Installing a Hurst shifter on a Challenger! Love this mod!

[@TexasMadeCruz]

Good video bro. I appreciate your time, detail and genuine commentary. About to try it myself right now

[@alveyjohn]

My friend, this was a great video. You do it slowly to prevent damage to the console. This is good info.

[@duaneahnert6409]

Good job! Loved that you included the whole process. Most videos just show the b4 and then the finished product. Great mod too looks so much better than the original!

[@beyondthedetails]

Thank You! I appreciate you

[@socalfun64]

Every Engineer who gets stuck in the design of clips and fasteners departments, gets their revenge on us diy folks. Either 50 different Engineers or One really angry guy makes each one unique and leaves US with no idea how to remove the myriad of different designs. The bane of the diy Car enthusiasts, lol!

[@timchange5073]

American Muscle has an install video, would've saved you a bit of aggregation. That was painful watching you struggle.....but you did it !!

[@borri68]

I just messed around by trying to break the plastic loose. There is no reason at all to break the big console piece loose. All you need to do is pinch the plastic section between the boot and the small coin/key tray. Then pull up with enough force to create a tiny gap at the back of the boot plastic part. Then slide a thin plastic pry tool (see harbor freight) into that gap. Then use one of the other pry tools and slide the tool to either corner. Then use the one that looks like a crowbar and pop it up on the corners.

[@borri68]

Just watched again. I didn't realize the coin thing comes out. That would be easier than pinching. At 2:56 you had that tiny gap needed to slide the prey bar under.

[@marccamacho8551]

this might be a stupid question, but why do you have to leave the old shifter in the car under the console

[@LRHNCash]

So it can read properly without that being plug up the transmission can’t send a signal to what gear the car is in. And you will get service shifter on your dash and sometimes the car want go into drive or reverse if that’s not plugged in.

[@beyondthedetails]

Yes

[@beyondthedetails]

@LRHNCash Thanks for the clarification for him!

[@tt-rs1457]

Looks very good ! But it doesn*t iluminate, does it ?

[@Dwillztx]

Nope

[@marccamacho8551]

@@Dwillztx this might be a dumb question, but why do you have to leave the old ship knob in the car under the console?

[@Dwillztx]

@@marccamacho8551 No worries! Its to maintain OEM functionality. To my knowledge there is no electronics in the Hurst shift knob.

[@pacocalvillo4236]

Are you able to move the gear selector while the vehicle is off with the Hurst handle?

[@macfrost74]

that's what I'm wondering

[@Frizzlefrail]

Love mine had it for about 3 years

[@Sumbuddysumwhere]

Did the trigger end up doing anything once you hooked it up?

[@beyondthedetails]

What do you mean?

[@Dwillztx]

@@beyondthedetails hes asking do you have to press the button to shift (like stock) or does it move freely without pressing the button (like auto without button).

[@beyondthedetails]

@@Dwillztx You have to push the bottom ofcourse. This is made for auto.

[@beyondthedetails]

This was an easy install. Took me about 45m-1hr only because I was recording and then as I said the camera died. Blessings

[@kenb.8596]

Looks Gr8 for bling, but your video talked me right out of it watching the install, I would have tossed the $300-dollar shifter in the trash & went to my closest watering hole & started 12oz curls, one after the other calling myself one dumb mother f**ker for wasting $3 hundo on stupid bling, jus sayin!!! Gr8 video & again, thanks for saving me a meltdown, I'm already one blade of grass from being insane, LOL

[@Dwillztx]

I have no idea why it’s 300. Seems crazy over priced.

[@dchachacha5663]

The oem piece costs over 800

[@manonamission2000]

I'm concerned a p.o. might mistake it for something else, based on its design... otherwise it's bad-ass

[@uniquecrystal1456]

Bro yo car sound good what do you have. I have same car lol

[@lawrencetobin7050]

Looks like a real pain in the hurst

[@lsu1992]

WARNING: The factory boot is shidt. Very thin leather, very dry, and will split/tear easily. I ruined mine installing this Hurst, and hand-sewed a new one based on the factory pattern. ...And after zip tie/set screw, shift into D before snapping the boot clips into place.

[@Deadman_Elit3]

Great video man! I went along with you and got mine installed! 🤘🏻🫡