Installation of KOSO heated grips on the Husqvarna Norden 901

These items on Amazon
Koso Grips - amzn.to/3xVlmWh
Grip Glue - amzn.to/3rdo8SV
Above are my affiliate links and I will receive compensation if you purchase through them. This video is a very detailed step by step installation.

[@thomaskist3287]

Great video! Best one out there on the Koso Grips. Very good that you show every step very clearly! Great visual story telling. Keep up the good work!

[@depechemoto]

Have them on my Svartpilen 401- game changer!! These are the hottest grips on the market from what I've been told.

[@bigmikes901adventures]

Great video Michael as always. A terrific alternative to the pricey stock ones and so easy to power up and select a comfortable setting....I think I'll get the same if available in Canada!

[@roblepack]

Good video. I did the install a few years ago on my 890 which is basically the same. I chose to remove the conical plastic on the the throttle sleeve. A bit more grinding but you end up with a flush fit.

[@adriandegifis]

thank you for this very helpful guide!

[@b3n926]

Great Video, nice and clear with good camera work

[@jimkonugres8454]

Just installed grips, this video helped tremoendouly. I just have a comment based on MY EXPERIENCE(S)...I put the left one on using mild grip glue on the handle and a little in the grip. Until this installation I have never used any type of grip glue on any grip install. The LH side was very tight and had to use a mallot to finish getting it on. There was still a bit of a gap at the end becasue I could not get the grip on that last little bit. Not great, but YOU ONLY HAVE ONE CHANCE TO GET IT RIGHT. On the throttle handle I decided NO GRIP GLUE so I lubed the grip and the tube with dishwashing soap (have done this in the past with no issues). The grip went on perfectly with little effort. I did need to trim the end of the grip due to the conical shape the throttle tube at the thumb-end of the grip not being able to get the grip all the way up the tube. Unavoidable. Wish I would have just used the soap on the LH grip to avoid the gap, but oh well. I can live with it. I did not even break out the directions. Thanks for the time you took to create the video.

[@bpositive8551]

I did a test fit on my throttle side and also noticed it got harder to push on as it neared the end. Using calipers I confirmed the diameter of the throttle tube increases. I used the 'draw' technique from the video to whittle it down until the tube was about 1-inch in diameter all the way along. The grip was a snug fit and took a lot of effort to remove it, twisting it back and forth helped. I haven't installed them yet as I was undecided on the glue. I think I will take your advice and not use any glue. If I have slippage I should be able to remove them and reattach with glue.

[@jimkonugres8454]

@@bpositive8551 I thought the same thing (slippage) you wont have any, it is a very snug, tight fit. The grip glue made it 10x worse. Good luck.

[@bradleyolenik8279]

Great video!

[@scottporter0069]

Very nice.. Thank you.

[@netkongen]

I used hairspray to get them on.

[@ssmith278]

From this video, it looks like you don't have to install a relay with power coming from the battery. Is this correct?

[@thaspaniard]

Thx for the video! I've got a set I'm about to install on my bike and was wondering how you like them. Hot enough? Does the switch interfere with operating your turn signals?

[@nordenamerica]

They work great! Plenty hot enough and no interference with the turn signal operation. I'm very happy with them.

[@thaspaniard]

@@nordenamerica Thanks for the response! That's good to hear... I'm really looking forward to no longer needing to pry my frozen fingers from the handlebars.

[@jimkonugres8454]

I installed the location based on this video. The positioning is perfect from the video, I recommend the same locations.

[@george1984]

Is your turn signal show warning code?

[@nordenamerica]

I got no warning codes. These installed with no problem and still work great

[@cezzar5552]

Klej trzyma jak go nima. Za dużo kleju.