Introduction to Two-Port Networks

[@ALLABOUTELECTRONICS]

The timestamps for the different topics covered in the video: 0:20 What is Port? What is Two-Port Network? 1:12 One-Port, Two-Port, and Multi-Port Network 2:10 Importance of Two-Port Network Model

[@factsbygirl]

🤩🤩who else watching it after years. 🤩🤩

[@rahuljangir7100]

please cover all ece topics........... you are better then our mnit teachers

[@bipulkumar6637]

even IIIT allahabad

[@qasdheem8289]

A simple,clear explanation Thank you sir

[@Shafiqaakhter-y4i]

Nice video sir. You teach very well & write it in the description too. Hats off 🎓

[@lohitaraya2401]

thanks a lot for the video sir .it is very helpful for last minute preparation

[@gee5884]

Thank you sir. It was very helpful. Easily understood

[@MSdrumsGospadu123]

Thank you sir your video varey help full for meee and your teaching varey well sir

[@aliabdelhadi1104]

Many thanks.. Your vids are so clear I have a question for you.. Can we apply nodal voltage analysis to a two port network problem? .. is it possible to assume v1 (voltage of input port ) as a voltage source in order to use in nodal analysis equation?..

[@صوفیانہموسیقی]

sir if we r applying voltage or current from both sides of network then from where we get output...???

[@dedeepyasepuri7042]

thanks . your videos are easy to understand

[@laldintluangachhangte3061]

I love all your contents, keep it up

[@poojashah6183]

Just Superb 👌🏻👌🏻

[@mayurshah9131]

Excellent 👍

[@engineerkohat]

Wonderful video.

[@alvaroruiz6254]

Nice explanation!

[@prathikkamath5642]

Very well explained

[@jankampetsampath503]

Do more on network analysis

[@engineervimal]

Thanks u all ke liye♥️♥️

[@shwetahegde8850]

Very helpful

[@mnada72]

3:23 what are the 2 ports of the transistor ? for example is it b,e one port and c,e the second ?

[@ALLABOUTELECTRONICS]

It depends on which configuration the BJT is used. When it is used in the CE configuration, then input is applied between base and the emitter and output is measured between collector and emitter. So, in such case, base and emitter terminal will be the input port while the collector and emitter will be the output port.

[@mnada72]

@@ALLABOUTELECTRONICS but how does the port rule is applied here ? The current input to the port equals the current output from the port

[@geethag3420]

@@mnada72 Same doubt...

[@justpaulo]

Why are we switching to 2-port Networks when we were seeing stuff about BJTs?

[@ALLABOUTELECTRONICS]

As I mentioned in the one of the community post, it will be required to understand the small signal model of the BJT. (h parameters). Once it will get finished, the small signal model of the BJT will be covered.

[@solomonbirhane3648]

nice explanation sir. please upload series videos on network analysis.

[@ALLABOUTELECTRONICS]

Please check this playlist. Here is the link: kzbin.info/www/bejne/sIaqkohqoL-jl8k More videos will be added to this playlist.

[@researchtalks6000]

Nice video sir !

[@nikhilbhukya7894]

can you please share the slides????

[@gurusamyd9531]

Sir what is linear circuit

[@ALLABOUTELECTRONICS]

Just go through this video. I have explained in it. kzbin.info/www/bejne/an3KhH-KpLGGebc In case, if you still have any doubt, let me know here.

[@MukeshKumar-ku4ey]

Sir pura two port kab tak finish karoge

[@ALLABOUTELECTRONICS]

Will try to finish as soon as possible.

[@davekuzara2783]

3rd

[@OCEAN-fc9wl]

headphones users beware..

[@tusharsangat1180]

Hey ,Are You On Instagram I have a Doubt.

[@sistemsylar]

accent accent accent