Inner Tie Rod Replacement - Fiesta ST

[@ryanhughes7971]

Great video mate, my focus ones need doing and i just wanted a nice clear English video for reference, this is spot on thanks

[@jaymono6498]

Thanks! Hope it helped :)

[@bobmarleystoe]

i wouldnt pay too much attention to him he turned the adjuster nut the wrong way . and he pays a guy to adjust his headlight beam ffs .and those tie rods are fucked how he never noticed that while driving is beyond me.

[@thapipi]

What is the special tool to take out the inner tie rod called ??

[@stum8374]

Hi I'm about to do the same-how to get at the big jubilee clip !!! WHERE did u get the tool to take off the inner tie rod,I'm not inamered with the music.

[@stevemunro4668]

Informative video, I have a Mk6 that is clunking from the front Offside, I can see obvious movement and suspect the Inner Tie Bar..... your video suggest it should be a straight forward job. Did you sell your Tiebar spanner ??

[@davidstirland1873]

watt is the tool called

[@harry4410]

Great vid keep them up I literally did one of my inner and outer tie rods as there was play too. I used an extendable tie rod tool with extensions and a breaker bar, it came off so easy.

[@jaymono6498]

H4rry_ thanks! These tools make the job so much easier. First attempt mine didn’t come off and I thought I was gonna have a hard time, but second attempt they came off. It made trying to get them off so easy!

[@brettmowle1843]

how did you get the air vents out to paint the outer ring pretty please. i have been scrolling threw ya vids and have not found it anywhere

[@jaymono6498]

They're spray painted red, you can remove the, and spry them any colour you want!

[@TheRjsowter]

I have a question, the headlight you have installed, where did you get them or do you know somewhere reliable to buy headlights from?

[@jaymono6498]

R S they’re the ones I’ve got are from a company called Junyan, you can find them on eBay quite easily

[@TheRjsowter]

@@jaymono6498 I did see them, didn't know how reliable they were. Thank you

[@jaymono6498]

R S mine have been pretty reliable, however the LED one one side did play up for a while and started being slightly dimmer than the othwerside

[@TheRjsowter]

@@jaymono6498 okay thank you!

[@samfixes2179]

Did you buy this car second hand or brand new and what sort of ford fiesta is it and its 2006

[@jaymono6498]

Sam Fixes yeah I bought the car second hand back in December. It’s a 2006 Mk6 Fiesta ST150

[@RelaxingVibes202]

How will I know if my inner tie rods are worn?

[@jaymono6498]

it will have a lot of movement in the joint, you might heard knocking noises from the front of the car when driving over bumps or rough surfaces

[@bobmarleystoe]

dont ask him he didnt know either ffs.

[@chloelawrence8572]

Mine has humbling noise at 70-80 any idea what it could be?

[@jaymono6498]

Does the steering wheel wobble if you're not gripping it to hard at that speed also?

[@chloelawrence8572]

@@jaymono6498 yeah sort of mainly just the noise tho kinda depend on the road, think it could be wheel bearing right? , also think my shift arm is worn as gears go stiff after long journeys

[@jaymono6498]

Chloe Lawrence sounds like a wheel bearing potentially, does it make a nasty almost creaking sound when traveling at like 5-10MPH? Sometimes with wheels bearings you only hear them if your traveling really quick or really slow. The stiff shifting is a really easy job, just need to grease up the joints where the linkages join, there’s plenty of videos online of how to do it.

[@chloelawrence8572]

@@jaymono6498 thanks I will check it out, going to jack it up tomorrow and give the wheels a wiggle, yeah have seen some videos since I last commented and will have a go at doing it... the wheel bearing job will be a garage job lol

[@jaymono6498]

Chloe Lawrence how’d you get on? Manage to figure it out yet?

[@isoconfused8744]

How did you get the outer Tie rod off, I cant get mine free on the lengh where you did 19 turns... mine is corroded itself together so much, if I cant get if off I may have to do both inner and outer.. info on the tool?

[@jaymono6498]

Iso Confused I had only replaced the outer tie rods the week before so they weren’t corroded on. I’ve had to cut them off before in the past! Are you trying to loosen the inner tie rod bolt or unscrew the outer tie rod itself? Try letting some WD-40 soak over night, and if it’s still not moving use a blow torch if you have one available! The tool is just from eBay, called an Inner Toe rod remover/installer. It’s really hard to get a spanner to remove them so this tool makes its ALOT easier 😀

[@isoconfused8744]

@@jaymono6498 ye I watched the previous. I may have to cut off. To get the inners out. Can you provide some details on that tool..

[@jaymono6498]

Yeah if you have no luck with WD-40 or heat you're definitely gonna have to cut them So the tool just slots the Inner tie rods through the middle, and it has a different inserts for different sized inner tie rod heads, and you simply put a ratchet onto the end and use it as a kinda breaker bar to remove or replace the inner tie rod - really useful as its really hard to get a spanner in the right position to remove them. You can find them on ebay or Amazon for about £25 if you type in Inner Toe rod remover/installer.

[@isoconfused8744]

Had coil overs fitted and asked guy to do tie rod ends, in the end he said he couldnt get them off.. so I have phoned around and what I think are high quotes of £120 -£140 with me supplying the tie rod ends.. So Im just going to buy the inners also, and the tool and angle grind the olds off! - Do you grease any parts up btw?

[@jaymono6498]

You can get the parts for like £25 each so the £120-£140 I guess is the garage making their profit ontop.. I didn't grease any of the parts up for this job, some previous gobs I have, thinking of it the outer tie rod probably could have done with some grease

[@matts_st7107]

Great video again Jay! Good thing you didnt overtighten the tie rods 😁🙊 Looking forward to see more videos of the ST150 👌

[@jaymono6498]

Matthias Steenkiste more every week as normal!

[@mclarksays]

ALEXISONFIRE 👀🤘🏼🤘🏼

[@DivideSubtract]

What sizes of spanner do you need for this? Thank you

[@jaymono6498]

I think it was 19m but it was too long ago to proper remember!

[@bobmarleystoe]

depends the size of nut

[@JarlJorvik666]

My fiesta mk7 is 32mm if that helps

[@CarlMCL]

isn't "tie" the american term of track rods and track rod ends?

[@jaymono6498]

CarlGB probably yeah!

[@bobmarleystoe]

yes

[@ukmud6218]

It's Making me winch seeing you put your legs under the car, I'm 5 years too late 😂

[@garywalker3818]

good job

[@waynerountree9284]

Top video

[@ilfordino-fordfiestatutori8725]

I had the same issue on mine, twice. I did a tutorial, you can also find it inside my channel.

[@hiadm1477]

tank you for the video

[@waynerountree9284]

Top video

[@waynerountree9284]

Top video