Install Lexus V3 Needle Boards | DIY Fix & Upgrade Instrument Cluster Gauge Needle LED Lights | TAE

[@soyeldiego4878]

Just picked up a 1992 Lexus ES300 that has the LED needles along with the cluster lights burnt out and HVAC lights. Watching your video gave the confidence to tackle the project myself. Will be ordering your repair kit soon. Thank you for your very informative video.

[@TaninAutoElectronix]

Hey Soy we're so glad that you were able to use our videos to help you. Let us know if there is anything we can help you with.

[@brm4141]

I am thinking about replacing the RPM and speedometer needles which do not glow red any longer but function. My mechanic is pretty good and said he would tackle it, but want information from folks who have done it. Thank you.@@TaninAutoElectronix

[@TaninAutoElectronix]

@@brm4141 Unless your mechanic has a proper soldering station, tools, and the ability to solder delicate and precise electronic parts it might not be a good job for him.

[@brm4141]

What else do you have in your bag of tricks for 1994 ES 300?@@TaninAutoElectronix

[@TaninAutoElectronix]

@brm4141 recommend buying our complete plug and play cluster! taninautoelectronix.com/product/1994-1996-lexus-es300-instrument-cluster/

[@grabir01]

Ok.. Just finished my install SC300. I only did my Temp and Fuel. Tach and Speedo ok. Did not remove my cluster from the car as I could only get one plug out the other 2 were so tough I was afraid I would break the cluster . So.. I simply pulled it out far enough and removed the bezel and needles from there. Turns out to be a good way to do it as once you get your new needles installed, they will need test an calibration before you put the glass or bezel back on. I followed his instructions for removal and install of led strip to needle. Tested with a 9V battery. I knew where the fuel gauge needle needed to be. Pushed it back on. Turned on key, it lit up well. Yea!! Not the same as factory as you can see the segments and its brighter which is a benefit. Over all happy though. Started the car and waited for 20 mins or so as I know my Temp is just under half. Once car was warmed up, I pushed on the Temp needle. It too lit up. Yea!!! Noticed my fuel needle was going up and up and up slowly. Removed it. Added another hit of hot glue for more weight. For my sc300, it needed a full length of hot glue for balance. For temp no extra glue needed but I did notice it would not go off of half way when the key was turned off. The Temp should go down when key is turn off. I had to pull up on the needle a little so it could move freely and return to 0 when key is off. Fuel I no longer knew where its calibration point was since it climbed on me, I had to remove it and add some glue for weight. So... I left the needle off, went to a filling station and filled it up. I waited around 5-10 mins as it takes a while for it to go to full... Once I felt enough time had passed, I pressed it back on at the F position and proceeded to drive the car around. I noticed my temp gauge was too high, it took me 4 or 5 more times of plucking it with my fingers and re positioning it to just under half, once where it should be, I would turn off the key to make sure it would go to zero. Fuel does not do that. It stays where it is. So.. I had to drive the car and burn 1/4 tank of gas to make sure that needle too was working. So.. All in all.. This is a day project and you need to be careful and know what you are doing. You have to know how to soldier also. I would put difficulty level at medium. IF you have some burned out bulbs that also need replacing, then you will have to work on getting all 3 plugs off and remove the cluster from the car.

[@TaninAutoElectronix]

Thank you for the insight on the repair. Its good to get peoples input on the repairs being done using our videos to help guide them through the process. Hopefully it will be helpful for the next person.

[@naexuipper5899]

very informative and great instructions , we will order the boards very soon!

[@waelmostafa339]

Thank you very much for the information... cheers 🍻

[@sykosy]

Got my kit today. Got everything installed and looks amazing. Just one issue now. Both my tach and speedometer won’t move. Any thoughts?

[@TaninAutoElectronix]

Hello! I'm glad to hear you're pleased with the needle kit, sorry to hear about those gauges though! Its a challenge to diagnose an issue like this without having the item in front of us, but we'd be happy to see what we can do! Please email your contact and vehicle information to us at [e-mail] (or call 262-456-4147) and we'd be happy to help!

[@erana2670]

hi how are you, thank you for this video, can you tell me where i can find this needles, all 4 of them, and how ca i change the leds in the board?, thank you

[@TaninAutoElectronix]

bit.ly/lexus-v3-needles

[@Linkinpark96Mr]

I ordered a few days ago and received it right away. I am very satisfied with quick shipping however, my one doesn’t have a code extension for the needle in which +- positioning in reverse as this video explained … I have 95 lexus sc300. I haven’t tested yet but should I try it out first or what can I do?

[@TaninAutoElectronix]

that doesn't apply

[@Timedspark]

Just did the kit plus dash lights for a 92 sc400. Would the fuel gauge not go to whatever the sending unit is telling it? The needle can only go on 2 ways due to the 2 power pins and the centre pin

[@AdventureswithLouie]

Where are you guys located at?

[@TaninAutoElectronix]

Our address is: 7012 HWY 31 Suite 100 Racine, WI 53402

[@debrahall4170]

How can you tell if the moter is not working? I have a 1993 Lexus SC 300 and my speedometer does not work.

[@TaninAutoElectronix]

Hey Debra! If the gauge needle isn't moving at all, or is reading inaccurately, it might be due to the motor failing or starting to fail. Send a message to our customer service department and we'd be happy to provide yo with a quote to repair the cluster for your SC300! [e-mail] 262-456-4147

[@Alex_bkr10]

My RPM and Speedometer needles fell off on their own. Funny but, how do I get behind the plastic cover to put them back on? Thanks

[@TaninAutoElectronix]

Remove the lens, it's screwed on from the back side

[@shaunoguinn1015]

And how do you separate the 2 metal pieces if you end up pressing them together (the 1/10) chance

[@grabir01]

Hi Tanin. I just did my SC400 with not much joy. Before install, only the Tac and Temp worked. I installed all 4 needles and now only the Tac and Speedo work.. Sort of.. Only around 1/4 inch of length is illuminated and the short needles Temp and fuel have nothing. All were tested with a 9v battery before install and tested good. Car is a 1992 SC400. Did I order the wrong LEDS? oh nooo....I did a 93 SC300 and it worked great. I would think the 92 SC400 is the same as the 93 SC300.. or? Help!!

[@grabir01]

I checked what I bought and now see I bought the 1994 SC400 LED Needles!! O no!!! Are they different? That much different? Help!!

[@grabir01]

Called Tanin. They told me the difference is polarity. That is a huge difference! I can fix that. Will reverse the leads, reinstall and let everyone know how it goes.. :)

[@grabir01]

ok.. Reversed polarity. It was a pain, but did the trick. Thanks Tanin.

[@TaninAutoElectronix]

Hello! Can you send us some more information about your vehicle so I can see if we can help? 262-456-4147 [e-mail]

[@notyou6950]

What if my speedometer don't work right? Mine only goes up to a few miles per hour and stops there.

[@TaninAutoElectronix]

We can help! Send us a message with your vehicle information and we can get you some repair pricing: [e-mail]

[@grabir01]

Are your boards dimmable, same as factory? Also.. Only the short needles need glue gun glue to balance them on the sc300?

[@TaninAutoElectronix]

This video should answer your question :) kzbin.info/www/bejne/j4OonKeXhteLZ8k

[@McModz310]

I recently changed the LEDs in speedometer and tachometer for my 06 Lexus is350. But my speedometer needle only moves on startup, it doesn't move while driving. Would you know how to fix this?

[@TaninAutoElectronix]

Hey! For an issue like this, we usually can't diagnose the problem or make recommendations without seeing the unit. The best way for us to help would be you sending your instrument cluster to us for test and diagnosis. You can view this service on our website at www.taninautoelectronix.com/product/general-diagnosis-service/ Also, we apologize for the late response, but hopefully this still helps you out!

[@LunaDiego5]

are es needles interchangeable with the sc?

[@TaninAutoElectronix]

Hello Diego! Please reach out to us with your vehicle information and we'd be happy to provide you with some fitment information! 262-456-4147 [e-mail]

[@jflower702]

My dealership wants about 3,000 to fix this. I live in California. Where can I purchase this from? I'm not sure if this is a reasonable price!

[@TaninAutoElectronix]

We can get your instrument cluster repaired for much less than that quote ! Check out this link for information on the repair: www.taninautoelectronix.com/2006-Lexus-IS-F-IS250-IS350-Gauge-Cluster-Repair-p/is_cluster_repair.htm and give us a call at 262-456-4147 at your earliest convenience and we will get you set up for our repair quickly and while saving you thousands in repair costs that you don't need to spend! Thanks for contacting us here. We look forward to helping you out soon.

[@5818fa1]

I will fix for only $2500

[@jameslewis3175]

Where do I get needles for 95 Lexus es300

[@TaninAutoElectronix]

taninautoelectronix.com/product/tae-1992-1996-lexus-diy-needle-boards/

[@DR.ELEKTRIK]

Can anything be done to the is300?

[@TaninAutoElectronix]

Send us an email to [e-mail] with your year and issues. We would be happy to speak with you about options if we can repair them!

[@peterk4134]

Yes and no; the process of removal is half the problem before you can get to the pointers. Typically my new acquisition also has failed lights. I will be doing this sometime; no hurry BUT I may just use painted on fluorescent paint using a fine brush.

[@LunaDiego5]

or how about the ls

[@TaninAutoElectronix]

Unfortunately the LS, SC and ES are not interchangeable needles.

[@jflower702]

It's a 2007 is 250

[@TaninAutoElectronix]

We responded on your first post with the information on contacting us. We are happy to help you out!