Integrated Gate Hinge for huge Gates

how to weld / fabricate gate hinges that are integrated into pipe to handle long gate entrances.
Here is the link to the best welding lens I have found Here is the link for , Tefuawe WELDING LENS 👇
tefuaweweld.co...
Congratulationss on starting your new welding business. If I missed somthing, I have no doubt that I will find out in the comments. Thanks for watching guys Happy welding.
Tips for welding With 6010 ,70+ or 8010 and 7018.
Just getting out of welding school Here's some advice. I hope it helps people starting their welding journey.
#Pipewelding
#pipeliner
#7018
#6010
#RigWelder
#DownhillWelding
It’s important to go to welding school but it is more important to learn how to weld. It doesn’t matter what you do just practice and keep practicing. Nobody can hold your hand. It’s up to you. American Welding Society! Welding schools!
#WeldingSchool, #RodAngle, #TulsaWeldingSchool, #LearnHowToWeld, #7018, #6010, #taylorwelding, #weldingschools
I'm not a welding inspector, a safety man, or your mom. Do your own research. I'm not responsible for anything you do. Have an awesome, awesome day. Stay safe. welding tools homemade

[@C-Culper4874]

Chris, Looks great. The machinic in me is wondering why they weren't drilled and tapped for grease fittings.

[@TaylorWelding]

I’ve never had one seize or fail. I have put grease fittings on them before that never got used.

[@broken1965]

​@@TaylorWeldingeventually could get sweaky grease the hell out of it with high temp😊

[@berwidwhitaker2360]

Beautiful gate...great job

[@joshfazenbaker5691]

I thought the same thing. Long gate = lots of leverage on that when it starts binding, and then the pipe starts to get egg shaped. Grease at minimum.

[@wendellowens2447]

Outstanding. Quarter bubble magic trick was 👍😎

[@bjen2005]

I will have to remember that installation. I like the idea of pinning those post in like that where you can lift the entire gate off and do a repair if need be.

[@mmgtl]

I like the hing system, very slick.👍👍

[@JohnSmith-lv8xk]

Throw some grease fittings in there

[@FlyerPatty29]

My husband always preferred stick welding. He never could get comfortable with the wire feed welder‘s even though I bought him an awesome as a gift but he just couldn’t get comfortable with it. Always went back to stick welding. Shorten up the wheelbase on our trucks. He go next-door and roll the tank. I go down and get the inSan in Orange County California because septic trucks and toilet trucks have vacuum under it so they wouldn’t second one thing I worried about he was always getting down in the tank and he didn’t wear a respirator. He was 29 years older than me, but he did live to be a week for being 85 years old so even all the crazy stuff he did with his welding hand popping hazmat just saying he had a good life. And I miss him a lot. and I watch your wife with you on the pallet. No, he put me on the pallet to go paint something and I’m afraid of heights and when you get to the top, there is nothing to hold onto and then was with his homemade forklift. I love that guy and we did have a good life together. And when he got what he was having trouble, he could walk me through how to fix something tell me how to do it and I wish I could remember half the things he taught me for. What is 74 I don’t know, but I really do it.

[@LuffyFanBoy99]

Sound like you found yourself good husband and he a good wife

[@SirCarlosMusicBMI]

I Love watching true Professional’s at work ❤. When you’re good you’re good 👍. The way you think things out reminds me of my own thought process. It’s a beautiful gate. Blessings, Carlos ✝️🙏❤️😊🙏

[@Mr.Phoreskin]

Sir, this is better than any Discovery show ever! I’m addicted to this now. Glad I got plenty to binge watch. You’re a true craftsman.

[@theshieldedprepper]

I enjoy just watching these videos. I have never welded anything!...and I admire this trade skill. keep up the great work Chris!

[@Patriottoo2]

Get a machine, and get busy. Welding opens many vistas for creative people.

[@TB-LivingFree]

Quality content as usual, thanks Chris

[@godwinwelding7172]

Very nice work Boss! I’ve built several gates but I love them hinges!! Something like that will last for a very long time. Much respect bossman

[@MachoManRanchySalad]

You should do a video on your stinger. I'm looking at getting a Stubby Rod Saver and don't know anything about them.

[@TaylorWelding]

they don’t make them anymore

[@tylerworrell6731]

Really like your channel. Even after years of being a welder/fitter, I constantly crave welding information. Only just found you on KZbin a few weeks ago but I have to say you have a way with teaching. I always visit your channel to learn something new. From one welder to another, thanks man. We need more folks like you teaching the young bloods the ropes.

[@TaylorWelding]

Thank you Tyler

[@minglim-pollard1167]

What a great hinge system this is for handling cattle most particularly horses who tend to be really touchy entering and when contained within stock yard gates and holding chutes, no nasty scalping gate hinge knuckles protruding. You sir are setting the new gold standard for stockyards design courtesy of USA initiative and good old know how that hasnt been destroyed by the HR Secret police,department. Your No 1 trade assistant anticipates your every move, he is a keeper.

[@zenabu80]

That was an awesome idea. It takes a true fabricator to come up with an out of the box idea that is clean and efficient. spectacular work.

[@arosswelding]

Great job!

[@TaylorWelding]

Thanks for the visit!

[@briantruck2284]

👁️ eyeing the competition 😂 🤘 💯 Camera man game changer live action

[@harrisonwright9031]

Enjoy the videos you put up. Id recommend a tape measure clip that goes on your belt so it doesn’t mess up your pockets. I use it when i pipe fit. It’s made by holster. Seeing your weld videos really up my weld game.

[@TaylorWelding]

Great tip! thanks for the feedback. All of my pants pockets are ripped up.

[@tntltl]

Really enjoyed the video, thank you for the great content. Great looking welds what rod did you use?

[@TaylorWelding]

70+

[@jeffery19677]

11:58 #1 NO, NO! DON'T FORGET YOUR SAFETY GLASSES!!! A career welder knows that. LOL But I do like this for a gate. I retired from welding and am building my dream farm. Gates included...

[@mattm4239]

did u put grease zerks in? we have been building corrals and the zerk is a must looks great making my boys watch your stuff so they can learn before they do thanks

[@__-xq9gp]

Add an integrated fold up or retractable foot that when the gate is closed the foot drops down, locks into place and would allow 10 people to climb on the gate without damaging the gate. Thoughts?

[@nefhabud]

nice work I usually do my gates like that when it has a long cantilever.

[@hermanschijf21]

Good job,hallo from holland

[@TaylorWelding]

Cool. I would love to visit Holland.

[@CatCrazyFamily]

Another ARTIST at work. Amazing talent and ingenious way to set that all up from start to finish. Now there is MASTER talent at its best

[@TaylorWelding]

Wow, thank you!

[@davidorr1759]

Just curious, do you ever use a vibratory plate on a skip loader to drive posts in? I lived in NE Nevada, and we would get -20 degrees in the winter. Post that were concreted in tended to heave eventually, but the posts that were driven with the the plate, never budged. We also used drill pipe and would sink the posts 4 ft. deep. Really nice build on the gate and hinges!

[@TaylorWelding]

I’ve never done that. But it sounds awesome.

[@kenactofkindness4017]

16.5K subscribers Subscribed

[@OneTon677]

If Timothy Olyphant and Billy Bob Thorton had a child... it's you! With that said.. Dude, I'm a subscribed and checking out all your content.. Good info, well presented. Thanks and keep it up. Great info!

[@CameronHidalgo-kq1cj]

Hey Taylor my name is Cameron Hidalgo and I go the school at haughton high school I go the welding school at Bossier Parish Schools for Technology and Innovative Learning for welding.I know how to SMAW, FCAW, GMAW, and GTAW.I watch your videos regularly and I appreciate what you do.If you see this comment I would love to hear what you have to say I've learned alot THANK YOU

[@TaylorWelding]

Hello Cameron. That’s cool you’re learning how to weld. Thanks for the kind words. let me know if you need help with anything. I might make you a video.

[@CameronHidalgo-kq1cj]

@@TaylorWelding if I need help I will let you know

[@JackNhoff556]

That’s pretty dam slick.

[@samrobinson2119]

Looks good

[@servantofthegreatiamloving2113]

Awesome

[@americathefree3708]

Such good content! Wish I started welding earlier. Thank you sir!

[@briarpalek9254]

Nice looking project, I understand omitting the grease fittings, lazy empty headed people rarely service them with lube. They end up rusting closed and won't allow grease to pass through. Your cap will prevent water entry that could promote rust. I likely would've smeared a heap of marine grade grease on the internals of the hinge before putting it together, but I think you have a very well made lifetime gate here. As long as some drunk don't slam their vehicle into it. It may be a good idea to fasten a few reflectors along the span of the top cord just in case. Now go do this on a much larger scale along our southern border please! And don't forget to electrify it before you leave.

[@TaylorWelding]

I wish they would let me design fences and gates for the border. I would start with putting alligators in the Rio Grande.

[@briarpalek9254]

@TaylorWelding let's start an alligator farm and lease the gators out to the border states. No feed cost. They feed themselves. Environmentally friendly and self-sustaining.

[@adamabarquez8257]

Came out nice. Editing was pretty cool too

[@TaylorWelding]

Appreciate it

[@staceymain4563]

Nice job😊

[@gordjohnson70]

Why use 6010 ? 7018 works just as good and leaves a nicer bead. IMHO.

[@TaylorWelding]

it was a 70+

[@gordjohnson70]

Beautiful gate. Nice welding. Hinge style is genius. All the pipes are round, then you use a piece of square for a cross brace. Why did you do that ? I can't finger it out. My thoughts are... isn't that a mismatch ?

[@Patriottoo2]

I'm kinda surprised you didn't add support wheels to the ends, considering the swung weight.😀

[@zackbundy8097]

What a gate, she'll keep in the cattle sir very NICE

[@TalRohan]

I have just the setting for a gate like this, The last two big wooden gates I put there got ripped out by some one with a 4x4 so a nice heavy pole like that and an integrated hinge should do the trick nicely...you never know they might rip their back axle off if they try it again. Thanks for sharing

[@rascalwind]

Your partner could use an inexpensive auto helmet.

[@michaelmorris1802]

question... this is a real question... wondering about my son. Should the guy helping you be wearing arm protection? Is he close enough to get radiation from the arc?

[@michaelbaca1496]

Top shelf, no dust. Really nice/clean job right there. Also looks like you've got yourself a good hand along side you.

[@BrettNoneya]

YYEEeehhh looks like crap. Could easy have done that off just one post with the right foundation. Use the same type of hinge idea but weld the gate to the outside so when fully opened it would still be flush with the fence. Still needs 45 degree bracing on the gates as yes people will jump on them for a ride as they open so they will get bent. I can easy see 5 kids on there at once for a ride.

[@zenteno5p]

Am curios about How much donyou charge for that job Greetings fron phoenix az✌️

[@jeffstull2534]

Great job on that gate. Ingenious way to keep it strong with that pipe in a pipe method.

[@TaylorWelding]

Glad you liked it!

[@jeffstull2534]

@@TaylorWelding Dang sure did...and we replace some of our gates on the farm here I will use that method.

[@JD-526]

Nice job love the freehand notching, that's when you "know" the welder is experienced.

[@jeffrey7857]

That's a great hinge on that gate but why did you scab that square tubing in at the end It looked like you justPasted in there ran out of material or somethingI just wondering about that Just made it look funny kind of out of place

[@chrisweldz1122]

I like how the band was playing in the background are used to be on band in. This was something I like before going into this trade that was like my back up plan since I used to be passionate back in high school

[@darcam]

Theres no doubt, people, especially kids will ride those gates, time will tell if it puts and stress on it and causes dragging/binding on the Hinges.

[@tudyk21]

I'm wondering if the angled bracing will keep those long gates from sagging. Post holes seem shallow to me, too. My honest opinion.

[@robertbutler8004]

Any of these big gates without future adjustment is rubbish there are plenty of hinges that will allow adjustability where this one does not.

[@ethan....]

I think the only thing I would have done differently was to drill and tap a hole in the hinge with a zerk fittng - so that it could be greased. But that is a great design!!!

[@glenguthrie3739]

The welding was great. But the holes you drill with that little auger weren't deep nor wide enough. Lets look at in a yr and The gates will sag in the middle. I hop im wrong.

[@TORAH-613]

Do you think it would hold up had you not done the off set? And welded the gate on the roadside of the hinge post? That way the gate would've been on the outside of the post, and it would swing open to end up on the inside of the post. ???

[@BillSmith-d5e]

What I use is a holesaw drill in the middle of the pipe what ever pipe u using go one sizes bigger on holesaw you might like how I do my stainless are monel pipe

[@bernalfamily5416]

Hey, when you open the gates they seem you'll be hitting the first two parking right side and left.

[@bonkco]

awesome video! like to watch your channel while im cooking! hi from russia!

[@materialclassified]

Everyone knows that some idiot will inevitably drive into the gate and mess up all this hard work.

[@troyreif8674]

You could be a surgeon with those steady hands. I never knew a stick weld could look that good. Great job

[@ryanbeard1119]

Nice that thing isn't going to be bent easily, and since it's a real center, it's not a bracket that could get knocked around

[@ShredPile]

You could've easily made the pin and cap one piece but the extra step will allow the gate to still move if the gate barrel ever seized to the pin. Well worth it and super clean looking.

[@TaylorWelding]

Great idea

[@gamerboy-ry4hc]

How u doing man

[@broken1965]

They may need casters eventually but you use good material and practice ❤

[@waynespears5664]

Best gate Hinge Ive ever seen,WOW..........................................................................Fort Worth,Tx

[@DG-fn7qg]

Thanks for sharing you videos! Curious, what brand of torch pipe cutter did you use?

[@TaylorWelding]

Victor

[@DG-fn7qg]

@@TaylorWelding Thank you for responding! Have a GREAT day!

[@maverickweldiing8621]

if you wanna make your bottoms look like your tops mess up your tops as bad as you do your bottoms lol

[@gordjohnson70]

Did you design that gate hinge ? I never saw one like that before.

[@wadepatton2433]

Oh hell yeah, I need a couple gates. Love the 180-swing and hinge integration. I may start smaller though, one-lane traffic and all. Gotta scare up some old rusty pipes. Thanks for the ideas. I see you got the arc-shot camera setup working. Good stuff.

[@joshuagreen119]

Like the concept. Did you concrete those posts in the ground?

[@tudyk21]

1:02 yes

[@VashStarwind]

How come welding hats only cover one ear? I dont get why ha

[@danbob1650]

The video editing you got going on is upping your game brother.

[@joecliffordson]

Thanks for the demo bud. Next time you can keep the music going over the grinder. We don’t need to hear that shit. Nice gates. I may use that there idear sometime. Much appreciated

[@joecliffordson]

Well maybe a little grinder noise. Always nice to hear angry pixies skipping over the brushes.

[@deyonsadler6828]

Algorithm comment. Cause you’re channel deserves 100k

[@DIRTDUMMY1]

There's something else to the back-n-forth work on that cutting wheel... you will get more life out of them. More cuts per $$$ spent.

[@TaylorWelding]

Good point

[@LoneWolfWelding-hv7jk]

Another good one brother keep them coming your the man on welding videos

[@revelonvanarkadi5173]

This is great idea for a project that I’m working on for my gates but I’m struggling on the settings what was the settings on your welder?

[@mp13welder82]

Pretty slick doing the off set to open onto themselves

[@samuelscragg7052]

Good tip on the cut off wheel thanks

[@m4droid]

I was wondering who built those. They look good.

[@TaylorWelding]

Thank you

[@1963SMITTY]

Did you string line across the opening to get them the exact same height?

[@TaylorWelding]

I used laser

[@1963SMITTY]

I forget about those!

[@brandonl5343]

Very slick, a true professional in his craft!

[@mider9996]

Do you need a lot of math to do that or just common sense

[@gordjohnson70]

Nice job, but No gussets ? I luv gussets ! LOL

[@myfoundrylife]

Very nice. The hinge is awesome.

[@lukewarm2075]

That Hinge is the best hinge i have aeen made.

[@paulusmarc]

Bon Boulo 😆😆👍👍

[@alexgrubb6640]

Good teacher

[@jameschupp2230]

Awesome ! Would it be beneficial to put some grease zerks in?

[@TaylorWelding]

I don’t think so. I’ve never had onefail or seize

[@jameschupp2230]

@@TaylorWelding ok, Cool... I wanted to build a 24 foot swing gate, but everybody says not to do it. But that type of hinge would be the best style for something like that.

[@TaylorWelding]

@@jameschupp2230 that gate was over 19 foot.

[@jameschupp2230]

@@TaylorWeldingOk, So 24 ft is possible. Oh and I like the Swing Back as well.

[@robchesley4591]

Beautiful job. Well thought out

[@paulg5900]

Curious his process for setting the posts in the ground with concrete.

[@JM-wc2kv]

Looks great to me and pretty good ideal. Its nice to watch in learn other trades. I did welding in high school and liked it, i just bought me a stick welder and would like to get into business how you are. Im on my way but still need to learn more. Like i said i like learning all trades i do hvac and handy man stuff. Im good with my hands. Anyways mice work keep the videos coming

[@TaylorWelding]

Cool, thanks!

[@lodown830]

Thats badass. One big o hinge.

[@georgesimpson3113]

Why don't you weld up hill?

[@elhuanimaro]

Nice work man 👍🏼👍🏼👍🏼👍🏼👍🏼

[@randycordes464]

That some good welding

[@יובלשגב-ח5ו]

seeing your work process and thinking is fantastic

[@TaylorWelding]

Thank you so much 😀

[@alvinwhitlock4306]

Awesome job

[@comingtofull-ageinchrist6736]

Genius design for the hinges!

[@TaylorWelding]

Glad you like them!

[@kenactofkindness4017]

oil or grease the hinges or not lol, fantastic education take care hi 5

[@kenactofkindness4017]

@TaylorWelding 1 hour ago I’ve never had one seize or fail. I have put grease fittings on them before that never got used. 2 Reply

[@kenactofkindness4017]

anti rust my goal minnesota salt belt lol

[@kenactofkindness4017]

rust the new lube hahha works anyway yahooaloya