I WAS A BIT LATE!! TIME TO WORK ON THE JOHN DEERE X750

Repair and restoration videos returning very soon! Servicing the John Deere X750 ride on mower. It's reached 200 hours

[@morgankennedy9823]

A tip for blowing out air filters always blow the opposite way of airflow. Otherwise youre just pushing the dirt farther in.

[@cheesekakememes]

Yep

[@Kroooza]

Nope, I've been able to get more dirt out by switching between the inside and outside

[@aserta]

At least for the aspect of cleaning up the caked grass, you should build yourself two ramps so you can scoot the mower on them and clean without removing the deck.

[@paulf2529]

No need you can just use the wash port after each use. You connect the water up, set the deck to the lowest setting, engage the blades and lower the deck. I run mine for a bout 3 mins till I see the clippings flowing out. Without cleaning the deck each use the multching is very poor.

[@jameshedrick605]

I take mine off just so i can clean and paint it

[@robertmailhos8159]

Better late than never on lawn mower maintenance glad you are doing this for the piece of mind

[@seggonscontractors588]

I find when I'm washing my agricultural machinery that the grass stain or any other sort of staining comes off really well with a traffic film remover from Kramp, you can put it in a weed sprayer diluted 3 to one and just spray it on, leave it for 5 mins wash it off with the pressure washer and it leave a protective film for the next time you wash it, highly recommended! 25 litre tub is around the £35 mark, you should look into it 😊

[@austinc4013]

Always blow the filters in the opposite direction of flow. It damages the filters by pushing the dirt the filter caught through the filter medium, when you blow it the other way it does not damage the filter as bad.

[@davidfist7801]

I have found that a belt sander (a table model) works great for sharpening blades. It doesn't get the metal too hot, and works really well.

[@923Be]

Great job! Take the other plug out of that oilpan for smooth flow into the pan withouf spillage or burping.

[@weathermannax416]

I have the John Deere X350 with 18 HP Kawasaki V-Twin engine. I had mine since January 2016, and it has 283.5 hours on it. Mine is a four-season machine. I use it to mow the lawns in both my property & my neighbor's property. Then I bag-up the fallen leaves in both my property & my neighbor's. And I plow snow out the driveways. So, I got mine with all attachments at the same time, bagger, plow, weights, chains and Snow Cab. So far it has been a VERY reliable machine without ANY issues and no, I have not replaced the 12-volt battery yet.

[@Adventure_Van_Upgrades]

i have been digging through your archive of restoration work on the huge array of vintage machines and i have to say, you are a man of true dedication to detail. a pleasure to watch and always something to learn from your work ! keep at it , top quality job every time.

[@steamboatwillie935]

Beast of a mower. Itty, bitty mowing deck. Tractor's a bit overkill !

[@patjohnson3100]

Very good maintenance work. This lawn tractor looks almost new. I like the idea of recording the hours and date the oil was changed on the base of the filter. I enjoy this channel.

[@paulosborne6517]

Your videos are so relaxing... I've always though that there is something therapeutic about cutting grass, turns out that mover maintenance is quite satisfying also.

[@johnbradford9235]

Thank you Mr. Machinery Restorer, you helped me to sleep today when I badly needed it 🙏. It's the voice you see. You have a great voice and a brilliant vocal manner for this KZbin malarkey. And yes, I did make sure to re-watch the bits I missed 😉👉. I wouldn't skip one of your vids for the world dude 👊👊👊. 😎

[@vinceianni4026]

Good job mister well done

[@MarkMeadows90]

Thanks for the upload, MR. You always do amazing work! I have never ridden on a John Deere diesel lawnmower before. My dad has always owned petrol powered lawnmowers for most of my younger life up until now. He's had an old Lowe's brand lawnmower from 1989 up until 2002. He sold it to someone who wanted to restore the lawnmower. He bought a Huskee brand lawnmower in 2002 from Tractor Supply Company. He still has that lawnmower in his garage, but the rear axle is broken. He doesn't want to fool around with it, because replacing the rear axle is expensive. His current lawnmower that he owns now is a Toro brand zero turn with a Kawasaki v twin that he bought in 2013. I'm not big on zero turn lawnmowers. I have to have a steering wheel in front of me lol

[@robbone1189]

I’ve just had a new toothed timing belt on a John Deere mower deck, £138 rrp, £38 from our local bearings & belts supplier! I always use original parts, but that’s too big a saving to miss!!

[@BrianMcNeese]

I have found it to be very helpful to clean my lawnmower deck at the end of the mowing season and applying a heavy coat of a mixture of ATF, PB blaster and dish soap. Let it sit over winter, and reapply 2 weeks in the spring before mowing. During the course of the summer I have very little grass accumulation.

[@M.TTT.]

interesting, I wouldn't think they'd all mix well. Mow wet grass?

[@BrianMcNeese]

@@M.TTT. I do on occasion mow wet grass. I also mow 5 and 1/2 acres. I do a midsummer blade sharpening and usually only clean out a couple of handfuls of grass. The ATF and PB blaster have heavy rust inhibitors and the dish soap helps it stick, and it mixes very well. The key is the fall application and letting it soak into the metal all winter. If nothing else, a good preservative for your mower deck.

[@LewisMowersandBoats]

Great job brother 👏

[@warrenvalentino5763]

Great video! Awesome project! i Love watching your videos. keep up the Awesome work! :)

[@henriknordeng]

I got that same makita and i have not regret that buy one bit yet.

[@ShogunMura]

Love that you take care of it and use it. Hope you're doing well!

[@MajorMarch1978]

Been watching your channel for ages now and love your dedication to repairing restoring modern and vintage mowers of all kinds. Surprised to see none of the mowers ive seen the tractor one's have any grass collection. Maybe ibe missed vids with tractors with a grass collector but be interesting to see some with. My Uncle had a Actco lawn tractor he used in Halifax and that was a dream to ride, maintain. Love the channel. Looking fwd to future vids. Richard Perth western Australia

[@minasaluna8618]

More Power to your Channel . ❤ 🥳 🥰

[@mike.4277]

Fantastic video 😎👍

[@liljoeii6091]

Thank you for the video

[@fredhart7904]

You are a braver man than me power washing that wonderful mower, I would just use air pressure and blow off the debris and scrape the dead grass, You blow water into those bearings in a few months or less bearings will start going down Just my humble opinion,

[@Mark-zz9rt]

Flapper disk for the blade’s work great 👍

[@aghistorian763]

At our shop we used to have a magnetic, horizontally free spinning mount which you could attach the blade to. It would turn the direction where the blade was still heavier, really nice little gadget

[@MrNomadnero]

I need to do a few jobs on my ride on, I have been putting them off for a while. You've given me the motivation to at least look at it this weekend.

[@jameshedrick605]

I do the same to mine every year. Just did the same to my push mowers

[@tinkeringtaylor3053]

Excellent video 👌👌

[@AndrewHCann]

Excellent video Machinery Restore :) have work on Lawn Mower Tractor brand called Troy Built red and black color! They used there own motor type and great machine I have 2021 year one ! Very good so far and lots model of them out there !

[@nicbotley1602]

If it’s the same as older JD decks there is a 90 degree offset pin hole so the wheels can be set sideways for pulling the deck out from underneath.

[@kuntryhd1313]

Just got done rebuilding my first push mower

[@quadrapoint]

A really good product for cleaning is TFR as used for cleaning commercial vehicles get the non caustic version. You say you would like a iseki take a look at the shibaura, they were also badged Ford and ransomes. 48" deck shaft drive excellent machines still made today bit pricey new very interesting history

[@darrenashley126]

Here in rural Victoria Australia, I bought a Reco ride on that looked ok. The belt let go 30min in on my first cut. Thinking I pushed too hard I bought new belts and one let go in 15min. I lifted it up with a block and tackle and found the deck bearings to be shot and the mower professional refused to help me out. I ended up selling it for half what I paid and told the guy what needed to be done. I am disabled and couldn't do it myself. This is a warning for people to not just take a pro's word that it is all Reco'd.

[@M.TTT.]

that's unfortunate, you do need to know how to check everything over when buying used equipment - just like cars - otherwise there's lots of dishonest people out there.

[@ridethroughlifertl]

17:47 I tie a loop of paracord around the end of springs, in a bowline, then use the rest of the hank of cord to pull the spring loose. It works with very stiff springs, like on exhaust manifolds and motorcycle kickstands.

[@jasontackett2418]

For putting the PTO shaft back on if you lock the collar back you can pretty easily put the shaft back on reaching from the back on the machine and pulling it forward toward you and sliding it on the splines…pretty easy to feel where they are since you can see them and no taking off the tire.

[@NowInAus]

Thanks for your effort. Looking forward to your next restoration video as this wasn’t the most satisfying tbh. Shocked at that belt price. Ouch

[@ABD5667]

I try to keep my lawnmower cleaned after each use. It's either dry and dusty or damp where I live.

[@johanstahl5555]

I wonder what happend with your restorations and at last here you are!👍🏻😃

[@GWN_Garage]

Always good to see another guy who misses the service intervals 😅 Curious, that electrical plug at 24:00 What has been bypassed? Cheers! 👍🇨🇦

[@firenado4295]

no idea but my mower has the same, its a gx355d and I have a feeling its something to do with an accessory/ attachment.

[@jonnymotoritz4393]

Hello i always enjoy your Videos. for grass stains i use Stihl Varioclean. NEVER Grease fittings before wiping them clean

[@ryanmckinty4457]

Here just something. I found out and it will help u I used to paint all my machinery with used engine oil but then I stopped and started using used hydraulic or back end oil engine oil is Completly full of carbon and the carbon eats away at the metal I’ve seen the damage it’s done on harvesters and stuff and the back end oil is clear and far cleaner to work with

[@aaronobrien7649]

I only re watched your video on daggerwin extra servicing this machine the last time today what a coincidence

[@BentAnvilNZ]

If you rotate the anti-scalp wheels 90⁰ before dropping the deck, it makes it really easy to slide the deck out.

[@terryl7874]

Having a drive transmission shaft instead of belt driven is a good idea.

[@steamboatwillie935]

Yes, it is much more reliable. But cost 4 times as much to repair. When it does fail. The deck still has a belt to run the blades. The shaft is just the drive system. The drive gearbox on the deck is over $400.

[@M.TTT.]

@@steamboatwillie935 exactly, I never really saw the point in them using the shaft pto for a mower deck other than to make more money off parts or maybe for design purposes perhaps.

[@steamboatwillie935]

@@M.TTT.Having had both tractors, will belts and tractors with gearboxes. I'd take the gearbox, over belt driven, any day of the week. Changing belts gets expensive too. I've never had to change a shaft driven gearbox. Hope I never have to.

[@DC_PRL]

for the deck, flip that deck up and dump some used motor oil on it. I don't like painting, rocks will hit the paint, blister and hold moisture

[@zlatkovujevic7348]

Man that new oil is so dark, it looks like W5 engine oil from Lidl.

[@samuelfellows6923]

One thing you didn’t point out that the mower deck on that tractor mower has a male hose connector on the right-hand side of the mower deck = that I assume is for “deluxe” water washing of the deck/blades - after mowing the lawn go to your hose pipe and connect it to the “wash port” and turn on the tap & lower the deck and engage the blades = the mower should clean itself with the water. Another commenter said that, and painting the deck risks blocking the water port?

[@simontravis7452]

Can i ask what you use to paint the deck with, show's we are the same late on service intervals 🙂

[@michaelblaszkiewicz7283]

Can you get a belly mower or a finishing mower for you Kubota? Seems like a better machine than the 750.

[@paulbowers7343]

Put some anti-sieze compound on your blade bolts!

[@NoPegs]

Better late than never I suppose. :3

[@mikespain8655]

Raise mower up for sharpening blades, scrapping deck. No need to remove deck.

[@Bass.Player]

Belt was toast! good only for the trash

[@Carcrafter7165]

👍

[@firenado4295]

man John deere really spoils you with the build quality these days. PTO shaft and not a belt, a proper belt cover for the deck, a diff lock (probably what I'm most jealous of) and also shaft driven transaxel too. our gx355d has only has lone service like this about 20 years ago and its struggling now. all the belts and baring need replaced blates are so warn lines are left in the lawn where its just cut. I cant even remove the belt covers because the bolts just spin in their holes. Also, side note the deck wheels rotate 90* and then the deck roles out easy. Thats all I can remember from the manual some one uploaded online before the website was taken down. we never got a manual or a key with ours, it was all lost in shipping.

[@aidenlarabee1208]

I didn't know daggerwin had a second chanel

[@takis12345]

💯💯💯💯💯💯💯💯💯💯

[@nicolaslab1814]

At Least it is done now.

[@Irk66]

Would u concider using a rust stopper before panting . Was thinking of doing it to my husky. ?

[@noelcahill6707]

Old belt is no mower good

[@davidfist7801]

What product did you use to paint the underside of the deck? Was it just regular metal paint?

[@xFlow150]

Great video! What kind of paint did you use for the deck?

[@ZippeNftw]

What do you do with all your finnished restaurations? Sell? Keep?

[@aidynroberson1486]

That mower is a beast. What motor does it have?

[@Mark-zz9rt]

Yanmar 3 cylinder diesel 23hp

[@kuntryhd1313]

Do you ever do push mower or is just easier an cheaper to buy a new one?

[@jimclements3190]

Thats a very nice mower, do you do contract work with it ?

[@BoiledOctopus]

Is it Hammerite you're using for the underside? Many thanks!

[@samuelthorogood3878]

how do you find bitumen paint lasts? i've not found it to last very well.

[@SuperBongface]

Good sir, are you using POR-15 for the underside of the cutting deck by chance?

[@John98512]

Have you tried rust converter on the underside of the deck?

[@AirplaneDoctor_]

With the price of JD parts being obscene and the company's fight to stop the right of the consumer to repair their own equipment, l really don't know why people still deal with them.

[@jameslockhart3102]

What did you paint the bottom with

[@dickdavidson3616]

Didn’t catch the name of your preferred make of riding mower??

[@lorenzomurgano5773]

clean the deck after every mow if you want this to live

[@harrisoncook530]

Hello daggerwin, ive recently picked up a westwood w11 with a very early gear shifter infront of the seat, bassically im wondering if you would be interested in doing a restoration video on it ? I know this sounds a bit stupid

[@Ottie193]

Its amazing how they manage to cram a 3-cylinder diesel onto what is basically a glorified riding lawn mower chassis with a hydraulic deck lift and hydraulic steering

[@Mikelp73]

Is that a diesel?

[@aserta]

18:41 however the procedure is, you have to remove the gearbox regardless. The belt passes under that bracket. One way would be to remove the left side bolt and loosen the right side, completely remove the far side bracket and the shielded pulley. Then you tilt the gearbox, but honestly, not worth the complication, you're better off removing it all because you can clean under. I'd probably remove them all to clean under where they usually rust. Sidenote, bedliner is a good paint for the underside, especially the rubbery stuff. It can take a good hit from a rock, but it won't chip. it doesn't last as long overall as paint does, but it isn't going to rust in spots either like normal paint does.

[@paulravitsky2898]

And there's the reason I will never buy a John Deere. Expensive parts and way over complicated. When greasing your front steering, jack up the front end. That will allow some grease to come out of the bottom to lubricate the pivot point. I use epoxy appliance paint to paint my decks. It's a little slicker and tougher than regular spray paint. Thanks for taking us along.

[@rjstandland4459]

How much property do you have because in your video it doesn't look like much

[@kevinbutton4580]

The pto shaft off the rear that just spins a pulley...that spins the blades pretty pointless

[@johanstahl5555]

You have a job beside your youtube channel but what are you doing?

[@nps5886]

I'm surprised they let you fix it as they are anti rtr

[@Daggerwin]

My machine I can do what I want lol

[@paulbowers7343]

£138 for a belt? All you did was pay for the JD logo on the package. Bet you can get the same length belt at a local industrial belt supplier for a bunch of £ less, and probably made by the same people who make them for JD!

[@Cinnamon_Shaey]

is there a reason you went for an official john deere belt? since they cost that much, i would probably have searched for a 3rd party one for cheaper, if they exist of cause

[@vasilem299]

Is it me or does this guy sound familar?

[@chrisbayus5189]

It’s not terribly surprising to hear that the belt was that much money. John Deere uses gold to get that particular shade of green paint; EVERYTHING John Deere is expensive!

[@joeclarke8578]

If you do want to sell it, let me know

[@eddiepatterson5025]

138 British pounds is 169 us dollars for a single belt. This is why I can’t afford a John Deere too expensive. I gave 98 dollars for 2 deck belts and this lawnmower rider was manufactured in 2004-2005 I thought I was gonna have a heart attack.

[@DanKoning777]

Where's p2 re: FIXING A CHEAP FOUR WHEELER QUAD BIKE? Imo it's frustrating to see new/different videos uploaded after watching p1 in a series and you're still waiting for p2. For me, watching multiple projects in no particular order takes away from what you like about each project. Again jmo.

[@tubeDude48]

Why didn't you just go to an Automotive parts house and get a belt?

[@audibell]

Get a honda

[@shadowbanned69]

This is why I hate John deer tractors. Not made for maintenance by John q public

[@furyyy6657]

Задолбал, со своими комментариями к видео

[@rocketrick1081]

138 for a belt is not a surprise. You should be glad you're not a farmer here in the US. They gogue them price wise and lock them out of being able to service their own machines forcing them to contact a dealership for service.

[@1977aliveandkicking]

👍