I Wired My Entire Race Car By Myself - Turbo LS S10

[@sbfnation2535]

Definitely a ford fan here. But that’s a sharp looking truck.

[@RegularGuyGarage]

Thanks

[@bluecollarfox913]

That’s a good lookin truck

[@RegularGuyGarage]

Thanks!

[@seanbrown9111]

He man you have some good skills and a nice setup for sure.

[@WhiteBoy1981]

Damm dude you done a hell of a job on building that truck and wiring it tuning is not all about timing sometimes less timing is good on a turbo application I think you need a loser converter and some dump valves get in touch with circle d or Hughes they will get you fixed up and there tuning classes you can take thru Holley but you will get there I’ll tell you a great place to start on learning to tune is Devan Vanderhoofs channel. Also you should had seen my first car I wired lol it was a mess the key with wiring is Patience and doing it correctly the first time also Holley has a self learning curve that the more you run it the more it learns and uses what your engine wants if it’s turned on but cool truck man and great job you should bring it out to Mexico 🇲🇽 with us one of these days when it’s fixed and lined out.

[@bennyboom63]

Following this truck closely I'm building the exact same truck. I got alot of questions that some you answered already. Good luck my man.

[@RegularGuyGarage]

Awesome. Thanks man!!

[@MrLowrider527]

Looks great nice work, Sweet Truck

[@RegularGuyGarage]

Thanks!

[@slowbra94]

That is super clean. I just got a truck to daily so I can start building a new motor for my 94 cobra and have a tow rig. Now I kinda want a race truck 😂

[@RegularGuyGarage]

I’ve always had a thing for Race trucks

[@freddiemoralez1536]

Heat rap hot side to lower intake air temperature.

[@RegularGuyGarage]

I Got an air to water intercooler and set up an ice tank for it

[@jesse1062]

More timing you pull the faster it build boost

[@RegularGuyGarage]

Problem is the converter is too tight and when I pull timing it lugs the motor down

[@jesse1062]

Maybe I leave around 5 degrees on the holley then bring back in

[@BmoreFox]

I had the same problem on my brake. I do 42° til 3lbs then yank the timing out. Waiting to put my new PTC in. Mine is way too tight now

[@RegularGuyGarage]

I’m going to try a dump valve setup first. If that doesn’t work then I’ll change converters. PTC is the way to go imo

[@BmoreFox]

@@RegularGuyGarage haven’t put mine in yet but I hope it fixes the issues I’ve been struggling with for a year. It’ll build whatever boost but hits a wall at 3400 & takes about 5-6 seconds.

[@mewrongwayKOCXF]

Awesome Truck there! May I ask what the paint is?

[@RegularGuyGarage]

It’s a wrap. Not sure what the color is called honestly 🤷‍♂️

[@mewrongwayKOCXF]

@@RegularGuyGarage awesome!

[@Six60_Garage]

I recently installed the Motion Raceworks operator shifter in my car. It’s a nice piece!

[@RegularGuyGarage]

I’m excited for it

[@540chevhell9]

Wow I changed my user name and lost contact with your channel. Last time I was here you'd started modding the green Camaro!! A lot has changed 🤣

[@johncarson9691]

Wrap the exhaust pipe under the intake

[@adamcartwright6220]

So if you don’t mind my asking, where did you look to learn some of the turbo stuff that you know. Thanks in advance. Trying to build my first ever turbo build

[@RegularGuyGarage]

I used to be a diesel mechanic when I was younger.

[@adamcartwright6220]

@@RegularGuyGarage Definitely learn plenty doing that I’m sure! Thank you for your content and knowledge!

[@freddiemoralez1536]

Converter to tight to get on Trans (dump valve) needed? ?

[@RegularGuyGarage]

Changed it to a looser converter already. Works good now

[@tiarragipson59]

What do you plan to do with old shifter after you replace it?

[@RegularGuyGarage]

Sell it

[@kyore789]

What do you do for a living?