IR-Sensor USING LM358

[@yubraj4772]

Your explanation is too good than other youtubers.

[@shrikantnikam2426]

How long it can sense.

[@creationmode9889]

Ye photodiode kya remote ma mil jaya ga?

[@rahmanocawni5618]

Hi friend. Détection distance please.

[@nitinpatel5447]

Kya hmm. Is Circuit se Ghr ke light ko on Ya off kar sakte hai.

[@deepakkumarsingh1589]

Fabulous sir

[@creativethinker6064]

Love This..!! 🥰 i’m always watching you..: 😊 keep it up 💖'

[@ushnajaved4911]

Line follower kahan hai apka?

[@lukegrossotron8015]

Distance???

[@incxxxx]

Im not a beginner but I do not understand. You have made receiver or transmitter or both ??? Do you intend to use it as a receiver or transmitter depending on the need?

[@hobbytechnical1097]

Thanks for giving knowledge

[@rjvashist9329]

good one bro

[@fdiy8612]

superbly explained Sir, good job! I had an IR module , I attached a 5 vmotor pump to it using a TIP32C transistor, Output from module is attached to base of transistor, VCC 5v from power source & module to the Emitter & positive line from pump to collector, when the current is switched on it makes the pump to run continously , It , however slows down when an obstacle is brought near the IR transmitter / Photodiode, is there something wrong with the IR module? I was trying to make an automatic soap dispenser

[@fdiy8612]

I found the solution to the problem, I realized there are two types of IR module in the market , one with single LED which works well with BC 457 transistor , as shown in your schematics & other with Two indicator LEDS, which works well with TIP32C /TIP 42c

[@mraj9914]

Nic one bro

[@maheshnallamothu2624]

can we use this to count heart beat

[@manojkiyan4033]

What is the difference between output and ground??

[@MakeloGy]

Ground -ve supply Output sensors signal for device

[@manojkiyan4033]

@@MakeloGy so what should I connect at output in the circuit??

[@chandrashekharmirajkar2611]

Manoj Kiyan , you can drive bigger load with transistor and relay connection

[@MakeloGy]

In this pin sensor provide you output so that you can use anywhere .. like feedback of This sensor . Using this signal you can find distance, line follower ...

[@manojkiyan4033]

@@MakeloGy but the IR reciver have only two legs(+ & -)

[@niladritheboss]

can i use ir reciver 1738...if yes then why... if no then why...

[@ivanromaniuk9834]

It should be partition between diodes.

[@sadabraza4841]

Lm358N/Lm358p???

[@big_o1952]

What is the difference

[@anishshahi5070]

Nice technic...bro

[@MakeloGy]

Thanks bro

[@morvi.argon.welding.machin4066]

Surya ke Prakash ko accept na Karen Aisa koi upay bataen

[@MakeloGy]

Gher me chalao 😁

[@MakeloGy]

Try this one forum.arduino.cc/index.php?topic=134089.0

[@SumitSingh-kk3sq]

Aapne starting me blue led ko photodiode bataya lekin bad me usko IR Receiver bata kar connect kara kya sahi hai shayed tabhi ye kam nahi kar raha don't make fake video plz

[@mukeshprajapati4518]

Bhai sabji Muje viring patanahi kese karane gi

[@cooldude2074]

Bro here one thing is wrong that is it led's negative will be connected with resistor and then to ground

[@aquarismohobbydiversos.fre894]

Show it working.

[@mdalamin4724]

Main problem is you can't use it at sunlight

[@animeshgarai201]

3 leg ki ir reciver ka fitting bataya. 2 leg reciver no avelable. TSOP1738 AVAILABLE

[@sonushukla2873]

Sir 24 vdc main banao

[@furqanali9967]

Maine ye banaya ha lekn ye sunlight Mai direct Kam KR RHA ha or night Mai sahi Kam KR RHA ha Maine is ko shade bhi provide kra ha phr bhi Kam nhi KR RHA.

[@uniquetechchip]

Plz make levitation anti gravity

[@anandjoseph8405]

Add it's working

[@rogercaballeda7042]

You did not test ur work!!!!

[@MohammedRiad]

Why didn't you test it. I used the same schematic but didn't work waste of time

[@rudrashiva]

Why you are wasting opamp when you can use NPN transistor. It will create your project cheaper.

[@luckyartwork2194]

Keya ye kaam nehi kar raha... Ek baar jaala k dikhana chahiye tha... Tum par se to mera varosa uth geya...

[@satyendersingh9616]

Speak slowly brother

[@MakeloGy]

Ok i will remember this thanks