I made a 3D Printed F1 Car (100 Km/h ?)| Part 1/3

Рет қаралды 4,153

Ай бұрын

Hi guys, welcome back to my channel. It's Lee again, Today we gonna make a 3D-printed F1 Car with a brushless motor. This video is quite long so I will divide it into 3 parts. This video is part one, In Part two I will assemble the RX and Tx, and in Part three I will test it outside. So if you feel a little bit interested in this project. Please subscribe to my channel for the next videos coming up. Thanks a lot for watching the video.
3D files for Print : cults3d.com/en/3d-model/gadge...
For Part 2 : • 3D PRINTED RC CAR AT S...
Parts list for anyone who wants to make it.
MC6C mini TX AND RX:amzn.to/3JgCYRF
Brushless motor: amzn.to/3JfZz0y
ESC 40A for Brushless motor: amzn.to/3UhIs4Y
65 mm Wheels :amzn.to/4b0s6ne
Hex Coupler 4mm : Hex Coupler 4mm
S90G servo : amzn.to/3PYoVDW
Shaft Ø4x150 :amzn.to/3Q1FHly
Printer I used:amzn.to/3vC5dqD
M3x45 :amzn.to/3TPZzcA
3S Battery:amzn.to/3JkDFcs
M3x15 and nuts:amzn.to/3vR982T
F604zz bearing:amzn.to/3W0lPmU
-------------------------------------------------------------------------------------------------------------
keyword: Rc car, how to make RC car, DIY rc car, 3d printed RC car, homemade RC car, brushless motor project

Пікірлер: 25

@thygate Ай бұрын

Without a differential I suspect it will run into the curb after only a few meters when getting up to speed. And unless you find some perfect surface, suspension might not be optional either to get up to that speed.. So I suspect the next video part will have some upgrades ;)

@LeeCuriosity Ай бұрын

Thanks for your comment. As I said that I don't have any experience before making this one so It's a little bit frustrating. But Learning is a process, We fail and We learn from it. I hope that some of my projects in the future would be better with you recommendations. I will test it soon so stay tune :))

@Adityasaurus 14 күн бұрын

All your videos are great. You deserve a lot more subscribers. I'd love to see some boat projects too

@LeeCuriosity 14 күн бұрын

I'll make it in the future

@LeeCuriosity Ай бұрын

Any thoughts about this project ?

@tech_projects6743 Ай бұрын

Nice job Lee! As always :)

@LeeCuriosity Ай бұрын

Thanks bro :))

@Luigitel180 20 күн бұрын

I have another question, did your bearings and shaft fit perfectly at the first time? because I ordered 4mm shaft and 4mm bearings and seem they are not fitting properly :/ Or you had to try different producers for the "right" fit?

@LeeCuriosity 19 күн бұрын

I used sandpaper to make the shaft smaller so it can fit to the bearing

@Luigitel180 19 күн бұрын

@@LeeCuriosityah! That makes sense, thanks for the tip

@xuanphuongdinh5395 Ай бұрын

Good job guys

@LeeCuriosity Ай бұрын

@Luigitel180 Ай бұрын

Hi, does the STL file with the parts will be available so I can do it at home too? or this is just to show how it is done and encourage other people to come up with their own designs?

@LeeCuriosity Ай бұрын

Actually all the files will be available on my cults :))

@Luigitel180 Ай бұрын

@@LeeCuriosity yaaay! Can't wait for it then! I already ordered the other parts and was thinking into use the video to reproduce it but it's easier if it's already available :)