INCREDIBILE! MINI welding machine that fits in ONE HAND - Topshak ZX7 250A

[@DanieleTartaglia]

🛑 🛑 🛑MESSAGGIO IMPORTANTE!! 🛑 🛑 🛑 Se volete nel mio canale youtube più contenuti FAI da te, tutorial e guide, iscriviti al mio canale Telegram SHOP. LINK TELEGRAM: bit.ly/2V9CWVY in questo modo potrò portare più contenuti dedicati al fai da te e postare invece su TELEGRAM oggetti in super sconto con coupon speciali. In questo modo ci saranno sul mio canale youtube meno promozioni a pagamento e più contenuti dedicati al fai da te Metti LIKE al post se ti piace come idea e magari scrivi un commento :-)

[@scottfrazer8376]

DEFECT ALERT: If I had my own KZbin channel, I would make a video about this DEFECT I found and corrected in my brand new TopShak ZX7-250A 110V welder, which I bought on Banggood. Apparently, this unit was assembled using five M3x10 machine threaded screws to anchor the 3 big heat sinks in the back of the unit, near the cooling fan. This was a HUGE MISTAKE on the manufacturers part, because the heat sinks have no machined or tapped threads for the M3 x10 anchoring screws to bite into substantially...but only crude SLOTS in the aluminum castings. You need to grab a standard #2 Phillips screwdriver and remove the welder cover, then use the screwdriver to check all five heat sink anchoring screws on the bottom of the circuit board, to see how many of them are loose and INCAPABLE of even being sufficiently tightened in the first place. I just replaced all five LOOSE heat sink anchoring screws with some slightly bigger sheet metal screws, which have tapered threads very similar to self tapping screws. NOW all five screws can be tightened very securely. You really don't want any of those 3 heat sinks EVER coming loose, because the result will eventually be a certain failure of the welder. If you rely on the factory installed M3 x10mm screws to keep those heat sinks secure, your welder is headed for certain failure. Luckily, this shortcoming is very easy to remedy.

[@joshchelvolski1033]

Hold moly thats for posting this. I was thinking of purchasing the welder from banggood and using it right away, after after getting it wired up.

[@joshchelvolski1033]

Is the welder actually 110v or 120v. Would this welder trip a 15amp circuit breaker ?

[@scottfrazer8376]

Call it 110V or 120V, but at the end of the day, it is the same old single phase AC wall outlet supply voltage that we all use here in the USA for most of our common AC powered appliances and devices. MOST of the smaller devices and appliances rated for 110/120VAC are going to run on any outlet that is supplying anywhere from 90vac to 130vac. But anywhere between 110vac to 120vac is optimum. I have found that 113VAC to 118VAC seems to be about the national average wall outlet voltage, which is just fine. I don't KNOW that there would be much DIFFERENCE....whether the manufacturer rates the device to run off 110vac or 120vac. But I really don't recommend running ANY kind of 110/120vac welder or plasma cutter on ANYTHING LESS than a common 20 AMP circuit breaker. That would be the BARE MINIMUM for running even the smallest inverter welder....especially with the welder output current turned up to MAX OUTPUT. You might get away with the 15 AMP rated breaker IF you are running NO OTHER DEVICES off that circuit AND you are keeping the welder power dial at NO MORE than 50% power. Remember that the inverter output circuit depends upon IGBT inverter power for welding. If you try to run Isolated Gate Bipolar Transistors on an AC supply circuit that is sagging too much with ac voltage drop during heavy current draw, you can literally FRY the Isolated Gate Bipolar Transistors and/or rectifiers and it won't matter HOW BIG the heat sinks are, that the IGBTs and rectifiers are mounted to...inside the inverter welder. Same thing can happen running the welder at MAX OUTPUT on a cheap, skinny little 18AWG extension cord. Running a welder on a circuit with a higher current rating and heavier wire than the minimum required will keep the wiring inside your walls from getting hot, so it is always a good idea to have at least one 110/120vac circuit in your dwelling that has at least a 20 Amp breaker...just for running power tools or a small welder. For the sake of thermal headroom, I would go even higher and run the welder off 25A or even 30A breaker....WITH the appropriate gauge wiring to SUPPORT the 25A to 30A breaker of course. When it comes to running a welder, MORE is ALWAYS BETTER in terms of ac supply current. This is why it is nice to have a DUAL VOLTAGE welder, such as the 160A Deko Pro MMA welder, because you can always just plug it into any 220VAC dryer outlet, which almost always has a higher current breaker than your most common 110/120vac outlets . But running the Deko pro on a 220vac outlet will only draw about HALF the current (Amps) as running off a 110/120V outlet. So almost ANY 220V outlet would be far greater for running a smaller welder, even if the breaker is an OLDER 220vac circuit and rated only for 20 Amps. But I think you will find in most modern dwellings, the 220vac dryer outlet will usually be on a 30 AMP breaker, which is even better. But again...ANY 220VAC outlet would be far better for running even a smaller welder...especially if all your 110/120vac outlets are only rated for 15 Amps!!!

[@joshchelvolski1033]

@@scottfrazer8376 whoops I ment to ask if the welder unit was 220v or 120v. 😅

[@salvadorgonzalez9147]

Good looking-out Scott...

[@htconesv897]

Thank you for your time and effort showing this machine! I like the written communication much better than speaking.

[@riks.1773]

Hold rod holder at a 30 degree angle and once arcing move in a little downward spiral for a smooth weld.

[@kingsleyokwudili3206]

Thank you so much. I was looking for a small welding machine to buy. I think your video has really helped.

[@electronic7979]

Excellent product

[@moamgaphonemga6166]

Com certeza, daqui a pouco tempo Daniele vai automatizar o processo de solda quando for em linha reta. 👍

[@YKC119]

스텐레스도 용접이되나요?

[@DanieleTartaglia]

HURRY UP, FOR TWO DAYS THIS INCREDIBLE WELDING MACHINE IS ON BANGGOOD AT THE PRICE OF 35.82 EURO NO CUSTOMS AND ONLY 29 PIECES AVAILABLE. I HAVE ALSO INSERTED A DISCOUNT COUPON THAT YOU CAN USE... ⬇︎⬇︎⬇︎⬇︎⬇︎ purchase link and coupon ⬇︎⬇︎⬇︎⬇︎⬇︎ 🔴 Topshak ZX7-250 250A Mini Electric Welding Machine: bit.ly/3zqifn2 💰COUPON: BG9ac093 24%OFF

[@georgenicolaidis7550]

The coupon code does not work for this item.

[@DanieleTartaglia]

@@georgenicolaidis7550 it does not work because it is on special offer. if you are interested take advantage of the Banggood promotion. the banggood offer expires tomorrow

[@AndreiIR000]

Very nice! I never welded but this makes me want to try. Thanks Daniele!

[@jacksyful]

you should push the pool , not pull!

[@chongshenchang9367]

Sir, Even if you are a first time welder, your welding is very good. .👍👍👍

[@KillersAreQuiet133]

No its not lol

[@mohankrishnasamy1456]

Thank you. From. Malaysia 🇲🇾

[@Vincenzo_F]

*Azz!!! Tanta roba....* 👍🏻

[@pacohaking2815]

Mi sembra un bel oggetto! Da ora in poi non vedremo piû legno ma solo metallo nelle strutture 😜! 1^Consiglio usa lo spray antiaderente prima di iniziare una saldatura, riduce le scorie e migliora l’unione! 2^consiglio, prima di inizire la vera saldatura “scalda” l’elettrodo facendo un paio di saldature su un pezzo di metallo martire! Anche in questo caso la saldatura verrà meglio! A presto e continua cosî!

[@DanieleTartaglia]

Grazie mille per i consigli, ma queste cose le avevo viste fare da altri youtuber. solo che io lo spry non ce l'ho perché non sono un saldatore :-) Non hai idea di cosa ho costruito artigianalmente per crearmi una maschera. Comunque vorrei fare anche cose in metallo :-) ora che ho la saldatrice, qualcosa devo creare

[@pacohaking2815]

@@DanieleTartaglia lo capisco bene, anche io alla prima volta ho fatto una saldatura peggio del peggio. Poi con la pratica. Comunuqe lo spray lo trovi in qualsiasi negozio ben attrezzato e ti assicuro che ti migliora la vita. Il fatto dello scaldare l'elettrodo prima me lo ha consigliato il mio vicino che è un saldatore provetto e anche questo funziona bene; essendo "caldo" inzia subito a saldare senza dovere "toccare" il pezzo svariate volte per innescare l'arco.

[@mdani76]

@@DanieleTartaglia spendi qualche euro e comprati una maschera automatica, finché non si salda ad occhi chiusi è molto utile... e comunque anche dopo! 🙂

[@FabioV1970]

@@DanieleTartaglia Un' altro consiglio la saldatura va eseguita da sinistra verso destra per quella ad elettrodo e da destra verso sinistra con quella ossiacetilenica. Con un pò di pratica vai alla grande. Complimenti sempre ottimi video. 👍👍👍

[@DanieleTartaglia]

@@FabioV1970 Grazie per il consiglio, non lo sapevo :-)

[@jaseemhaneef7958]

Your all video are supper and help full

[@MadAudiosystem]

Leggendo qui e li sembra che i dati dichiarati siano un po' fasulli. Questa saldatrice ce la fa sulla 3kw casalinga oppure vado su altri modelli a inverter? Grazie in anticipo

[@heathfiedler]

Got one like this, have yet to use it. But i was wondering what size rod can be used with this other than what was provided? Im sure i cant use very large rods but i can assume some standard size though not for too long due to duty cycle and what not

[@SolarSeeker45]

Probably 3/32nd 7018. I know it sounds like gibberish but they'll know what you're talking about at the store.

[@heathfiedler]

@@SolarSeeker45 tried it and honestly im happy with it. used it to weld up a gokart fame in spots it had cracks.

[@robertblackshear8963]

I have a havadou225 about the same size and it runs 1/8 6010 like it built for it. These tiny stick welders are slowly taking over.

[@sligacheese6470]

Just bought MMA-250 it’s awesome to see this under 100 bucks 20 years ago this would cost over 2000 I used them then.

[@DanieleTartaglia]

NUOVI coupon con SUPER sconto: LINK DELLA MINI SALDATRICE: bit.ly/3zqifn2 Coupon Price: €30.6🥰😍 Coupon Code: BGb899b8 Warehouse:CZ EXP:15/10 100PCS only

[@bobbybalderas1038]

Ser,Mam,can,I know how much d price of your mini wildingmachine,

[@redbishop71]

Is this machine is the 2 minute continuous used then 8 minutes rest?

[@gabiladarlington1456]

Which stick did you use?

[@ar.officiaall]

How did you get it to start I bought one and it won’t spark up

[@igomez26]

I like the remote start, dual fuel, and it is easy to move around. Great for the RV!

[@jasondonavich2758]

Would this work for welding exhaust piping?

[@chongshenchang9367]

I recently bought this mini igbt Arc welder from Amazon. It's nice, though I'm not a welder, I found it out to be good. But anti-stick function is not satisfactory. I received both cables, goggle,iron brush and gloves.

[@maxhammontree3169]

Try a continuous arc, not so much pecking.

[@eyangsuburr7296]

Mantap coy... 👍👍👍

[@hakanustundag5857]

Kablo ölçüleri nedir ustam içinden kablo pense çıkmıyor nasıl bir şey alacız.

[@27diegoedilsonquisbertcals77]

Que buen contenido amigo... sigue adelante...

[@Pakyed46]

Can u review the latest portable welding

[@celegela]

Si può saldare anche l'alluminio?

[@DanieleTartaglia]

Purtroppo no, l' alluminio si salda a tig

[@matteomarchetti4205]

esistono elettrodi per saldare l'alluminio, però sono molto costosi e difficili da usare. inoltre necessitano di una saldatrice che abbia una tensione a vuoto abbastanza alta e non credo che questa macchina la abbia. La cosa ideale sarebbe giustamente il TIG, ma serve una macchina AC/DC.

[@jeffgood6441]

How much did this cost and is it still holding up

[@mdassadurjamanliton4648]

Ok many many thank you

[@alknis]

Да, неплохой аппарат. Пока не могу, а потом наверно куплю.

[@leverman7517]

Why did the site say "plastic welder"? is the case plastic or does it weld plastic?

[@muhammedadil4463]

It's so cool I have it but another brand this is very portable device 😍

[@ankurkujur4637]

Bhaiya kis app se order kare

[@tubozza]

funziona con elettrodi basici?

[@hakanustundag5857]

@MehmetOfficial09 Ustam bunu aldım kablo pense içinden çıkmıyormuş sanırım kablo kaç milim alacam soketleri nasıl olacak bana yazarsan sevinirim. Kablonun uzunluğu kaç metre olacak çubuk kaç milim alacam bunları yazarsanız iyi olur. Teşekürler.

[@kimvermeulen6840]

i see u pushing with the welding stick thats a nono . if welding from left to right the stick has to go from left to right indeed the angle is +- 30 degrees but u have to see how ure meltingbath form is but for a first time u done pretty well

[@mgchavezpr6497]

Funciona 110v?

[@Antonio-ge6rz]

Voglio prenderla anche io, hai un coupon nuovo?

[@DanieleTartaglia]

Si LINK DELLA MINI SALDATRICE: bit.ly/3zqifn2 Coupon Price: €30.6🥰😍 Coupon Code: BGb899b8 Warehouse:CZ EXP:15/10 100PCS only

[@Antonio-ge6rz]

@@DanieleTartaglia ahha c'è il trucco, non fa niente ti ringrazio lo stesso, costa di meno senza coupon. Grazie mille!

[@mojama7]

Can it weld aluminium?

[@milospopovic6978]

Could you measure please current with amp clamps ?Im not sure this guy can produce 250 A.Maybe 100-120 max,but for home and DIY its more than enough.

[@klausbrinck2137]

For this welder, simply divide by 2...

[@eliaschavezcarrasco8569]

Dónde lo puedo comprar , o como hago para adquirir una de estas máquinas de soldar?

[@variable22]

Hola Daniel,te aconsejo, aumentar la intensidad de la corriente,verás, que los resultados mejoran.Ojo en el espesor de los metales,más grosor,más intensidad,un saludo.

[@DanieleTartaglia]

Thanks ;-)

[@farikkun1841]

is the reason it has little transformer is that is has huge ass capacitor?

[@jmy7622]

Ilike it , I just wish it came in a 110v plug.

[@geordiemik72]

It would be interesting to cut across some of those welds to see how much penetration you're getting.

[@DanieleTartaglia]

if you watch the whole video, there is a part where I tried to cut the ring, but the soldering was so bad that I gave up. look for it in the video and you realize that it welds well

[@ATLaboratory]

Bella questa, l'hanno mandata anche a me ma devo ancora provarla.. son contento che non sia esplosa subito haha:) scherzi a parte è molto piccola e sono veramente curioso di vedere come si comporta rispetto ad altre saldatrici:)

[@DanieleTartaglia]

Ciao, considera che io non ho mai saldato, e se fi sono riuscito con questa, significa che hanno progettato una saldatrice che aiuta molto. Poi è piccolissima e molto leggera, comoda da portare via per piccoli interventi. Vedrai che piacerà anche a te :-)

[@ATLaboratory]

@@DanieleTartaglia si infatti mi stanno prudendo le mani per provarla:) poi il costo è veramente alla portata di chiunque, anche solo per fare delle prove e capire se la saldatura è un qualcosa che veramente si vuole provare a fare! A presto:)

[@peppomaker]

Visto il prezzo si potrebbe anche convertire in un alimentatore da banco ? 😅

[@27diegoedilsonquisbertcals77]

7:40 watch out for epileptics XD

[@DanieleTartaglia]

😂

[@DanieleTartaglia]

@Sherylin I had the mask

[@DanieleTartaglia]

@Sherylin So if you have these problems, you don't watch videos on youtube. Or do we ban all channels that carry out welding?

[@AndreiIR000]

@Sherylin I don't think he fully understood your message. What I understand is that a proper warning should be presented for a few seconds before the dangerous frames. What the author seems to understand is that he shouldn't have produced and published this content. Please confirm if my understanding is correct.

[@AndreiIR000]

@Sherylin Just trying to help by clearing confusions. Not trying to be a smart-ass.

[@MrKannangara]

Pl send me the prize of this welding machine

[@marioneallin7400]

Ciao Daniele, faccio veramente fatica a credere ai dati riportata in targa, sopratutto il Duty cycle di ben 250 A al 50%... Sarebbe interessante fare prove a carico con misura di corrente e tensione, monitoraggio temperatura e intervento protezione termica

[@ratulrakib8360]

Please make DC to AC covert indevetor

[@zlatimirivanov3615]

Not so bad for an inexperienced welder :)

[@DanieleTartaglia]

thanks, it's my first time :-)

[@zlatimirivanov3615]

@@DanieleTartaglia Now you can make everything (almost) . Waiting for new cool DIY :)

[@MrTipsoTV]

Not bad for a 1st timer..

[@damianocirillo5329]

Salve! Bel video sicuramente, ma quello che non si vede è che stia saldando con quella saldatrice, potrebbe aver usato anche un'altra,non per fare la mano del diavolo ma se ne vedono di tutti i colori

[@lucianoiacoletti5725]

Un oggetto veramente interessante, soprattutto per i piccoli hobbisti che non gradiscono l'ingombro di una grossa saldatrice. E poi un oggetto recensito dal grande Daniele è senz'altro un best seller

[@DanieleTartaglia]

Grazie :-)

[@simoneusala]

@@DanieleTartaglia come ti sei trovato col ciclo di lavoro utile? Nelle caratteristiche dice 60%, é veritiero?

[@marcobettoni463]

A me non tornano alcuni dettagli ameno che di non essere stato attento Si sta utilizzando un normale elettrodo da l 2,5 mm non basico con una corrente al di sopra dei 150 amp? Il mio vero dubbio è la massima potenza anche se utilizzata con un ciclo al 20% sono sufficienti i 3 kWh standard?

[@johnconrad5487]

The wire on that transformer is not capable of 225 Amps. So maybe it is good for 100 Amps or so. The power semiconductors are mounted on Heatsinks right up against the fan so the get adequate cooling. They could make it a little bigger and mount bigger Semiconductors in the board and a larger transformer and they could really reach 225 Amps if the input power can handle it. I dont believe that knob does anything. Its a great display toy.

[@JESS-cm7ko]

Price please

[@ruffano1993]

Mmm interessante.. inverter, probabilmente senza l'anti stick la vedo molto bene per fare una tig casalinga

[@ivanjuca7598]

Grazie Sião. Like garantido 👍

[@remesann3045]

Rate....?

[@linolino]

Sbaglio o hai messo la pinza sul positivo ? se è così di solito va sul negativo a meno che gli elettrodi non richiedano il contrario.

[@MaritesMare]

How much

[@shamastechnicalinfo4951]

Good

[@me4taki9oh]

I bought a DC welder for 62 euros. It did not work for 100 volts.

[@sparkyindahouse]

it cannot be shipped to the UK people....looks like a good little unit tho

[@ginofastidio4720]

A Daniè ma sto video l'hai fatto tu o te lo sei fatto prestà? 🤔

[@DanieleTartaglia]

Perché?

[@ginofastidio4720]

@@DanieleTartaglia non ti si vede, non ti si sente...

[@DanieleTartaglia]

@@ginofastidio4720 ahahaha Hai ragione, ma ho molti piu utenti internazionali che italiani e in questo modo riesco a farmi capire da entrambe le parti.

[@satishsheoran6818]

इसकी कीमत क्या है।

[@leverman7517]

On their site they had one for 59$ US dollars Are these for real?

[@klausbrinck2137]

35 is the average, some find it for only 15... Duty cycle is then about 200%, cause each time it heats up, u simply use the next one (of the 4 pieces u have bought ;-), and so on, till the first one has cooled down again ;-) Just swap the cables from machine to machine...

[@ramosnick9564]

Location po for enterest

[@bobbybalderas1038]

How much nmn Po yn

[@muhammedadil4463]

I don't believe this was your first experience with welding 😱 When I was start to Welding I ruined half box of welding rods because when I tried to weld each rod will stick with metal and burned 😁

[@ShiningForce07]

Probably your machine hasn't got anti stick function, amperage is too high or the electrode is a bit damp

[@muhammedadil4463]

@@ShiningForce07 no it is a base model it can only adjust ampere not even provide ammeter

[@Piano_sessionfree]

Demasiado amperaje

[@superspecialty5169]

Wow, opening a cardboard box with a razor knife!

[@shahinshiblu3848]

Please make a mini welding matching

[@ZlatkoGrujic]

👍👍👍👍👍

[@marcomarco6123]

...ecco Daniele, per "colpa" tua l'ho comprata 😅

[@DanieleTartaglia]

Quando ti arriverà, mi ringrazierai...te lo posso assicurare :-) comunque grazie per la fiducia.

[@brunop7032]

A quel prezzo è sicuramente un affare ... da tener in casa e usarlo qlc volta con elettrodi piccoli . Ah...non saldare sul piano legno. Ciao

[@mechanicula]

👍👍👍☀️👍👍👍

[@kapitanhakab9276]

Sig.. Daniele ma...

[@OrretteWright]

❤

[@davidemarchi6366]

How can you suggest a welder being you a beginner? You don't have experience for suggesting a welding machine in my opinion. Obv you take some money from affiliated link...

[@luigi_com]

Daniele, gearbest ti ha fregato tanti soldi ? (per chi non lo sapesse, ha chiuso)

[@DanieleTartaglia]

Perché? Cosa centra gearbest?

[@luigi_com]

@@DanieleTartaglia mandavi i suoi link come affiliato o qualcosa dle genere

[@DanieleTartaglia]

noooo...non lo sapevo. Mi hanno contattato migliaia di volte per lavorare con loro, ma sono sempre stato fedele a Banggood. Con me si sono sempre comportati bene e spero non faccia la stessa fine. Mi dispiace, avevano prodotti interessanti. chissà cosa avranno combinato

[@luigi_com]

@@DanieleTartaglia daniele controlla il link (sotto l'altro post non posso scrivere), mi dice che il coupon funzioan solo con la saldatrice 1713642

[@DanieleTartaglia]

@@luigi_com prendila adesso che è in sconto, il coupon serve quando la campagna è finita. costa 35 euro con iva inclusa.

[@Auxbeam]

Ciao, hai bisogno di una buona illuminazione per la tua auto per aiutarti a guidare meglio, fuoristrada. Siamo il produttore di illuminazione professionale per auto da quasi 20 anni e stiamo cercando sponsorizzazioni!

[@808botox]

Costruiscine una!!

[@DanieleTartaglia]

Si potrebbe anche fare con due trasformatori per microonde, ma è troppo pericolosa

[@AIdle42]

👍👍👍😎😎😎

[@Sukhideas]

130 th view

[@tim_timonya]

Aka Касьян

[@ruffano1993]

Primoo

[@Piano_sessionfree]

Table is death

[@igorantonof705]

Кто так криво варит.

[@PabloEsgallhardo]

thats a weak weld

[@MrLarry-gr8]

Am I the only one that has noticed this? I would of been like wtf is this crap! The covers edge at the corner is bent inward... I would of straightened that out first thing upon removing the cover. But that's just me. You know it really erks me to see at the end of the video that the cover still is bent! Bro please straighten that out... I won't be able to sleep until you do...

[@melvinthemechanic]

Wtf are you doing

[@skysurferuk]

Just... no.