ABB Positioner Auto Calibration in English

[@vinaysane5435]

Nice Video 👍👍👍👍💐💐💐💐💐🙏🙏🙏🙏

[@antoniopintomanuel700]

Very nice; good luck for you teacher.

[@instrumentsolutions]

Thank you so much 😊

[@Meraj.786]

Gᴏᴏᴏᴅ ᴍᴏʀɴɪɴɢ sɪʀ 👍 ᴡᴏᴡ ɴɪᴄᴇ ɪɴғᴏʀᴍᴀᴛɪᴏɴ ❤️

[@instrumentsolutions]

Good Morning 🌄 Thank You

[@aminokamad1681]

Tnx brother

[@instrumentsolutions]

Welcome

[@nayrbsworld3048]

nice. our control valve is -14% at 20mA and 100% in 4mA, rotary type? can we do your procedure

[@sureshKumar-xu4sq]

Thank you

[@instrumentsolutions]

Welcome 🤗

[@sureshKumar-xu4sq]

Sooper videos

[@reyventura7623]

bro, if the control valve characteristic is equal percentage. Do i need to change in the configuration?. then calibrate?

[@robertosantossouza1020]

Hi sir from brazil !! I have some positioner TZIDC 110 ABB PA in OOS mode ( out of service ) so don't turning on (AUTO MODE) to bus comunication. We tried to reset factory and basic reset them , but still out of service continuos. You know something about its ploblem on device ? Thanks for help!

[@husseineloud]

hi iam asking about cylinder control valve is it possible to fix the same ABB positioner

[@gopikrishna.m8460]

WHILE CALIBRATNG THE VALVE AUTO 34 RUN ME STRUCK HO RAHA HI. WHAT TO DO.

[@suraiyarahoman984]

Thanks for this

[@instrumentsolutions]

Welcome 🤗😁

[@joseperadora2831]

What if valve is hunting or overshoot during stroking which parameter will need to be adjust

[@instrumentsolutions]

If the valve is hunting, there is no option to adjust from parameters. When hunting the valve, you have to adjust the volume booster. If you have any air leaks in your valve. And if there is a problem during calibration, the valve can hunt.

[@aneeshk.m5156]

Bro. I have a doubt in DP type flow txmtr FF type. In txmtr Bar graph shows inproperly. Ie, in 0% pv bar graph shows 50%, how can solve this issue.

[@instrumentsolutions]

Please send me picture [e-mail]

[@aneeshk.m5156]

I sent to your mail id, plz check

[@instrumentsolutions]

I am sincerely sorry sir for taking a little time. Actually, I did some document analysis. But last 4 years, I have not had such a problem. I think you can recalibrate again. And if not, then you can talk to a TA or Vendor.

[@moviessongs1611]

sir Field to DCS wiring kaise karte hain batao control valve FT PT LT motorised valve rotameter

[@instrumentsolutions]

Wait for my next video. Hope to see a lot more.

[@ЕсболатМурзагалиев]

hi bro, can you do this in Russian language?

[@instrumentsolutions]

Where are you from?

[@ЕсболатМурзагалиев]

I am from Kazakhstan, please tell what are you doing in this video after autocalibration, why do you set min and max position manually?

[@ЕсболатМурзагалиев]

is it not enough to do autocalibration?

[@instrumentsolutions]

See After setting the minimum and maximum range, then valve will not have any problem when it is open or closed. And if you do not set minimum maximum range, then valve may be much more open when it is open. In a word, it can be set for safety of valve.

[@rajeshpatil8729]

Bro make is Abb ok fine, but pls confirm the model

[@Farman557]

Ha bhai model Kya hai

[@mohammedsaib3844]

Neutral position is not 0 ?

[@aminokamad1681]

No subtitle brother

[@instrumentsolutions]

Sorry

[@mdakbarkhan956]

Good but

[@instrumentsolutions]

But?