Installing 2007-2017 Jeep Wrangler 4-inch X-Series Suspension Lift Kit by Rough Country

www.roughcountry.com/jeep-susp...
Easy bolt-on installation
Increased ground clearance
Levels the front with the rear of the vehicle
Front adjustable track bar is made of forged solid steel for unsurpassed strength and durability
Coil correction plates correct the rear coil spring angle by 10 degrees, allowing them to function more effeciently.
Includes our High Performance 2.2 series shock absorbers.
X-Flex control arm features:
Clevite brand OEM style rubber bushings.
Flex joints are fully rebuildable.
Flex joints feature a massive 2.5" diameter body and 1.25" thread.
Fully greasable.
Adjustable retainer ring.

[@brianfedie8046]

Why is he installing the control arms with the grease zert pointing up? :-(

[@CavemanOutdoorsMissouri]

Does this lift require a exhaust spacer?

[@AZOverLandOffRoad]

Why are there no bump stops? Using the factory bump stops with 4 inches of lift?😮

[@Raynolasco9090]

Would I have to adjust any on a wj?

[@claudiagamino6499]

Just finished installing, the rear driver side shock rubs against track bar braket. Anyone with same problem.

[@Z28Z28SS]

Show us the end result

[@takingu2skoo]

need help here...... so I put the lift on and it is great but I have 1 problem there's a electric wire I think its for he brake sensor ??? and it broke when I flexed how to fix it? and can I make it longer is there a fix like the brake line ?

[@RoughCountryTV]

Did it happen during the install or while off roading? If it happened during install sounds like you might have dropped the axle too much and maybe caused it sever the harness. This can also happen when flexing. You will have to replace that with a stock harness and make sure it's clear of pinch points. Other than that it shouldn't have to be extended.

[@mikebike77]

There are some other components that you guys have totally neglected to include. Like the drag link relocation bracket and correction plates and the fact that you have to cut off a bolt and replace and a couple other small things but other than that pretty strait forward.

[@RoughCountryTV]

+mike bike Thanks for the feedback. This video was filmed and uploaded quite some time ago at this point and is due to be updated. We recently filmed a new JK 4-inch X-Series install video, but have yet to edit and upload it so be on the lookout for that and we'll keep your suggestions in mind when editing it.

[@kittysch2]

Rough Country ..... Are the Measurements for the RC front control arm set and the rear control arm set a must? So is there a chance that I may have to adjust any upper or lower for a 3" or 4" JKU lift? 35" T.

[@Greivous429]

Rough Country must have just changed the title, because it has 2007-2017 jk but the video was uploaded in 2014

[@crkaiserman1442]

YOUS MUST SHOW the final result.. OFF COURSE!!!!!!!

[@javierbarroso23]

RC can't find a step by step 3.5" series 2 JK install. got my lift in the way. if you can send me in the right direction would be helpful.

[@RoughCountryTV]

www.roughcountry.com/catalogsearch/result/?cat=0&q=JK+Steps This is all that we offer for steps for the JK.

[@nicholaspaque7838]

I have a '15 JKU with cut fenders. Can I run the 38" Patagonia with this lift?

[@RoughCountryTV]

35x12.50 would be max size on that one.

[@WILFRIDO1217]

why this lift not incluided the bump stops?? dont needed

[@RoughCountryTV]

Bump stops are not required for this kit.

[@kharishh7028]

how can I know that my jeep is adjustable for the lifter kit or not?

[@RoughCountryTV]

What is the make and model of your jeep? All jeeps are capable of being lifted.

[@kharishh7028]

the model of my jeep is 1990 and i just want lift my jeep up to 4 inch and make her wrangler .whats about the front bumper can i make it by hand through steel>

[@JCsWorlddd]

How much the labor would be? Hours it’ll take?

[@RoughCountryTV]

4-6 hours on this install.

[@thinkclear3834]

Is this a good lift kit ? Please let me know I would like a honest advice

[@kswan23]

Looking at the same life.... I'd like to know this as well. No responses.

[@thinkclear3834]

@@kswan23 🤷🏻‍♂️ I don’t know bro . I just want to know a good opinion that’s all

[@jewdichop]

do you have to replace front drive shaft with this lift????

[@spartanlegit1]

I believe so

[@talihtalih1943]

jewdichop I think its required for higher lifts

[@RoughCountryTV]

+jewdichop See the notes on the product page: www.roughcountry.com/jeep-suspension-lift-kit-674x.html On Automatic equipped vehicles; due to use of an oversize driveshaft from the factory and inadequate factory clearance it may be possible for the front driveshaft to come in contact with the automatic transmission pan tearing the factory boot and rubbing on the shaft. Generally this occurs during heavy articulation when front sway bar links are disconnected and longer shocks are installed. If this is found to occur, the proper procedure would be to replace the oversize factory shaft with an aftermarket smaller diameter shaft to increase clearance between the transmission and front driveshaft. Rough Country does offer this driveshaft if needed.

[@RoughCountryTV]

+jewdichop It's not absolutely necessary... but HIGHLY recommended.

[@benjamin8674]

Is DIY installation advisable on this kit?

[@RoughCountryTV]

Yes this kit is able to be installed by a novice and comes with step by step install instructions.

[@benjamin8674]

Thank you for your reply. I’m getting one.

[@jparks888]

have one for the tj with the 4 inch X-series?

[@spartanlegit1]

Tjs and cjs suck dude get a jk

[@kevinv1370]

+spartanlegit1 TJ's and CJ's don't suck. Any Wrangler is badass.

[@RoughCountryTV]

+Jacob Parks www.roughcountry.com/jeep-suspension-lift-kit-661.html

[@AFcody16]

+spartanlegit1 not a true jeeper.....

[@jungleboyx141]

will this fit a 2 door jeep?

[@RoughCountryTV]

No, but this will: www.roughcountry.com/jeep-suspension-lift-kit-673x.html There's also a 6-inch: www.roughcountry.com/jeep-suspension-lift-kit-684x.html

[@jungleboyx141]

thanks

[@RoughCountryTV]

You are welcome!