Introduction of MaxiTPMS TS508

Check out www.MaxiTPMS.com for all your TPMS needs. This video is directly from the Autel MaxiTPMS website.
If you have any questions in regards the the Autel line of TPMS tool I am happy to help.
All credit for videos goes to Autel and Autel MaxiTPMS.com
www.maxitpms.com/tpmscms/Video...
MaxiSys Tool Videos:
Autel MaxiSys Shop Manager: • Autel MaxiSys Shop Man...
Autel MaxiSys Pre and Post Scan Report: • Autel MaxiSys Pre and ...
Cobalt BCM programming: • Cobalt BCM Coding
Autel MaxiSys Registration and update: • Autel MaxiSys Registra...
Autel MaxiSys Updates and How to Redeem: • Autel Maxisys Updates ...
MaxiSys Line of Tools Explanation: • MaxiSys Line of Tools ...
MaxiSys won't update: • MaxiSys won't update
Autel MaxiSys Battery Care: • Autel MaxiSys Battery ...
Autel TPMS Videos:
TPMS Relearn Function TS508: • TPMS Relearn Function ...
MX Sensor Programming TS508: • MX Sensor Programming ...
Introduction of MaxiTPMS TS508: • Introduction of MaxiTP...
Causes and Resolution for TPMS MIL: • Causes and Resolution ...
Autel TS401, how to program MX sensors: • Autel TS401, how to pr...
How to update your Autel Autolink and TS401 tools: • How to update your Aut...
How to update Autel Autolink and MaxiTPMS with SD card: • How to update Autel Au...

[@gobofraggel7383]

I am at Toyota with my 2015 Highlander for a blinking tire pressure light even though tires have proper pressure. Diagnostic charge for this is $300 which they say is waived when you pay for the repair.

[@MrtalentedReid]

Interesting I just received one from Amazon

[@MrtalentedReid]

Interesting

[@rodolfopacheco1521]

Houston, Tx tire and wheel dealer here. Been using this programmer which works well with autel but iffy on others from time to time. You CANNOT program sensors unless its an Autel 315/433 mx sensor

[@Mau105]

thank you for verifying what i have learned the hard way, NAPA feigns ignorance, I fully believe they know exactly that this is the case

[@DAVIDRAUL79]

Good evening, I have a query, thank you for your support, I bought a MaxiTPMS TS508 and bought four new sensors (two pairs of different brand and model), but I could not program them, the scanner did not recognize any new sensor, instead the sensors that my hyundai Elentra Turing 2010 has, the rear sensors did not work and now I can't take the TPMS light off it. Something similar happened to you How could I contact you for a question or someone from your audience that something similar has happened to him. Thanks in advance

[@FlashPerformance]

Autel has a tech support line that you can contact in your region. Go to Autel.com>support. My guess is the sensors you purchased are blank and are not compatible with the TS508. I recommend the Autel MX Sensor, VDO, John-Dow, Ori-Tech, or OE sensors.

[@StilettoSniper]

Did you purchase Autel MX sensors? Because if you did not, that would explain why you cannot program them with a MaxiTPMS tool.

[@SchecterMongoose]

Do you need to reprogram the sensors after a tire rotation?

[@FlashPerformance]

That depends on the vehicle. If you have a display on the dash that shows the tire position and the tire pressure, then you would need to relearn the positions after each rotation.

[@ubugarrity]

Does this read and work with all OEM sensors or do the sensors have to be MX?

[@FlashPerformance]

Yes, the Autel tools will read any OE sensor, information ready sensor, or pre-programmed sensor. It will also clone and program the Autel MX sensors. This video has information about the different type of sensors. kzbin.info/www/bejne/rKiwqXuubbyij9k

[@FlashPerformance]

@Boy George amzn.to/36O7i3O

[@donaldindividual-1]

@Boy George 300$

[@haydent3566]

Can I program the OBD on a 2013 Toyota Tacoma. With the TS508?

[@FlashPerformance]

Yes

[@knight3131]

Can you activate OEM sensors ? And update the ECM with the new sesnor ? Or you can only do this wil Autel's sensors ?

[@FlashPerformance]

Yes, OEM sensors are covered

[@nothingtoseehere5760]

How can I program the sensors if they are already installed in the wheel?? Why is this not covered by any content it's so frustrating!

[@FlashPerformance]

sensors need to be programed outside of the wheel or with no pressure in the tire. If the sensor is already installed in the tire, deflate the tire and try to program with zero pressure.

[@radioace318la]

so in short, this is a proprietary programming tool just for YOUR sensors?

[@Mau105]

I have been wrestling with this exact issue, and it does appear that one needs an Autel programming tool to turn on an Autel sensor sold by NAPA, NO ONE locally has the tool!!

[@chadwilliams3380]

If you don't have old sensors can you use this to program new tpms sensors to vehicle?

[@FlashPerformance]

Yes, I recommend using the Autel MX Sensor, those are the easiest to use in replacement. You can also use VDO or OE sensors and the TS508 will do the relearn

[@StilettoSniper]

ONLY if they are Autel MX sensors.

[@conchim99]

@@StilettoSniper can this tool program cheap toyota eBay tpms sensor?

[@torredecontrol7079]

Can I become a banded tpms into a normal tpms with this machine ?

[@FlashPerformance]

Yes, take the band off, clone the TPMS sensor, install into valve stem location and ship it.

[@jamiefenner123]

Can you use code brand new OEM sensors from the dealership or do they have to be autel sensors?

[@FlashPerformance]

You can do relearns on any information ready sensor. That includes: OE Dealer, VDO, John Dow, Ori Tec, Dorman, OR Match and more

[@4xAbuse]

Relearn vs Unlock is important to differentiate. I just got a TS508 yesterday to 'activate' a VDO Redi-Sensor SE10003A that I installed in a wheel for a 2005 Cadillac Escalade ESV. Come to find out now that the new VDO sensor is installed, that my TS508 doesn't see it. VDO tech support says that while it's 'Redi' like OEM, it has to be 'Unlocked' first and that requires a more high-end specialty tool, such as a Bartec, Ateq, Snap-On, etc... VDO tech support also says that they 'may' work out of the box and be recognized by this tool, but not if they're installed and driven on first. But it's still a crap shoot at best, according to them if you'll need a better scan tool or not, even if you don't install and drive on it first.

[@StilettoSniper]

@@4xAbuse After you purchased the Redi-Sensor, who did the initial programming on it? Because you can't with any Autel TPMS tool. Autel TPMS tools can only program Autel MX sensors out of the box. VDO tech support should have told you this immediately instead of feeding you a crock of bullshit about unlocking their sensors.

[@4xAbuse]

@@StilettoSniper It's been a couple of years now, so it's hard to remember the details exactly. No one did an initial programming on it though. It was marketed as being 'Redi', so no special tools, etc. Seemed like I'd used one previously that was just like that. I installed and it just worked. I went to a couple of local shops to see if they could 'wake it up' or if they had one of the recommended tools and no one seemed to have seen that issue... I've since run into an interesting situation on a Dorman for an '08 Jeep Grand Cherokee. It would transmit the pressure, but wouldn't communicate with the location sensor in any of the vehicle's 3 wheel wells. They sent me a new one and it was the same. Would work fine in the driver's side rear (no location sensor in the wheel well), but would trigger a location error if moved to any of the other 3 positions. Finally just replaced it with an OEM and it has worked fine since. Dorman couldn't understand why the part they recommended for that application wouldn't work, so they sent me the OEM one in exchange.

[@peterhirsch8044]

Can I install new mx sensors and activate them later? Like drive two days and then activate them?

[@FlashPerformance]

Yes, You can program the sensors while inside the tire. They should be able to be programmed no problem. If you have issues you may need to deflate the tires and then program them.

[@nothingtoseehere5760]

@@FlashPerformance No no no, NOBODY has provided ANY instructions on how to activate new sensors that are ALREADY INSTALLED in the tires. PLEASE provide a step-by-step for the activation (not pulling the codes for the old ones but ACTIVATING the new ones with the codes).

[@FlashPerformance]

@@nothingtoseehere5760 kzbin.info/www/bejne/baPWq4aigLCtl8k

[@FlashPerformance]

@@nothingtoseehere5760 kzbin.info/www/bejne/qWXJiKyHqb2Aq9k

[@webgazda]

Can i activate BMW Motorcycle sensors with this unit?

[@FlashPerformance]

Yes, and honda goldwing

[@youngmalcolm8603]

can u program aftermarket rims and tires with this?

[@FlashPerformance]

The aftermarket rims and tires are not the factor in TPMS programming it is the sensor in the wheel. You can not change tire size that I know of

[@SuperNica68]

Hi, install new sensors to my 2013 Tacoma Autel TPMS MX-Sensor 315MHz 433MHz. I have a MAXITPMS 508 scanner, I reprogrammed them, I installed them by obd, the installation was successful, the message but. When I am in the parking lot where I live, the light turns on as if a sensor were bad or a tire and when I go out of the building to the street outside the parking lot where I live. The light goes out . that always happens to me. the air pressure was fine. The Sensors tells the scanner that all 5 are fine. I did the reprogramming of the sensors more than once and that always happens to me. only where I live in the building park. because the light turns on the screen only in the parking lot of the building. I wait for an answer. They are in the correct position.

[@FlashPerformance]

On the Drivers door there is a placard sticker that shows what each tire should be inflated to, make sure that your tire pressure matches that sticker. Second would be checking the accessories you have in the vehicle. I have seen aftermarket back up cameras, and other wireless accessories mess up the signal from the sensors causing interference and a light to come on.

[@enriqueleon2127]

En la ciudad dequeretaro o en la Ciudad de México quien tiene este escaner para que me informen si algún sensor de mi town and country está dañado , gracias

[@fretted]

2017 Honda Pilot Touring support?

[@FlashPerformance]

2017 is still pretty new. The relearn procedure is not in the tools as of yet. However you can still replace the sensors by using copy by activation. Here is the info from the Autel website www.maxitpms.com Relearn Procedure: 1. Relearn method is not yet supported. Only Copy is available. 2. You can use one of the following three methods to copy according to the actual situation ? Firstly, copy by activation. Secondly, copy by OBD read IDs. Thirdly, copy by manual input the OEM sensor IDs (You need to notice the data format is decimal or hexadecimal). This can be done with the TS508, TS608, MS906TS, and copy by activation can be done with the TS408

[@stevealaska73]

I have a 17 Pilot Touring too. How are you liking yours thus far?

[@chramg]

@@FlashPerformance but, you got to use autel mx sensor or you can get another aftermarket tpms ?

[@FlashPerformance]

@@chramg Autel MX Sensors, OE sensors, Information ready sensors, and any sensor that is already programmed. This video might help clear up the different type of sensors. kzbin.info/www/bejne/rKiwqXuubbyij9k

[@khangnguyen-vg4tz]

hi there can i programs 2008 lexus es350

[@FlashPerformance]

www.maxitpms.com/getCoverage.jspx Yes, it is an OBD2 relearn. TS508 would handel that no problem

[@elmecanico4943]

How much? Can I have one for my birthday??😁

[@harvaulakh3033]

Does it work for Schader ez sensors?

[@FlashPerformance]

The Autel Tools can not program EZ sensors. The EZ sensors must be programmed with an approved tool, then the Autel tool can relearn it to the vehicle

[@harvaulakh3033]

@@FlashPerformance thank you for the reply. When I got my ez sensors installed first time, 1 years ago, they were programmed. Now car stopped reading them after winter tire swaps. Does it mean normally that car needs just relearning only which can be done with this ts508 device? Or I have to program and relearn every time after tire swap?

[@autoshaman4319]

having a terrible time figuring out how to use my Autel ts508 Nothing easy about it . Tech line people clearly dont have the patience to walk me through it and step by step instructions are great until you run into a problem then there is no info on further diagnostics . Anyone ?

[@FlashPerformance]

Autel has a lot of good how to videos on the channel kzbin.info/aero/PL9YQaAMZT0m1-h3Q-9uJDjEf2XyaJibKg these may help answer some of the questiong or issues you are having.

[@militarygradegear4004]

Comment #50!!

[@teckluv4413]

This precess can be done with any repair tire shop but, It doesn't . Only big company like pepboys, firestone can work and program tire sensor. This is a shame! because the cost of the part and instaltion is $116 / tire. I run to walmart and dealers but the programmer tools did not work on my 2019 Mitsubishi mirage.

[@StilettoSniper]

Any automotive repair shop worth a shit that employs competent mechanics can handle replacing, programming and relearning TPMS nowadays, as long as they have a TPMS tool that is compatible with the sensors in question. Places like PepBoys and chain stores like Firestone and Walmart usually hire the bottom of the barrel grease monkeys, I would not let them get near my vehicles.

[@richyzenteno1349]

I purchased OEM sensors from dealer and i already installed them on my 2007 toyota tacoma.. can i use this Ts508 to activate and remove the tpms light on dashboard?

[@FlashPerformance1]

Yes, you just need to do the relearn process. Select the Year Make and Model of the vehicle and press the ? button. This will give you the relearn procedure directly from the tool.

[@StilettoSniper]

Who programmed your OE sensors from the dealer? Because you CANNOT program blank Toyota OE sensors with an Autel TPMS tool.

[@brexit9279]

This equipment would not program my sensors. This was confirmed by the factory technicians!

[@makaynchealhalibbealkhooo9673]

The snop on is way better and is like 200$ more

[@ourahoumed7126]

BONJOUR EST CE QUE CE PRODUIT NECESSITE UN ABONNEMENT OU SANS ABONNEMENT

[@makaynchealhalibbealkhooo9673]

ourahou med avec abonnement

[@MonzaRacer]

dude you way off base, so fare ai have cloned new MB, BMW, Ford,GM Hyundai. So far never had an issue AND the dual band sensors with quick disconnect are awesome so you can swap sensor between either rubber or metal stems, swap in new sensor in seconds and it reads everything so far including a universal set up for a motorcycle and trailer tpms kit. And you can get kit with 8 sensors with rubber stems, 4 extra metal stems and such and all for around $350! I like snap on and own boxes scanners and lab scopes. But this Autel product lives up to every thing they claim and more.

[@TyRC12]

@@MonzaRacer Do you know how to program a mx sensor when 2 sensor IDs are the same? The other 2 are different. It wont work when i program from copy by obd when 2 ids are the same

[@martinS-vn3wy]

It's a shame it only programs/clones Autel sensors, might have been tempted if it programmed all leading makes.

[@FlashPerformance]

The Autel tools will program any informaiton ready sensor, that includes: VDO, John Dow, Ori-Tek, Continental, OE Match, and all OE sensors. You will able to relearn an pre programmed sensor. Check out this video: kzbin.info/www/bejne/rKiwqXuubbyij9k

[@StilettoSniper]

@@FlashPerformance No, what you are saying here is incorrect. Autel TPMS tools absolutely WILL NOT program any information ready sensor, such as: VDO, John Dow, Ori-Tek, Continental, OE Match, and all OE sensors. Autel TPMS tools can ONLY program Autel MX sensors. Please make sure you understand the difference between PROGRAMMING and LEARNING and use these terms in the correct context.

[@radioace318la]

Good information to have. Thank you sir. This whole TPMS government SCAM has been a major PIMA. I bought 4 new "Findauto" sensors for my 2015 chevy. Had them installed just to learn this tool WILL NOT program them with my car. It's all very proprietary with NO standard. yeah, everyone and their brother sells a relearn tool but many times the uninformed will spend a lot of money on useless crap that doesn't play nicely with others. Cheers from Louisiana.

[@user-uy5tj6eq7c]

Ничего непонял

[@juanportillo2201]

Comment #51

[@williamai7808]

hello, we'are seller of Deewaz TPMS, would like to invite you review for our free devices. Let me know your idea

[@FlashPerformance]

What options do you have for a Dually or RV and Trailer?

[@ss-rw4kr]

Je veut change langue de moi autel en français

[@FlashPerformance]

Contact your local Autel Support team, they will have to add French to the download server to add the language. Or you can email [e-mail] and request it with your serial number

[@ss-rw4kr]

@@FlashPerformance aidé moi changement de langue svp

[@e9hama516]

ok