm into the DOC row in the program and thought nothing about it. When the cycle started on the boring bar the whole tool just exploded on contact and the machine emergency stop kicked in. That's when I learned that CNC lathes counts DOC in radial units 😅🤷‍♂

[@robertgcode965]

A few years ago we had a bad crash on a big $1.5mil machine. It didn't feel bad at first but the spindle repair bill was around $30k and about a month of downtime.

[@derekschommer1465]

for a 1.5M machine that sounds pretty cheap for a spindle repair

[@derekschommer1465]

cheap ass haas's wanted over 10k for ours

[@lks1441]

​@@derekschommer1465 Well it´s not cheap but compared to other brands HAAS is one of the cheapest on repairs. The company I work for had to replace the spindle on our HAAS VF4 after I destroyed it. I had the machine going while I was getting some more material and when I came back to the machine the tool had been bent out of the spindle, but the machine had not turned off the spindle so it was still spinning which ended up destorying the bottom of the spindle and the bearings. It cost us around $7500 for the repair.

[@greeneyesfromohio4103]

I run an old Makino and the computer board needed replaced….was like $18,000 I was blown away, I don’t see how small machine shops can afford that.

[@pmacamfg7655]

@@greeneyesfromohio4103 eBay and skill, inherent or borrowed (practical machinist), if you think about it, there was probably only one component, or chain of components, on that board that needed replacing. I've had to add an emotional support capacitor to one machine that started acting up, clipped the wire going to a motor overload thermister on another. for me that $18,000 would be spent on 3 replacement CAT 50 machines and rigging.

[@PBSTwo]

Just did the same thing with a 1.375" Sumitomo WDX drill in a Hyundai Wia 650. I was absolutely amazed that only the inserts broke! In my accidental attempt to rapid 11 inches below the top of my part, I made a really cool .5" thick octopus tentacle looking chip. Cool suff!

[@earendall]

I'd like to see the kinematics tests.

[@ffagilar2245]

The crashed looked staged.

[@JamesWatts-ik8fe]

Those kind of crashes are usually followed by - “Well, what had happened was… “, lol! I won’t even say that Heller is an awesome piece of equipment- that’s a work of art! Good stuff!

[@barrysetzer]

Hahaha that was when i went to tell Titan about it 😂

[@gabemoore8119]

That's probably the best sales video for heller I have ever seen. The biggest fear I have in purchasing a large mill like that would be the inevitable crash. Good to see they have some form of remediation to avoid major damage.

[@maxcimander188]

they can't have that fast of a reaction to prevent damage, at least with bearings its pretty much impossible. The Microdent that was made inside the bearing rings / the deformation in the bearing balls means that the service life of those bearings is like 100th of their normal service life. Especially with the impact vector that happened here. My Professor in CNC machining (developed and built cnc 3/5 axis machines in germany for 30 years) said that these crashes happen, but if its a bad one (like in the video), you won't notice it in the first few hours, thinking the machine didn't get hurt. Like a month later, you need to have the spindle serviced, because it won't run properly anymore. Nobody thinks about the crash because noone reports it (at least most of the time) and so the connection between the two is never noticed. Every time you fullrun your spindle directly into the a part with maximum velocity, he said you can schedule a service like a month in the future from that crash. Of course this can be a crash that wasn't that bad, in perspective to the bearing size, but it 100% decreased the service life of the axial load bearings.

[@adammiller4879]

@@maxcimander188I’m sorry, but you’re wrong, this is new technology , every machine has a maximum axial load for machining, your Z axis load, on newer machines even some haas, it’s called crash prevention, you can set a maximum load to alarm the machine out to prevent damage, let’s say the machine takes damage at around 180% z axis load, you can set the machine to come to a dead stop at 100%, this is very common now on most machines.

[@tontonsatan3093]

yes it is very likely indeed@@maxcimander188

[@donniehinske]

It is awesome you guys made this into a video. The fact that machine was just fine still blows my mind

[@rickyhammer6832]

Machine is built to stall and alarm up, that was not a real crash.

[@silverx5733]

Lol if you think they didnt do it on purpose 😂

[@barrysetzer]

I can personally assure all of you, that this was 100% a result of me cancelling my tool length offset. Maybe stupid, but sorry im not perfect. We were collectively impressed that the machine kept trucking, so decided to share it.

[@maxcimander188]

@@barrysetzer hey, just to keep up hows the heller doing from the video? did the spindle have to get replaced already or are you guys still waiting for it to fail?

[@tontonsatan3093]

@@barrysetzer that's actually an incredible feat indeed, I've never seen a machine just shrug off such a hit before.

[@archie3537]

Barry ,did a sonic Boom!

[@st3althyone]

That Heller mill took that crash like a champ. What an amazing machine, not only was it able to protect itself, but recover so quickly as nothing happened. Thanks for showing us what these machines are capable of.

[@SshanIcsS]

As a Hermle operator, the worst message is "Replace spindle head". Then you know that the day is over.

[@B3msprototyping]

See I love that this is a video. Seeing a top tier guy like Barry crash makes it feel real. Everybody makes mistakes, it’s what you learn from them that separates you from everyone else.

[@max_eley]

Intresting, I would like to still see the spindle test bar results, and bearing preload before and after that.

[@aktik6000]

Totaly, I won't belive every word people say to the camera 🤔

[@max_eley]

@@aktik6000 yeah, it is also an axial crash, if it were a radial collision, the machine would be damaged thats for sure, it's unsurprising the axes haven't moved with that type of collision. Not dissing heller, I love them, just saying that's all 😂

[@jasonruch3529]

​@@HoofHearted314😂😂😂newly formed😂😂😂 best comment!

[@MrJohnnyFred]

These guys should really be showing you how to not crash the machine

[@85CEKR]

ya just because the kinematics check out doesn't mean the machine is ok. We had a crash on a machine 10 years ago and is took a few years before all kinds of gremlins started showing up, but they did.

[@jeremymatthies726]

Barry, when Heller says its full stop they weren't kidding. I've never seen a machine crash be it lathe or CNC but that was impressive response.

[@beerzerker8359]

I've had a couple of crashes, but nothing like that. Having rigid setups is probably the most beneficial. I do a lot of weldment machining and trying to get a rigid setup on some of those parts can be a nightmare when you have several surfaces to machine and often a few in one setup.

[@wildin13]

One of my favourite sayings, "If it ain't broke, try harder!" I'm the kind of guy who sale reps hate because if they tell me a tool runs at X, that tool is being tested FIRST TIME at X. No messing around 😂

[@wzpu3283]

Like me, because I go full throttle on a rebuilt engine on the first test drive. Gotta set the piston rings.

[@Soundpost-f2l]

In theory it should run max capacity best at first, before it's had time to wear down a little.

[@vonpredator]

So eh Barry? What was the chipload on that initial plunge? 4” per tooth? 😅

[@barrysetzer]

Bwahahaha fave comment

[@mgk1397]

If the 3,500 IPM he stated is correct, that should have been 5.1852" IPR & 2.5926" per tooth at the 675 rpm shown at 0:55 (Looks like a 2 flute drill to me) Probably just a little over what the manufacturer recommends! 😆

[@왁스바른호랑이]

Safety is paramount. I need to make it a habit to always check before work. I am especially careful when working with large workpieces on large lathes.

[@blockfifteen]

agreed, its easy to become complacent/comfortable and make mistakes. Its especially bad around these potentially deadly machines

[@realJohnLab]

Who left Barry unsupervised in the shop. Fire that guy.

[@barrysetzer]

Yeah they should have known better 😂

[@Engineering_Science]

It was part of the show...

[@dubi127]

this hits close to home, i crashed our 5-axis Leadwell last week, first checks showed the trunion table a bit off, but we still have to call the service techs to come and check it properly... right now its working with around 0,05° offset on A-axis... But hey, before the crash the spindle runout was at 15 microns on 300mm test bar, now its at 5 microns...

[@Andriu_FPV]

Lol so you literally fixed the runout xD

[@dubi127]

@@Andriu_FPV seems like it, but i think i can feel some vibrations from the machine when the spindle is running, maybe it was like that even before my crash, but now i cant really tell...

[@Dammes83]

As a design engineer for heavy duty CNC machines I’m really impressed. To be more precise: A) about your honesty - makes you very trustworthy B) about the durability of this machine. To have almost no crash- impact, although the machine is equipped with a swivel-head. … WOW

[@kentl7228]

Emergency crash detection instantsneous stopping. I wish I had that on ones I use. A bit of piece of mind.

[@piratiniwood547]

... It happens to all of us😉 so many things to think off, and sometimes it is 💩. Back in the saddle and go 😊

[@maxmor3]

Помню как в начале пути уебал DMC60H аналогичным способом - сверло 35 прилетело на ускоренной подаче в деталь. Станок не пострадал, немного сместило угольник, к которому крепилась деталь, а вот сверло знатно перекосоёбило. Но с помощью трубы оно было выставлено по биению до пяти соток, и продолжило работать после замены пластины. Не ошибается тот, кто ничего не делает. Удачи, с наилучшими пожеланиями)

[@davidrabenius726]

I was taught to use single block with reduced rapid speed for the first time running a program. Saved my butt several times as a result. I was at another shop running Lathes and the shop foreman asked me to run a mill job one night. He loaded the program and assumed that everything was ok and hit the green button. All hell broke loose. There was another fixture on the table and it hit so bad that the machine was knocked off its mounting pads, Broke the spindle and messed up the gear box. Cost was $9K to repair and he tried to blame it on me. I was clear across the shop and heard the building shudder and thought that's going to be expensive. The owner came up to me and asked who did it. He knew who did it but asked to confirm it, makes your you know what pucker up a tad!!

[@skaelring-xj3gq]

Happens to the best of us. I witnessed a 30+year programmer crash a Haas EC-1600 at full rapid. Plowed a solid carbide boring bar into a tombstone. While trying to square away the Mastercam post for a Doosan multi-axis lathe, our lead guy buried a .5 inch diameter end mill into the workpiece twice within two hours. I once crashed the upper turret of the same machine into the main spindle while trying to sync the upper and lower turret programs (in my defense, the arrow down key on the PLC was loose and had a tendency to double-hit). Fortunately, it was only an $800 service call, no major damage. Also saw an ordinarily badass programmer cause approximately $25k damage to a Mazak integrex with one simple error. Moral of the story: don't beat yourself up.

[@esavage8855]

There was one time at my last job where a guy crashed a DMG mori at 100% rapid with a 4in face mill in the spindle. It was a horizontal so the pallet was tilted way back and the spindle was cracked all the way down the side and was melted on the inside. It ended up costing the company $50,000 to fix because it messed up multiple axis the spindle had to be completely rebuilt and the glass was completely shattered

[@barrysetzer]

Jeeeez thats brutal!

[@esavage8855]

@@barrysetzer yeah! I was standing right next to the machine. The feeling of the ground shaking was insane! The guy was doing a setup for production parts and he turned block delete on and it was programmed wrong and had the wrong pallet in and bam!

[@jordanhillis1315]

Did this on small scale last week with a Harvey end mill into my vice. The end mill is okay. The vice has a hole in it now 😭😂

[@barrysetzer]

Its for coolant evacuation 😂

[@msheaver]

For us fans who will likely never darken the inside of a machine shop, please do an AAR (after action report used after a disaster recovery incident) video to discuss in detail what caused this crash. Even though you didn't hurt the machine or the part, that crash was still scary due to the forces involved.

[@ericsandberg3167]

And this is why I always have my finger over the feed hold button whenever I'm working with new Gcode. There are so many steps along the way where you can screw up.

[@KlusekPospolity]

3:40 what the hell is that clamping hahaha :D

[@Hybrid869]

Welp, the machine responded great to the crash. Barry you showed us Hammer Time

[@barrysetzer]

Hahaha, i love that they threw a few of my other crashes at the end. Thanks editor!

[@Hybrid869]

@@barrysetzer hahaha you knew they were gunna. When they got it on cam you know their gunna use eventually. Keep up the great work and stay safe

[@stefanmerk5750]

Booom - Silens - ohhhh - you got me I know this feelings 😂👍

[@Didjin]

I've hade 2 serious crashed. The first one i did what i was told dispite i didn't like the idea.. but i was in the beginning of my career so i obeyed. Almost lost my life.. the second one totally my fault, full speed bouth axis with a 52 mm drill from -20 mm inside hole out to tool change position. After that i did some changes in my rutins and never jump over a step.. sins then I've hade a blast. Excuse my bad eng.. I'm from Sweden.

[@Todestelzer]

When I did this to a Heidenhein the ceramic bearing of the spindle had to be switched out…. Did set Z0 below the part.

[@Zero-cv3pw]

Nice. When our okumas lathes crash they almost need a full rebuild. Multus was crashed and took 2 weeks from tech to pull everything out and back in. Wish they had better quick stop

[@juliopasalodos7214]

I work with mazak machines and I have also had some strong blows in G0, the truth is that they have all withstood without the slightest problem or misalignment, the horizontal machines from my experience are much more robust, the heller tool change seems quite enough to me slow I have noticed that it changes tools slowly my mazak with double contact bt40 changes tools in less than 3 seconds iit's scary

[@whatDIDheSAAYYYYY]

agreed, mazak tool changes are insane! you use gcode or mazatrol??

[@kristiankautto7616]

thats a hsk 100 though,heavier tools

[@Stephen8454]

As a self-taught and still a total noob to the field of machining I appreciate seeing the crashes. Makes me feel less stupid 😅

[@matthewperry8057]

I accidently crashed one of our gantry routers a few days ago. I spent about 20 minutes squaring the gantry, but I didn't know that another tech had overrode the soft limits. A tool change attempt led to a gentle knock, and then I had to square it up and resync the motors all over again....

[@rpatrick2]

I wish you showed how you checked it out. I'm trying to convince my boss to standardize this.

[@barrysetzer]

Maybe we will do a video on it!

[@whatDIDheSAAYYYYY]

@@barrysetzer YES PLEASE! i think that would have been the most interesting part of the video! everyone knows how to crash.... not everyone knows how to check all required checks, after the crash.

[@guebay-k5y]

Die Kontrolle zu zeigen ist schon wichtig. Ist das Teil nur für Showzwecke oder muss es verkauft werden. Bei Kundenteil geht es ja so weiter. Teil abspannen, Maschine kontrollieren, Teil aufspannen, wieder ausrichten, Neu starten. Das zu sehen wäre für mich interessant. Gekräscht hat schon ein jeder CNC Bediener.

[@GeorgiMirov]

I have a DMU Evo 60 , I did what you did too a few times, the machine protection controls stops it in miliseconds. No damage at all , runs as new.

[@rnbspowa7of69]

Thank you. 👍💙😎

[@mesikamoto]

I have the same feature on my 30 year old Okuma. Its just built so damn tough it can take full rapid crashes. After a crash, I put a piece of wood between the turret and ram the machine in the opposite direction to straighten it out. Dial it in and back to machining again.

[@norsktoolmaker88]

Ahh yes, the old, "rapid to crunch" Had it happen once on a Warner Swaysey 2SCL. Makes you mad enough to spit.

[@Rouven-t3e]

I've caused a crash because I forgot to load the right coordinate system and instead of prepositioning my spinning carbide end mill at 5mm above the workpiece, it caused a collision faster than i could react. I have kept the shattered end mill and the scraped part mand made a "trophy" out of it. I've milled a hole for the end mill, right next to the impact point where the shattered tool now sits and i've engraved "Memento Mori" into it. It lives on my desk as a constant reminder to double check the program aswell as things like coordinates before full sending a program.

[@roronoazoro9228]

Similar thing happened to me on Hurco on 100% rapid rate. I was lucky after 1 year it still runs as before crash :)

[@dantwaites7097]

My 1st day running a horizontal mill, i entered the wrong g code on a b axis movement and sent a 2.5" carbide drill rapid travel into the side of the part and broke a bunch of stuff. Needless to say that was my last time ever running a cnc machine.

[@antprzy]

Okay the 12 milion lines of code made me crack. :D I am in machinist school and programs longer than 5-6k lines are impossible. And you wanna do 12 milion with such enthusiasm . I love it

[@hauntycz5191]

Ayo what happend ? Nah just crashed the heller again.. still nothing ? Nah still straight ! Love it

[@CHPU_CNC_NOVICHOK]

Да,это лучшее видео из всех последних!

[@ronjohnson9032]

I crashed a very large bridge mill in the same fashion. Had to change out some 1/4 20 screws and was as good as new. Tough old machine had a fail-safe.

[@randydewees7338]

Very fun vid, thanks! From the ultra-precision side (SPDT), a crash usually meant a $1500 diamond tool just went bye bye. On my optical generators (fancy 5 axis machines), a crash usually just meant referencing the axes as the fast traverses just weren't all that fast. But everything would be off a few microns or a few thou deg. Usually the optical blank went bye bye.

[@filippomontevecchi8618]

I don't know what the heller kinematic test is actually measuring. Assuming that it's like the DMG Mori one, where the machine detects the position of rotary axes pivot, i would recommend to check the backlash of z axis as well. It's just a suggestion, not a criticism!

[@kiurtosh]

Keep on truckin' :))

[@b2dmastersniper]

my worst crash was sending a 3/4 mill about 3" long into the side of my 4th axis. Thankfully it just destroyed my soft jaws before the end mill snapped. Didnt enjoy replacing that $250 cutter though.

[@northwesttiger2060]

Smashed up my first machine this week, a year into my CNC career about £30,000 so far and counting

[@AABB-px8lc]

hmm feedback loop is so fast. How did exactly they make it ? some very close to each other placed sensors and servo logic device with analog trickery like PLL?

[@wendull811]

There are only two cnc machinists types in this world. Those who have crashed them and those who are going to crash them. If you never made a scrapped part or crashed a machine you are either new to the trade or are not working fast or hard enough.

[@Panzermuh]

3:46 What the hell happened there that it bent the side panel of the fixture table? I cannot even make out what it ran into...

[@barrysetzer]

Bwahahaha, it was the tombstone into the spindle. Needed a PLC change

[@efraincaballero7482]

Hey guys, could you share your tips (or process if you have it) on what specific steps do you make to avoid crashes? I'm still a job shop and altough I've never crashed my machine badly, I've broken a few end mills

[@barrysetzer]

Hey Efrain, hit me up on facebook or discord. Ill give you my take.

[@barrysetzer]

Of course, my response should be suspect, as i literally just crashed a machine in front of 100,000 people 😂

[@Tombstone2U]

Are there more videos coming on this part?

[@evanlowe9310]

Gotta get some more crash videos! Love it

[@tdg911]

All Heller machines handle a crash like that? It’s one thing to crash my Tormach with 2hp. I couldn’t imagine crashing a machine with enough hp to begin eating itself.... Funny how when writing software you hit the compile button and if there is an error no big deal or program fails to compile. I had to relearn this when I got into Cnc machining because an error could be catastrophic. Much love and gratitude for the content.

[@michaelapel9810]

Well, a colleage of mine crashed a H5000 straight into the fixture because he selected the wrong program from our robot automation he was setting up. The motor spindle was out of whack by 0.02mm afterwards although it had 8 years of full 3-shift production on it's belt at that point already. So it was not exactly clear if all of that came from the crash. Tool and part of the hydraulic fixturing were also broken. The rest of the machine was fine. Total cost of that crash was around 30k.

[@tdg911]

@@michaelapel9810 That's nuts. Total cost of the machine before tooling?

[@spencerkleiman5035]

At my job writing just got a new doosan?? (Spelling) it's got that sideways puma looking logo on it. I've a machinist in training I've been working for 4 or 5 months so I'm still a rookie, but they said that machine was between 1.7 and 2.5 million dollars. I can't remember exactly I think it was 2.3m so I'm giving leeway each way. We have cheaper machines that don't do the .0010 tolerance as well so we run parts with a. 0030 variance on them and they are our bread and butter. I .are parts for the aerospace industry most of what I personally touch is 99% aluminum. The smaller machines will make certain fittings or pieces out of steel for higher stress/worked areas of the part like clamps ect.

[@michaelapel9810]

@@tdg911 Not quite sure. We only did a retrofit (new PLC and software) on the existing automation on that particular project. My guess would be around 1.8 million for the machine, tooling, fixturing, automation and in line measuring. But who knows what our customer pays for a new Heller. They have around 30 of them by now.

[@tdg911]

@@michaelapel9810 damn….

[@MarcoCollard]

First time choice the probe ... T01 or T02 ? And play with y and x and z- on G00 on same time

[@goldenmath4091]

Yayyy not fired....funny I would still get a good telling off tho : )

[@Engineering_Science]

I was getting ready to see him getting fired... it ended up showing why he still got a job.

[@ciscohernandez4384]

how do you perform a kinematics test?

[@jsihavealotofplaylists]

Thanks for showing your crashes

[@grugbug4313]

Solid! Top KEK! Peace be with you.

[@Hydrazine1000]

_"I hope you like my crash."_ No, I don't ever want to see _your_ crash. But the machine crash you _caused to happen_ was informative!

[@mfatihgur]

I felt that over the internet. No joke. 0:26

[@MrChevelle83]

the huge lathes i run can take a crash pretty much like a train derailment! ive crashed a few times and other employees combined have destroyed $10s of 1000s worth of tooling and absolutely no damage to the machine. id call my self a liar if id not witnessed it over the last 8+ years. Early 1970s built ROMi. lathes they are absolute brutes of machines. the servos will crush the tool (insert) holders and not even flinch.

[@HT-he8gl]

どれだけ優れたmachinistでも機械をクラッシュさせるリスクは0ではありません。 もし間違えないと思っているならばそれは過剰な自信です。常にリスクは付きまとう。

[@strongback6550]

Correct

[@pr00009]

very true man. there is always a room for error. and hence mistakes must not be taken seriously. infact they must be allowed to be corrected promptly

[@HT-he8gl]

@@pr00009 あなたの言う通りです。自分を責めたり、間違えた人を責めることは良くありません。

[@rprice7670]

I dont believe the show would be the same with out you Berry lmao. Ok Titan it is time to put Berry in time out 😂

[@carlnapp4412]

What about the spindle bearings after the crash?

[@tubbytimmy8287]

I'm sure Jessie will remind us of this in his next 8 videos 😊

[@barrysetzer]

No kidding 😂😂😂

[@dylansmith7433]

Does the drill in reverse help the intentional crash?

[@paulmalinoski5951]

I don't believe the drill is in reverse. Look at the moment the drill stops in the material. The momentum looks to be a forward rotation momentum. I think it's just the frame rate messing with perception

[@pmacamfg7655]

Good eye, I guess you don't damage the inserts that way.

[@dirtboy896]

I crashed a Daewoo DMV3016 onto a hard jaw at 50% rapid and it scared everyone in the shop 😂

[@Der_Gallier]

From what I seen so far hermle mashin's are very similar to thisbut got higher acceleration so there is no chance they can detect that at that speed one thing they got tho are aluminum bushings so in lots of cases they take the hit so you don't have to replace the complete spindle just the head

[@kristiankautto7616]

i have crashed 3 or 4 of them,the bushings saved me every time

[@Der_Gallier]

@@kristiankautto7616 i haven't so far but the Maschinist before me has and got saved by those. Really great mashine

[@BogdanS92]

ok, now we need to see a fail compilation

[@barrysetzer]

Well at least there was a mini compilation at the end of this video 😂

[@BogdanS92]

@@barrysetzer MOREEE!!! i want to see you FAIL😆

[@nonamenoface8828]

It's easier than it seems, need only a "-" instead of "+"

[@wendull811]

Or miss the "."

[@TC_Leader_HELLER_US]

This is a really cool video, and shows that something like this can happen to everyone, so please be careful guy's 🙂

[@loupitou06fl]

Your heller need to talk to my tormach and start a support group for abused and crashed CNCs

[@Kardos55]

WOW! That is crazy!

[@FiglioBastardo]

Y'all need to get a hold of the Meltio M450 and put it in one of the hellers.

[@chrisw7188]

just out of curiosity, how much is that heller machine?

[@ArthurDumesnil]

Even the best of the best crash,anyone that runs cnc and says they never crashed,they r lying or it’s never their fault

[@boldlyspokennoah307]

Well that was bad ass

[@jasondk5127]

Distance to go?

[@kylekarsten721]

This is why machinist tool carts have wheels on them... just in case. That being said, I've banged up a few machines over the years and was never let go over it. I work for a good company.

[@DangaRanga]

We'll revisit this in 6-8 months if you still have the machine when the spindle bearings fail. Axial crashes are the least worst way to crash, but still hard on the machine and typically dent the bearings in the spindle which leads to long term fretting and spindle failure. Crashes do and will happen again. name of the game in this world. Willing to bet either wrong work coordinate or wrong tool length offset was called. classic oopsie lol

[@rs2024-s4u]

Holy Crap!!

[@zacharycaron4834]

I’d like to see what I like to call a “new guy crash”. Somehow they manage do get the machine to crash in the most spectacular ways. Rather than an intentional crash. And ya if any machinists ever says they’ve never crashed a machine. They’re full of shit and probably not worth taking advice from

[@Netbug]

I ran 4 machines and crashed 4 machines. The secret is doing it a different way each time.

[@davidmcdonald9171]

Has this machine crash protection ?

[@macresco1]

3:56 That guy in the window doesn't even react while the other guy said he felt it through the floor. Something's fishy here

[@mitchellholroyd2837]

I crashed a Dawoo and the whole machine buckled. It was done. Wasn't my fault. Lost main feed input. Rapid into the spinny thing

[@MeDieValUKRAINE]

MORE CRASH VIDS ! :}

[@D.r8]

How can I contact you because I want to ask you about this machine?

[@barrysetzer]

You can talk to us on our Discord server or Facebook group

[@MK-yq3up]

All cnc crashes make me sick.. even if it's someone other crashes, i dont like watch this kind of video, i made exeptions for Barry ;)