Installing Koso Heated Grips on a 3rd-Gen KLR650

  Рет қаралды 1,271

viajarMOTO

viajarMOTO

Күн бұрын

Пікірлер: 21
@deanfehr9445
@deanfehr9445 15 күн бұрын
Great video. Very informative and I appreciate your calm voice. I’m going with the Kawasaki brand heated grips but should be similar
@viajarMOTO
@viajarMOTO 14 күн бұрын
@@deanfehr9445 Thanks! Glad to help out.
@55SabreDog
@55SabreDog 3 ай бұрын
Just installed these heated grips on my 2024 KLR 650 S. Your instructions were very helpful and I got em installed with only one moment of panic! 😮 I wired them to the bullet connectors under the front headlight. I didn’t need to trim the grips by 5mm. They fit just fine as is. The panic moment was on the throttle side when the super glue set up super fast and they got stuck about halfway. Fortunately, I was able to use a rubber mallet to get them into position. Whew! They work great and I didn’t find any extra connectors laying about after replacing the cowling, etc. Yippee! Looking forward to some Pacific Northwest cool weather riding. Thanks again!
@viajarMOTO
@viajarMOTO 3 ай бұрын
Great news! Glad the video helped. As a side-note, the glue provided with my kit only worked for about a month. I felt the throttle slide a bit during a particularly hot day in the desert. I ended up using another glue that I found at a department store and that has held over the last 8 months. Enjoy the cooler weather of the autumn riding season!
@patrickcobb4483
@patrickcobb4483 2 ай бұрын
I'm digging the music
@viajarMOTO
@viajarMOTO 2 ай бұрын
@@patrickcobb4483 It relaxes me so I don’t end up throwing things during the install ;)
@justrelax129
@justrelax129 8 ай бұрын
Nice video!!!!!!!!!!!!!!
@viajarMOTO
@viajarMOTO 8 ай бұрын
Thanks Alex!
@MrShad73
@MrShad73 8 ай бұрын
Had that brand grip on my last bike and I liked them. Probably put those on my KLR in the fall. Those bolts on the bar ends are TIGHT! Nice video
@viajarMOTO
@viajarMOTO 8 ай бұрын
Nice! So far we're loving them as well. Thanks for the comment.
@retiredwaterdoctor
@retiredwaterdoctor 8 ай бұрын
great job...I also offset the positive and negative solder joints for added protection and smaller overall finish.
@viajarMOTO
@viajarMOTO 8 ай бұрын
Good call on the offset. Thanks for the comment!
@sailorman3
@sailorman3 8 ай бұрын
When taking off the old grips, get the end of an air compressor nozzle under the grip and give it a quick shot of air while pulling it off. They slide right off.
@viajarMOTO
@viajarMOTO 8 ай бұрын
Great tip! Appreciate that.
@srwven
@srwven 3 ай бұрын
Nice video, thanks. Just a note, primer does not protect from moisture unless it's an epoxy (2K). It's meant to be topcoated.
@viajarMOTO
@viajarMOTO 3 ай бұрын
Thanks for the info!
@55SabreDog
@55SabreDog 3 ай бұрын
Your videos are great and I appreciate the time and effort you devote to each one. Can I wire these grips to the connections under the front cowling? I understand that I need to install the relay first. Thanks very much!
@viajarMOTO
@viajarMOTO 3 ай бұрын
Thanks for your positive comment! Yes, absolutely you could wire heated grips to any of the three connectors (under tank, left side fairing, or right side fairing) since all are powered from the relay.
@MastaSquidge
@MastaSquidge 4 ай бұрын
Use hair spray under the grips! Slick when wet, basically glue when dry. They slide right on lol
@retiredwaterdoctor
@retiredwaterdoctor 8 ай бұрын
I would say cool video, but it's actually hot.....😁😁... Garth
@viajarMOTO
@viajarMOTO 8 ай бұрын
😂 Funny stuff. The heated grips were nice and hot for us during a recent ride around Lake Tahoe.
Installing Barkbuster Hand Guards on a 3rd-Gen KLR650
19:54
2023 Kawasaki KLR 650 Adventure Long Term Review
14:15
Therapy on Two Wheels
Рет қаралды 5 М.
She made herself an ear of corn from his marmalade candies🌽🌽🌽
00:38
Valja & Maxim Family
Рет қаралды 18 МЛН
Mom Hack for Cooking Solo with a Little One! 🍳👶
00:15
5-Minute Crafts HOUSE
Рет қаралды 23 МЛН
99.9% IMPOSSIBLE
00:24
STORROR
Рет қаралды 31 МЛН
BMW G650GS сrash bars engine guard
0:30
MottoVoron
Рет қаралды 251
Installing Heated Grips to the Suzuki Vstrom 1050DE
12:34
RichyVida
Рет қаралды 8 М.
Wiring and Installing a Garmin GPSr on a 3rd-Gen KLR650
8:52
viajarMOTO
Рет қаралды 1,3 М.
Removing Fuel Tank and Rear Panels from a 3rd-Gen KLR650
10:46
viajarMOTO
Рет қаралды 1,9 М.
Installation of KOSO heated grips on the Husqvarna Norden 901
17:18
NORDEN AMERICA - Husqvarna Norden 901
Рет қаралды 10 М.
Wiring 12-Volt Auxiliary Power on a 3rd-Gen KLR650
13:40
viajarMOTO
Рет қаралды 778
Revive your KLR 650 faded fairings
15:23
Nico Coleman
Рет қаралды 988
Honda CB500X vs Kawasaki KLR 650 (I've Owned Both)
11:05
Dork in the Road
Рет қаралды 92 М.
She made herself an ear of corn from his marmalade candies🌽🌽🌽
00:38
Valja & Maxim Family
Рет қаралды 18 МЛН