Installing (Battling) a Dumb Amazon Faucet

[@theabhominal8131]

love that you left the mess up in.. best way to teach is to show mistakes being made.

[@StudPack]

Thx 👍👊

[@stephensaines7100]

The screw worm-strap type clamp is superior in many applications, but as well as being able to over-clamp and crush the tubing, it can pinch the flexible hose being clamped, making it leak. Over-tightening any clamp usually ends in failure.

[@Skatesoldier24]

I love how you guys leave in your mistakes and show how to correct them. This is the best way to show others what not to do because we can actually see how it went wrong. Newer subscriber but I'm already hooked!

[@ericfraser7543]

What do you mean? they didn't fix the problem, there is still no main to the home... they should have installed a main shutoff and replaced those angle shutoff valves rather than hacking in the sink connection.

[@Skatesoldier24]

@@ericfraser7543 He states in the beginning that the main's location is unknown. Also, the mistake I was talking about clearly is the hose clamp on the hose. The problem was that he crushed the hose and it leaked. He reshaped the hose and put the correct clamp on therefore fixing the problem that was referred to. The sink, dishwater, and refrigerator are all working properly. No need to be a troll.

[@ericfraser7543]

@@Skatesoldier24 Ok call me what you want, it is still a hack, someone still needs to deal with the main or deal with a flood and then the main... it is code to have a shutoff where the utility enters the home and the utility knows where the main is located, they have locators which can find the location of the main at the street, they even have the means of installing a shutoff if none exists. FYI, in many jurisdictions a plumbing permit is required when a fixture is replaced, which needs to be pulled by a licensed plumber unless you are the homeowner doing the repairs. A licensed plumber does not even start that repair unless he finds a main shutoff, imagine his liability if he were to break that line or the valve were to fail replacing that fixture.

[@Skatesoldier24]

@@ericfraser7543 I understand all that but that was not what my original comment was about. The point of my original comment is that I appreciate when people leave in their mistakes for others to see.

[@ericfraser7543]

​@@Skatesoldier24 sure I appreciate stud pack owning up to their mistakes... BTW I am not a troll, I think my comment is productive, even negative comments count toward the "Google algorithm"... so Stud Pack gets paid for my comments and then your responses... essentially it pays to be controversial on youtube! They just posted a video where they were called out for not pulling a permit and got a ton of hits, I give them props for owning up to it and posting it...

[@vettepwr23]

Just came across this channel. I really like how they share all the details with you. A lot of others hide or don’t share when they run into issues. This guy could have is own tv show. Very good at explaining and keeps you engaged at the same time.

[@nroman1977]

Two advantages to the spring clamps: 1) They offer even pressure around the entire tube. The ones you used can cause the rubber boot to stretch and pinch to one side causing a leak. 2) The maintain consistent pressure despite thermal expansion and contraction. Not a factor in a dishwasher drain hose but in some other applications thermal expansion can cause the other clamps to cut thru the boot over time.

[@htownblue11]

Nothing was a “standard” install on this project. Thanks for showing people that adapting as needed isn’t too difficult as long as you go step by step and change as needed. You mention a few minor but important details which is so fantastic for those just learning…..The high loop for the dishwasher is critical to allow dishwasher drain pump function.

[@StudPack]

Thx TJ 👍👊

[@waldogtv5486]

I've installed several dishwashers as a home owner, never heard of the high loop until now. Guess I have some homework to do, but my current dishwasher I installed 11 years ago is still working fine?

[@crookeddonald4761]

@@waldogtv5486 High Loop helps prevent dirty water from sink drain backflowing into the dishwasher. I do it on all my installs.

[@AKJammer1]

@@crookeddonald4761 ​ @Waldog TV It's code in most locales. Some places need the vent, but a high loop will usually pass.

[@billm6171]

There's someone else stated I had never heard of the high loop either, good information to know

[@DaddyBeanDaddyBean]

+1 for leaving the mistakes in. It makes you guys more human, and makes us DIY'ers feel better when our projects don't go perfectly. Tip for installing those strainer baskets - put the putty in there and tighten it down really well, and give the putty a minute or two to squeeze out. Then tighten it again. Give it a good 10 minutes - perhaps finish the rest of the install - and go back & tighten it one more time. You'll only get a little bit more of a turn this third time, but it **really** locks it down.

[@StudPack]

Cool tip thx 👍👊

[@richg3411]

We donn nee no manufacturer's recommended clamp...let's use the manufacturer's recommended clamp. LOL! Great authenticity on real-world miscues. Keep up the great work!

[@lakecityransom]

We all assume the manufacturer is trying to give you cheap junk and usually that is the case. lol

[@jaywmeinen]

I LOVED the camera shot through the sink drain! I literally laughed out loud! You guys are entertaining!

[@sarahdeshay1394]

Well done, especially appreciated the “purge” of the line to avoid clogging the faucet end.

[@NoL0NGERhumAn]

Its also good to purge directly from the angle valve first especially when plumbing work has been done on the water supply because depending on the faucet debris dont only get caught / stuck in the aerator but also inside of the valve cartridge it self. I just use a old supply line and flush a couple gallons into a bucket.

[@morrisjvan]

I couldn't take my eyes off the professional looking cut outs in the back of the cabinet for the plumbing and electrical fixtures!

[@ryan2587]

Regarding screw type hose clamps. They are not good because the hot water and the cooling of that hose will cause those clams will loosen over time. The spring type clams will "self adjust" with the expansion and contraction of that hose. I know this because I was a auto technician for 10 years. On radiator hoses these clamps always leak over time. Love the channel!

[@StudPack]

Good stuff Ryan!! 👊🏼👊🏼

[@dallasarnold8615]

On a totally different subject. Yesterday I came across a roofer's comment about striking lines for aligning shingles. Both persons holding the line holds a chalk box, but you attach the loose ends to each other. One guy walks out pulling out the line from one box. After popping 2or 3 lines the one holding the extended line reels it in and as he does it pulls out the line from the other end saving the time and effort of walking back and forth. Really makes me feel like a rookie not having thought of that myself. And I never saw anyone else to it either. Duh !

[@mikeyb3743]

I always enjoy your videos. When you don’t edit out mistakes I appreciate it even more. Thank you for quality content and keeping it real. I can see myself making some of the very same mistakes. I appreciate your excellent explanation and attention to detail. Great work.

[@jamesoneil7768]

JUST AWESOME, Guys Paul you are becoming legendary to be able to work under that sink and explain everything you are doing so precisely and clear is just amazing and all with a smile. THE HANDIEST MAN IN THE SOUTH

[@StudPack]

Thx James 👍👊

[@clarencegreene9932]

Ditto on all the other great comments! Just want to add one thing - love the father/son relationship. Not to be taken for granted! Thanks, both of you! PS - from a 40+ year video professional - great camera work! Again, not to be taken for granted

[@thomaswilliam630]

Renovations are so much tougher than new builds....Love that you guys enjoy your work...thanks

[@drewwade9640]

Like many other viewers, I to appreciate you not deleting mistakes, and then explaining what/why it was a mistake. Whenever I'm given a work assignment and told "should be a 15 minute task", it never is, because of a host of other issues. I enjoy your videos because of your thorough explanations. Thinking not only of the moment you're in, but how it affects future work. Keep up the good work.

[@donaldhollingsworth3875]

I liked the you chose to use the stainless steel braided line. My house was built with the stupid plastic supply lines which I changed over right away. I also put a pigtail on the garbage disposal, then I surface a electrical box in a top corner of the cabinet with GFI outlets & plugged the garbage disposal & dishwasher into. I also always use the white plumber's paste ( I don't recall the proper name of is off hand) on all the PVC connections under the sink then clean off the excess with paper towels for a more waterproof seal. I also ran a stainless steel braided line to the dishwasher. I like to use the blue PVC cement since you don't have to use a primer with it. I the blue PVC cement on all of my water lines for my irrigation system a not one failure in over 21 years. Keep making great videos. I learn a lot from them.

[@StudPack]

Thx Donald 👍👊

[@Stuart68505]

There might be an insert of brass were you could reinforce the dishwasher drain hose where it collapsed under the stainless steel clamp. This was a helpful video. I liked the 45 degree addition to line up the drain pipe to the house. Thanks

[@DrD6452]

It's exactly those types of mistakes that you and all your viewers get to learn from. Your videos are as much educational as they are informational and entertaining.

[@wileycoyotesr8623]

No runs, no drips, no errors. (that weren't resolved) Nice work. Excellent videography.

[@StudPack]

Thx Wiley. Man I loved that cartoon when I was a kid 👊👍

[@safyany9191]

You have a lot of experience, you are a simple man who simplifies things and a brilliant teacher

[@StudPack]

Thx my friend 👍

[@tonychan4526]

I love the eff-ups during the installs....just like real life! Thanks for showing us how to adjust to problems as you go. Great series.

[@StudPack]

Thx Tony 👊👍

[@Vrplumber]

When installing the "add a tee" fitting on the anglestop, I would use a backup wrench on the angle stop to reduce the amount of strain on the 1/2' copper pipe.

[@kenmore01]

I know! Unfortunately, you need three hands at that point.

[@throttlebottle5906]

sounds like someone that's had a line break off/blow before. (I know nothing of such) 🤣🤣

[@estephanina]

23:15 my husband installed our new insinkerator last weekend and suggested to me to do the exact same swap out. I almost said "Go for it" but thought, for some reason they shipped it with the spring clamp so I suggested sticking with what came in the box. We haven't had any leaks so far! I'm so glad you all kept that in the video because now I have learned the lesson of what may have happened otherwise.

[@boelie2001]

Love your videos for leaving in your mistakes. I think the proper way to test for leak is to dump a bucket of water at once in to the sink. When you only turn the faucet on, it might not be leaking where as you dump in a bucket it might. I had once replaced part of my drains in the kitchen and tested with only a running faucet. Worked great. As soon as my wife dumped in a bucket of water it was leaking around the sink-thingie part. It did not show with only running water from the faucet.

[@jassonhoskins367]

I appreciate your common sense and real approach to your work and the videos you produce! i enjoy watching you guys and i really like the bond you have with your son! thanks for the content!

[@StudPack]

You’re welcome 👊

[@martinmoss317]

I always called those screw close hose clamps "jubilee clips" in the UK. you can add that to your international vocabulary along with pipe olives.

[@jamess1787]

Funny, I always have called them hose clamps from plumbing... But they're used in other industries as well: and most non-plumbers call them either gear clamps or worm clamps....

[@PJBonoVox]

Yep, I rarely ever hear them called anything other than jubilee clips in the UK.

[@ModelLights]

Ah, 'A Jubilee Clip is a genericized brand name for worm drive hose clamp'. Had to look it up, but just a genericized brand name like Xerox for copier so it's completely arbitrary. Thought there might be some more direct reason to relate it to 'jubilee'.

[@northernlightsrenovations1710]

Canada eh? I must admit that I'm just a wee bit jealous about your winter weather down there. It's already getting cold here, and within a few weeks I'll be needing to take all of my fluids, glue, silicone, etc. out of my truck and trailer every night to prevent freezing. It's just one more pain in the kester with the colder weather here in Canada. Love you guys, and love watching your subs grow day by day. Keep up the great work!

[@gsh319]

It doesn't matter how long you've swung a hammer, you can always learn something working or watching other guys. Thanks as always, and were all smashing the like button.

[@thaitichi]

For something like a dishwasher drain the screw type clamp will work itself loose over time due to the temperature fluctuations. Spring type clamps always adjusts itself. Keeping that mistake in the video will help a lot of people I'm sure. Nice job Stud Pack!

[@StudPack]

Thx 👊👍

[@number1pappy]

Best plumbing advice came from my father in law who was a plumbing contractor. The first thing he said to never forget when dealing with plumbing is ,"Craps rolls down hill and never ,and I mean never chew your finger nails"!! Lol! No but ,seriously he said ,to always assemble all your faucets and connections before you install your sink"! He was correct! It's so much easier to install your faucet and deal with connections with the sink out!

[@rjbroderdorf9053]

First 3:00 minutes I literally learned 5 different bits of valuable plumbing/piping/fitting info! I really appreciate the easy to follow and straight forward presentation, especially those little tid-bits and details usually only learned by experience (i.e. making your own mistakes). It's a vary rare ability to teach, include details, make it easy to follow, all while making it both interesting and entertaining! Add the excellent camera work making things easy to see and the often under appriciated video editing style, and Stud Pack has one of the most professional looking, as well as personable and informative DIY channels around!

[@markg7963]

Paul, you are an exceptional instructor and communicator. As always, great video!

[@StudPack]

Much appreciated Mark 👍👊

[@MatthewPierce9]

Love these videos. Thanks for not cutting out the dishwasher leak.

[@themrnorwood]

Yo the hose clamp segment is top shelf content. I typically use the o ring style hose clamps too “for strength” but this was a great lesson for anyone in the trades or diy’er

[@CoolSteve77]

I absolutely love how you guys include mistakes / f-ups and don't edit them out like everything always go perfect. Great channel!

[@milesharlan1]

Sundays are even better when stud pack has a new video..keep up the good work

[@tompeters4234]

Nope.

[@kenmore01]

Cool vid! Yeah, I have crushed plastic fittings in my job. Nothing wrong with that hose clamp, you just need to be careful. Then again, nothing wrong with the other hose clamp either. I saw the drip from the hot water line early in the video. I hate those angle stops. The gate valves just suck. Thanks!!!

[@StudPack]

Thx Ken 👍👊

[@mimimitchell8551]

Love watching you Guys work. I've been binge watching a bunch of videos. We are starting a new garage build with an apartment above it this spring. Much like your stud pack dream home. It's interesting to see the differences in build between an Eastern Canada build and a southern US build.

[@SME_Ste]

We had a new bathroom tap to use which had a 3/8 compression on one end, luckily they supplied the adaptors to 15mm pipe. Uk based here. Usually 1/2 and 3/4 inch in the UK. Just found the channel, and liking it guys!!

[@waynejanik9668]

Thank you for sharing and your honesty in your videos. Watching your videos is like going to school and learning a new trick of the trades or a work around a difficult challenge presented by well aged builds. It is great to see that even a pro can make a mistake and not cover it up. I would agree with you to use the hose clamp over the compression clamp, but I guess in todays designs and use of cheaper materials using what comes with the product is the best. Lesson learn for everyone. Keep up the great work and sharing all your knowledge with us.

[@StudPack]

Thx Wayne appreciate the comment 👍👊

[@christopherpenn1326]

You guys must have a lot of "Binocular Bobs" watching ;). Don't let them get to you. Some people are unsatisfiable. If it looks good it is good. There is also such thing as good enough as long as it is a durable repair/installation. Great videos guys. I enjoy watching them.

[@StudPack]

Thx Christopher 👍👊

[@gort5583]

Really enjoy watching you guys work as you give a lot of good advice and show just how flexible and resourceful you need to be when working on a house.

[@KennyX1967]

I always used the plumber’s tape on the metal thread but you showed me that it is not needed. I am going to try that the next time. Great video. Keep up your amazing work.

[@robertlee7666]

Love that you left in you're mistake! Makes us all feel a little better about our jobs!

[@StudPack]

Thx Robert 👍💪

[@Wolfburns]

Indoor plumbing and water problems in general are my biggest home owner fear. Watching this gave me one less place I have to be afraid of repairing now. Thank you so much for your amazing videos!

[@joeoliver9043]

Your hose clamp mistake was the most educational part of the video, so it’s great you left it in. If I hadn’t seen you make that mistake, I guarantee I would’ve made it myself eventually. Now I know better! Thanks!

[@StudPack]

You got it Joe 💪👊

[@markphillips6154]

When you’re working under a sink like that get an old ironing board and takeoff the legs and put the ironing board pad on it and stick it under there and lay on that thing and it’s really comfortable for you

[@flubber27100]

very real life with the small leak at the end. My heart is always in my mouth when I turn on the water after something like you did. huge sigh of relief when its not leaking. Great video guys

[@Lierofox]

Something to consider with those hose clamps. Spring hose clamps = Constant tension No matter the heat cycling, vibrations, changes to the hose with age, etc., it'll always apply the same force to the hose. Worm gear hose clamps = Constant diameter The force applied can change based on temperature and flexibility of the hose, and it can be tough to apply even pressure. Worm gears can be MUCH more convenient to use though, they've got a much larger usable diameter range, big advantage over spring clamps there where they're designed for a very narrow range of diameters they'll clamp down on. Been watching a bunch of your videos in the last week or so, been learning a lot!

[@lorneh8642]

great video. key step to take the spray nozzle off and purge trash from the line. I learned that lesson the hard way.

[@stephenecamp200]

I love the Kid! He reminds me of The Boy Wonder, "Robin". From the 1966 Batman TV show. He's a great sidekick that makes me wonder sometimes if HE isn't the one who is REALLY in charge!

[@mnwlindsay]

Just ran into your channel a few days ago, been watching a lot. You guys have some great tips and ideas, and neat to see how the pros do it. I love that you keep your mistakes, oopsies, and hard jobs included. You don't try to pretend your perfect, that helps me learn some of the right and wrong ways to do things. Love you guys. Keep up the great work.

[@steelbak-customs]

This is so helpful. Non of this is rocket science, but its hard as hell to do a lot of this if you haven't seen it done and explained like this. Thanks a ton.

[@MtnBike60532]

I'm an insurance guy. The most common cause of water damage claims which I see is failed compression fittings. I avoid them whenever possible. Excellent instructional video! Just the right amount of detail without much wasted time.

[@StudPack]

Thx insurance guy 👊👍

[@par3me]

Whet would you use instead of a compression fitting for a supply valve? Are you seeing this because the compression ring failed? Or the valve wasn’t maintained and replaced? Greatly appreciate the info.

[@MtnBike60532]

@@par3me Threaded over compression - "when possible." My thought is the failure is a result of improper installation more than anything else. Often DIY homeowner. But, one multi-million dollar loss was the result of an 8" water main compression fitting supplying a high-rise office building. It failed and flooded the basement just a few weeks before completion. Obviously, this wasn't a DIY job. But, it still failed and would have been more secure if it included some type of mechanical fastener in addition to the compression fitting.

[@leebannister3759]

I had the same faucet fail its fittings so badly we had to fine tune the compression until the leaking stop... Only to find out the faucet couldn't handle the touch shutoff 'hammering'

[@dallasarnold8615]

WOW ! That is a shocker to me. The only time I have ever seen a compression fitting fail is from careless installation. It just takes a couple more seconds to do it right. I am retired now, but did handyman work for 40 years and never had one fail when I did the install. Maybe I am just that lucky though.

[@andrewnovino5269]

I Like that you showed even you screw up it shows even the pros have a lil trouble here and there it's all about trial and error thank you for these videos they give me new ideas sometimes

[@sraike]

You guys are amazing! Your work ethic and attention to detail are second to none. Thanks for another great video.

[@dankelley9361]

Great instructional video, nice to see someone, beside myself, struggle working overhead & in tight spaces!

[@StudPack]

Thx Dan 💪👊

[@DaddyBear3000]

Ha, thanks for reading my comment about the olive. I’ve installed the same tap with a Brushed finish. That click connect fitting for the head hose leaked after about 18 months. Make sure you give the head a good tighten as well, if it comes loose the water will shoot up the arm and soak underneath. Two clients have had this issue.

[@BRICEN18]

My sink plumbing was the opposite issue. I needed compression to npt. I ended up ordering a fitting off amazon that was a direct adapter from pipe to compression.worked like a charm. Couldn’t hurt to have a couple on hand for future jobs. Have a good Sunday Stud Pak!!

[@karenmitchell6814]

I always learn something new watching your videos: straight and tapered pipe thread; I had no idea.

[@StudPack]

Cool thx Karen 👍👊

[@user-ml8bw3pd1o]

I have installed 5 of these faucets in rental units. Every one of them has came with 3/8" adapters to attach onto the 1/2" fittings. All of the faucets have worked flawless for over a year now. First one took me a little time to install, but the subsequent ones have been 15-30 minute jobs depending on if I have a problem getting the old faucet out. Only issue I had was one faucet had a cartridge leak right out of the box, but amazon sent me a new one in one day so it was hard to complain. Sorry to see that yours was missing the adapters, but its good to show a real world scenario of how to modify what you got if you need to make an install that same day. Love the content, keep it coming.

[@russmelton5684]

Great video! The "mistakes" teach a lot more than everything going fine. I've encountered all the challenges you showed over the years.

[@JuliaNeubauer]

Jordan, your closeups are great-they make all the difference in demonstrating the task at hand. 👍 Your dad will be your hero for life; his work ethic/attitude is a blessing even to this viewer.

[@Phallanx11]

i appreciate when you show us when you goof up. imo, you learn best through mistakes so thx for showing us yours.

[@dancudzilo92]

Love watching you do the job… you make it look so easy !… lol ..I’ve done many of these jobs … between Buffalo NY and Pt. St. Liucie Fl !

[@charleschambers9000]

The contractor that put our dishwater back in with second hose, like you used, used the screw type hose clamp. Did not realize it was leaking for a year after install (tile kept it under cabinets and in studs). What a mess. The contractor would not own up to causing problem, and ended fixing myself (including mold inside of walls). Wish I had seen your video a year ago...

[@levipulizzi2836]

Your guys are motivational, so cool how you guys work together father and son🙌🏻💪🏻.

[@anthonyrendon6293]

I work and explain things just like you do. You’re teaching is great 👍🏻. You guys are a good team. I’m remodeling my kitchen in spring. I didn’t need to watch your video but I stayed watching it because you pointed out every detail. Now I know what an “olive” is “A” 😂

[@Candisa]

23:00 Good thing you caught that, I was yelling at my screen "I hope it leaks immediately because it will eventually". There are a bunch of those spring clamps in my car and I thought they did it because it was cheaper than the screw clamps I've always seen on my older cars. There has been tapped into the cooling circuit of my car to add a heater and an LPG-conversion with the screw clamps and guess what, one by one they all started to leak and damage the ends of the thin wall plastic pipes inside the rubber hoses. Luckily no expensive parts got damaged, but a couple of new Tees and some spring clips later there hasn't been a leak since for years now. Those screw clamps weren't a problem in older cars with metal piping, but those spring clamps are actually better for spreading the pressure nicely all around without squeezing the rubber or the pipe so much it collapses. It's a very common mistake, so thanks for leaving it in for everyone to see and learn from!

[@larryjohnston52]

Really liked the shot of Dad through the sink drain 🤣. So that's how the disposal works?😂

[@bigmike1289]

I learned all about measuring fall bubbles from Shawn over at Gate City Foundation Drainage.

[@StudPack]

I just found his channel recently 👍 good stuff 👊💪

[@edzachary8657]

Another great video guys I love how you show real job site problems and solutions, cuz we all know it happens to us almost daily if it's not plumbing it's electrical and if it's not electrical it's somewhere else, it happens all the time, what I feel makes a good remodeler is being able to problem solve because nothing usually goes as planned, great video guys I love them

[@StudPack]

Thx Ed 👍👊

[@KristiSage]

I always learn something watching Stud Pack! Thanks you guys, you’ve been a huge help with our remodel 🤚🏼

[@b.powell3480]

You mentioned that the water shutoff for that house is about a quarter mile away, and can't be found ! A plumber told me about this special tool that lets you cut into the line coming into the house and install a shutoff valve all while having water pressure in the line, not sure if you can do that, but if so, please do a video on this sort of installation ! I would really appreciate it, as would all of your other viewers, and if I come across that special tool/tools, I will send you some information on it !! Great video !

[@jeffeverde1]

The "special tool" is called a Jet Swet (at your local plumbing supply house or amazon - not at your local big box store). It's an expansion plug on a thin rod that's thin enough to pass thru a ball valve. To work on a live line - slip your new shutoff valve over the end of the JetSwet, cut your line, shove the JetSwet in and flip the lever to seal it and stop the water flow. Sweat on the shutoff valve, remove the JetSwet, turn off the valve, and proceed with your repairs. Or you can prefab a shutoff valve with a copper stub on both ends, and a sharkbite connector on one of the stubs. Prepare the area to handle a minute of free-running water, then cut the line, slam on the sharkbite (with the valve open), and then close the valve. Now you have a function shutoff, you can proceed with your house-side repairs as normal.

[@b.powell3480]

@@jeffeverde1 Thanks for that information ! I kinda knew about this tool, but wasn't sure what it was called, God bless you 🙏

[@iconoclad]

You can temporarily freeze the line with liquid nitrogen while you change your fittings.

[@jmac213stuff]

@@jeffeverde1 Yeah, a jetsweat is mean for a leaky line, not a full pressure line. If you check the rating its about 65 pounds max. For main line, that's risky. You can call your water service provider and ask the engineering dept. what your pressure is. If it's under 60 (can be in the 40's easy). Go for it. Freezing is a better option, Freeze it, cut the line and install a ball valve shut off. Back in business. This is something no homeowner should not have. Terrible job of not sell/recommending and ensuring the proper protocol for the homeowner's protection. So what happened when there is a leak? Client is totally screwed because the 'stud pack' didn't install a code compliant, user accessible water shut-off.

[@jeffeverde1]

@@jmac213stuff If the house doesn't have an accessible main shutoff, you can use a Jet Swet to install a new shutoff - just do it downstream of the pressure regulator. (been there, done that)

[@brendanfisher2528]

I'm a plumber in the UK and these are exactly the connections we have on the tap... I watch alot of American plumbers on KZbin and you have alot of different style of connections than us in the uk..

[@jeffgarner3178]

Thank you so much Stud Pack for showing what really happens. My wife just informed me that our kitchen sink is leaking again!. Kitchen sinks are my nemesis. She doesn't want me to touch it until canning season is over and I am about to replace kitchen cabinets anyhow after we level the concrete floors in a month or 2. So everything is complicated.

[@Thumper68]

I have that same exact faucet bought from Amazon for a great price and the faucet works great for year now. And I’m a water well driller pump installer by trade so I was happy to see those fittings.😂 I like the weight is nice and heavy and easy to adjust so head always goes back.

[@apex007]

If you wanted to use the hose clamp in plastic piping, you can slip in a piece of copper pipe for rigidity (think in terms of a stiffener). Also, the other clamps are similar to those used in automotive settings. They actually apply pressure more equally to the pipe versus a hose clamp.

[@harveylong5878]

we have the same POS faucets at work. close nipple brass 3/4 to 3/4 to yet another supply line was always pain in the ass. so much fun trying to mount and connect those POS's with sink already mounted

[@jameshuffman7676]

I have the same faucet, and went through the exact same pains to deal with it. I ended up doing the male-male adapter, and glad to see I did the same as the pros!

[@timellis9293]

Excellence as usual. If you guys have a pex cutter they work great for cutting the sink drain lines. Just close it enough to put a little pressure on the pipe and then twist the pipe and it cuts through like butter. Just don't try to cut it like pex it will squash the thin wall pipe and give you a crooked cut.

[@StudPack]

Thx Salty 👊👍

[@rodneyanderson1402]

Fantastic, you answered my comment, as long as the outlet is protected by a GFCI via daisy chain it's safe. Had that outlet box been a dedicated circuit it would have needed to be a GFCI receptacle.

[@arghoknot]

The one that I purchased from Amazon, I had it installed without a hitch. The hoses were long enough and they had the 3/8 fitting too. I had the old faucet off and the new one installed in under an hour. I found that using oil filter pliers that I bought from Harbor Freight works great to remove and install the strainer ring.

[@Mobilehomewizard]

I've learned my lesson on Amazon faucets. Only using brand names now.

[@TacoNissan]

Buying plumbing supplies on Amazon is always a gamble lol

[@whattheschmidt]

This. I replaced my leaky kitchen faucet with one that looked great and had great reviews. Well, the leak to the cheap old faucet was on the top back of the handle, this one I put in leaked and sent water underneath and into the basement - not much but enough to really notice one time and I ripped it out, went to HD and bought a Glacier Bay large sink basin + faucet setup that has been great. Would have been nice to only do it once!

[@eddiephillips264]

Only uninformed idiots would buy anything from NEW WORLD ORDER Amazon!!!

[@JasperJanssen]

This tap appears to be made to European standards, it’d all be completely standard size threads over here. (Yes, 1/2” straight pipe thread and all. Don’t ask me, it’s tradition.). Some suppliers think globalization means they can sell anything anywhere.

[@john.french]

17:36 man get one of those 2" pvc cutters!! It's like $26 and no jig or chop saw needed, nice smooth cuts every time so doesn't need much utility knife work either! Great job.. olive comment was awesome as well!

[@StudPack]

Thx John 👊👍

[@ronlovell5374]

Great job guys! You got every detail involved with a standard kitchen plumbing set-up, even with the unstandard faucet. (Ikea special?) 😄 I know dishwasher hoses can be a pain. Sometimes you can get a piece of copper tubing inside the hose end before adding the extension and clamp, makes for a better seal, but best practice is to change the shorter hose out for longer one, if possible? Also as a service tech, I don't recommend the dishwasher connect to the disposal. Yes disposals have a port, but no check valve. When there's a clog in itself or the drain, it pushes lots of crap back into the dishwasher line and can ruin the pump. I've seen this many times, so I like to use a dishwasher Y tie in close to the other basket connection and keep the plug in the disposal. What a great teaching video, wish all the diy'ers would watch this video first so I would have less calls for under sink disasters. LOL

[@StudPack]

Thx Ron 👍. Interesting that you mention check valves. Don’t most modern dishwashers have them at the pump outlet?

[@ronlovell5374]

@@StudPackI wish! This is actually the main reason for the high loop. Maybe some dishwashers specify they don't require it, which would likely mean it has one, but I haven't come across any yet...

[@StudPack]

I was told most dishwashers have check valves. Might be a good video to research and test 🤔

[@ryerob741]

OMG you guys are killin" me...lol I'm wasn't planning on wrecking my free time....but your vids keep me watching for hrs.....

[@StudPack]

😂 thx 🤔👊

[@royfast8439]

Love the humour! Notice the Canadian spelling of humour...! you guys make a great team one mechanical and one technical. Bravo

[@briankowald6465]

Good video. It might seem simple, but there are a lot of connections. I don't know how many of these I have done, but I still watched and learned some things. Glad you used the plumber's putty. Old school and it works. I like to keep stop valve repair kits on hand. Seems like after you turn off a valve that hasn't been used in a while, the old washer and stem packing will leak. Or you get black flecks in the water from what used to the the old washer. About the clamps - I too, used the screw / cam type clamps my whole life and didnt like the quick ones, especially on cars. But one time in the middle of December, I used a screw clamp on a transmission cooler line and it leaked. I had to go back out in the cold a few days later and fix it. I think its because the spring ones will maintain constant pressure of hoses age as well as not clamp too much. One last thing - check the plastic drain connections carefully for leaks, especially the trap since one of the connections is constantly in water. One of mine leaked because there was some "flashing" at the seam. Those parts are cheap, its a good idea to have an extra. Also, the connection from the trap to the wall PVC takes a different washer. One last thing - can't believe there is not a handy shutoff valve for the whole house. What if water starts spraying everywhere from a pipe in the middle of the night? I would dig up the pipe in the yard and put in a box with a ball valve. That would be a good video.

[@StudPack]

Awesome stuff thx Brian 👊👍

[@EMTevjorgensen]

Paul a Class IV boat throw cushion/ PFD is a great back saver for being in the sink box, I use two, one on the edge and one under my hip.

[@StudPack]

Cool thx Eric 👊

[@paulrabbit2011]

Love your videos! Loving the way you keep it real! Paul from 🇬🇧

[@jeffeverde1]

@StudPack - Do your customer a big favor and install a main shutoff valve for them. If you have any plumber friends, they probably have a set of JetSwets (or get just the size you need - they're not very expensive). If you can't buy/borrow a JetSwet, prefab a shutoff valve with a copper stub on both sides (the same size as the existing main supply) and put a sharkbite connector on one end. Prep the area to handle a bit of free-flowing water, then cut the line, slam on the sharkbite (with the valve open) and then close the valve. Now proceed as normally to connect the house-side with your new shutoff.

[@iamamish]

Very nice job guys, it's fun watching you problem-solve. Next stop for the homeowner - they need to get a whole-house shutoff valve installed, pronto! Not knowing where the shutoff is at the street, combined with not having one in the house? Yikes.

[@tompeters4234]

I can't believe you thought the first option was an option. The second option is obviously the better way. I am happy in this video you suggested the better option.

[@tompeters4234]

All weights usually have 2 screws.

[@SeanLeonDrumz]

Quality. Id pay top dollar for this kind of work done at my home. Love this channel. Thanks for all the uploads.

[@rustyshakleford5230]

15 years from know you will have these videos of you working with your dad to show your kids. I wish I did something like this 15 years ago when my dad was still around. Memories are important

[@StudPack]

Yep 👍 thx Andy 👊💪

[@rustyshakleford5230]

@@StudPack Life is short.

[@tburda823]

It would be very easy for a DIY person to think "This hose clamp would be much better." Appreciate you showing what can happen if you use that type, and why the manufacturer would include a ""sub par" clamp. It's not a mistake if you learn from it, just a learning experience!