Had a rough night in the shop making some pretty scrap and felt demotivated. Woke up, grabbed some coffee, saw this video, and figured why not. Per usual, I had several "ah ha!" moments, took notes like a madman, and am now completely over my funk and ready to make some chips with this new knowledge! Thanks for all the killer content!
@chrisrokz90056 жыл бұрын
That is a great tip. Just be careful with the straight line lead in. Certain controls do not like cutter comp G41 G42 in line " tangent " with the cut. This can also leave a bit mark when you have to switch to a larger cutter then anticipated. I still arc in to give a buffer between the comp and the cutting.
@Regalmetalworks6 жыл бұрын
That was really helpful! Had same issue on a part and just did an overlap but it didn't remove it completely. Starting and finishing on the start of the curve would of made a big difference! Thanks John!
@nyccnc6 жыл бұрын
Thanks Cole!
@samboles87966 жыл бұрын
I actually already new how this worked but I enjoyed the video anyhow Thanks for streamlining Fusion 360 John I hope the folks at Autodesk appreciate all you’re hard work, I know that I do!
@jimmer1476 жыл бұрын
I thing Finishing overlap is the ‘bug’ in the last op. some great info in there Thank you for taking the time to make these videos. I haven’t come across make all default before. Ramps cleaned will never have to be adjusted again woohoo
@prodesign81896 жыл бұрын
Great stuff. Keep this kind coming! I am getting to be one with the fusion and the 440 thanks to your keen observations and experience in 360 and the tips you put out there. You always seem to put something out at the right time, not long after I may have asked myself, what would John do? I Would love to talk my company into letting me come on out for a class again soon. I just wish you'd do one on set-ups and how to use your fixture plates...etc...Thanks again John!
@nyccnc6 жыл бұрын
We're working on it!
@VictorHernandez-nt3tw6 жыл бұрын
The last way you did it is exactly how I do it. I hate when other program lead in and out right at the middle of the part, unless absolutely necessary.
@bertr56506 жыл бұрын
Is that dot you are trying to lead out on not the lead in dot? Could you reduce the lead out arc to get your lead out closer to the preferred dot. Doing a great job on the videos John. I'd love to know the basics of how Julie and yourself sync the whole thing together.
@CatNolara6 жыл бұрын
I think you looked for the wrong parameter in the end there. The finishing overlap should be under the passes tab. ANd thanks for showing how to set a parameter as default, that's really useful for me. Edit: or your starting point isn't on the edge, since the lead in is straight you wouldn't notice if it's not.
@viaceslavkiptilov12034 ай бұрын
Thanks guys! Excellent technical (and not only) tutorials ;-)
@ROBRENZ6 жыл бұрын
Good stuff John! ATB, Robin
@nyccnc6 жыл бұрын
Thanks, Robin! How's your Fusion going?
@ROBRENZ6 жыл бұрын
We are slowly becoming better friends, thanks for asking.
@SamB22226 жыл бұрын
Hi John! Sorry if this is a dumb question, but I'm a hobbyist with a Tormach 440 and pushing the boundaries of my x-axis working envelope. Do you know of a way to force a SuperFly in Fusion360 to enter/exit from the Y-axis instead of along the X axis? I've been making a few parts that are long in the X-axis (9.75") and so a SuperFly exceeds the boundaries of the machine for lead in/lead out, but I would have plenty of room along the Y-axis for a Superfly to enter/exit. I have been doing this manually so far, but would love a way to integrate it into my Fusion 360 CAM operations. Thank you! (P.s. you were a HUGE factor in my decision to purchase the 440, so thank you again, I couldn't be happier with it!!)
@williamclark776 жыл бұрын
At the top on the "passes" tab change the "pass direction" from 0 to 90.
@SamB22226 жыл бұрын
Haha, that's amazingly simple....and yup, I do feel a little stupid now. Much appreciated, thank you!!
@cerberes6 жыл бұрын
very good John
@winkworks6 жыл бұрын
Very informative! Thanks, John!
@nyccnc6 жыл бұрын
Thanks Eddie!
@jeroen-surf6 жыл бұрын
Good one John, thanks!
@flyfaen16 жыл бұрын
I would just pick the side of the corner you picked first, but have a radial lead in and make the lead out just go straight out past the corner radius :)
@2222e1006 жыл бұрын
What about making your own finishing strategies using trace toolpaths?
@nyccnc6 жыл бұрын
Yup, that works!
@PuzzleboxProps6 жыл бұрын
That extra line is maybe just your "finishing overlap"
@nyccnc6 жыл бұрын
It's not!
@Hirudin6 жыл бұрын
I figured it might be that too, but I whipped up a similar operation and the same thing happened to me. Weirder yet, if I selected a point just beyond the point on the tangent, the apparent offset went away. And even weirder than that is that the bug (or whatever) only happened if I selected the point in the bottom left corner - selecting the equivalent corner geometry 90 degrees away (or 180º or 270º) worked correctly. And the weirdest yet, I made a second slapped-together file and tested it again, this time the lower-left worked as expected, but selecting the lower right made Fusion 360 ignore my entry point selection entirely and start the cut at some idiotic location. Changing the lead-in sweep angle from 0 to 1 degreed made the overlap bug reappear, but again only in the one corner (lower-right in this instance).
@Hirudin6 жыл бұрын
In case Autodesk sees this, here's a lil' video of the bug happening to me too. KZbin video: p2rBmWlgML4
@Xraller6 жыл бұрын
I use a huge 1200 inch radius lead out. When you use that over just a inches its almost impossible to see.
@DesignBuildTDE2 жыл бұрын
Very Helpful!
@DIRTYTHUNDERCUSTOMS6 жыл бұрын
More great info John!!!
@auhopu6 жыл бұрын
Yes, it seems you duplicated the last 2D Contour from a previous one and kept the original operation's finish overlap to a non-zero value. You debugged it yourself by seeing this segment is a finishing move.
@Ty_N_KC6 жыл бұрын
Depends on what your driving!! ;)
@jomme9186 жыл бұрын
Jep finishing overlap 1/2inch Would rather pick 0,5mm enough:)
@shamu38383 жыл бұрын
None of this should be necessary because if doing oring groove, for example, we are taking a finish pass of .002 If that’s causing a line, then there’s some other technical issue in fusion. I never had this problem in mastercam. Fusion, when milling oring groove round on od. Always get the witness line. Annoying
@crazyglue13376 жыл бұрын
Lead goes in. Lead goes out. You can't explain that
@jomme9186 жыл бұрын
Haha.. edgecam had a better option when i used it back in the dayz. Full lead in/out controll + center of area (easy for holes)
@kbutta016 жыл бұрын
jomme918 I can’t stand EdgeCAM... I used it for months at work we switch back to GIbbsCAM. The software is so unintuitive and clunky. It’s powerful but not user friendly at all. Not that GIbbsCAM is perfect either but...
@rlockwood26 жыл бұрын
you keep using 'make all default' .. I do not think 'make all default' does what you think it does :)
@MrMadDrago6 жыл бұрын
rob lockwood inconceivable!
@MorganOliff6 жыл бұрын
rob lockwood I keep mine set to tool diameter * .25 Hasn't been annoying yet. :)
@alanhardman24476 жыл бұрын
Morgan Oliff - You keep using that word... I do not think it means what you think it means...
@vinnyvince236 жыл бұрын
you keep making 'comments' .. I do not think 'comments' does what you think it does :)