ISOPON Body Repair Kit For Holes

ISOPON Body Repair Kit for Holes easily repairs rust holes up to 3” wide so it’s ready for painting. The kit contains all you need to make a perfect repair, including convenient, pre-measured packets that are easy to use for mixing, primer aerosol, spreaders, personal protective equipment, and more. Fibreglass reinforced formula is tough, durable and easy to sand.
ISOPON is a new range of automotive body repair solutions offering ultimate ease and convenience for DIY car enthusiasts. Conveniently packaged kits come with everything you need for a quick and easy DIY repair.
www.isopon.com

[@cancan8467]

I repaired spoiler boot holes with it And worked amazing it’s strong stuff

[@souravbhattacharyya3392]

Product is off course effective,but more than that I salute your hard work, patience and final touch.

[@marksmith5237]

One of the lads drilled a hole 25mm wide in a galvanized steel water tank, filled it with isopon, still holding up today, brilliant stuff. has been under water for 12 years now, not sure if the good people at Isopon recommend it, but it worked for me.

[@TunedVXR]

Dislikes, why ❓😓 there's always someone who thinks they can do it better lol,great video I'm going to be buying this kit for my bumper 👍

[@minikmetija1905]

It's not abaut the kit itself it's abaut that if you cut metal away you HAVE to put in a new metal part not just a pice of "foil" and body filer the paint will start bubeling and the metal WILL start to rust

[@spinach4949]

@@minikmetija1905 what metal will rust? And wait for the filler to harden properly before you paint it?

[@minikmetija1905]

I am a body worker and when it starts to rust it dosen't matter that you sanded it away the rust is already in the metal that is why you need to cut araund the rusted part to cot away any rust whitin the metal itself. That is my experiance as a car body worker. I am doing it for some time and speaking from experiance. Plese do not think i am talking shit abaut your video

[@spinach4949]

@@minikmetija1905 I understand what you mean now. They did cut away all the rusted metal in the video. You say you should put solid metal in the hole rather than mesh but I don't think the filler would hold as well onto a flat surface than it would to a mesh and the filler should be hard enough not to need it?

[@minikmetija1905]

@@spinach4949 as i alredy told you i am a car schooled car body and paint worker and if you sanded the metal patch whit 60-80 grid sand paper it will be on ther for as long as the metal dosen't rust again. But i understand the perspective of a DIY man and the differance is deffenetly the price and the end result, plus to do a proper repair you need a welder and considering the price i understend your way of repair. Please understend that all i am doing is explaining the proper method i was thot and taking intho consideration i restored multiple vintage cars i can say i have some experience. If you want to learn more abaut car body repair go to the eastwood company youtube chanel

[@Tracks777]

Awesome video,Keep it up!

[@nulisnulelis8031]

This is very good kit every thing is included what will you need to do the job well done ISOPON™

[@reza_dc2]

What if you don't have access to the backside of the hole? Thanks

[@KenpoOjoko]

I wonder if only applying the material from the front side create a strong enough foundation. Should you also need to apply it on the back side so that the mesh gets strongly fixed onto the body? I feel a strong pressure on the repaired area could give in.

[@tj-kf7bk]

I subscribed off this video good work guys

[@melkelly9371]

My 01 ZETEC s fiesta failed NCT/MOT on rot in the wheel well and structure used this fairly badly but Sand and sprayed it well, hard as a brick wall, flew through its last two tests

[@spicelife6338]

Well that's dangerous 😬

[@MrRockydee07]

Great video, I have 13 antenna holes in my ex police car that need paching will this work for this .THANKS

[@enrico0094]

This is helpful, thanks, but differs from the instructions on the Isopon aluminium mesh (sold as a separate item). That recommends using a small amount of Isopon P40 (hole filler) to stick the mesh to the rear surface of the metal, let it set, then fill from behind the repair with more P40. Finally, when that has set, add a layer of Isopon P38 (looks like the second lot of stuff that the person in this video mixes up), allow it to harden, then sand down. So I'm confused! P40 is VERY difficult to sand down because of the glass fibres in the mixture which become brittle glass whiskers when set.

[@quraishalgurabi8089]

👍👌Thank u for the vd.

[@keeponkeepkeepingon8376]

*U POL I have a question: For example when a vehicle/car has been rear ended by a tractor trailer truck (hitting one side of the rear bumper) cracking the bumper / ripping off one of the tail lights aka brake lights and smashing the rear quarter panel...... QUESTION ONE (1) What are other possible issues that are likely to have occurred to the vehicle that the naked eye and non mechanics/non body shop specialists would not be aware of* *could yah list the guestimate price for each repair including the obvious repair/replacement of the bumper, tail light and rear quarter panel*

[@roadwarrior7401]

how does the tape holding mesh not fall off ? especially after getting wet with road use ? which seems to be the only thing holding mesh on the rear

[@christianmccombs1913]

I want to take off my cars spoiler, would this work good?

[@RamelleKnight1]

Can you use this for a hood?

[@stevebevan5104]

Of course! Line B before Line A

[@coletrain72]

Can this be used to repair holes in the roof of a car? Is it waterproof?

[@np2631]

Can I use this product on the roof of my car, there's a little hole 🕳

[@chrispy7785]

Can you apply the mesh on the front side of the panel if don’t have access to the back ? Than fill and sand back ? Thanks

[@leedh123]

I have the same issue. The back of where the hole/rust is cannot be accessed to attach the mesh. The job itself looks straight forward, I'm just at a loss as to how to create a backing to apply the fibreglass....

[@rowbes]

Would this still work if the hole im patching is a sharp curve on a front bumper?

[@UPOLRaptor]

Hi Juza, A repair to a sharp curve should be possible, it will just be more tricky to shape and apply the P40 filler to the aluminium mesh. Shaping the repair whilst sanding will probably also be more time consuming than a flat repair.

[@Evan-rb5ep]

Good video, but Are you not supposed to shake the can of primer in a swivel motion instead of , a up and down motion.

[@UPOLRaptor]

Hi Evan, The aerosol provided in this kit will contain a small metal ball, this will potentially have settled at the bottom of the can along with some of the base product - shaking the can in an up and down motion will release this ball and ensure that complete mixing of the base with the propellant to give the required product application.

[@Shanedog76]

why do you squeeze out the harder onto the mixing sheet in different amounts? first the A amount, then the B amount???

[@bunnydavies8783]

Types of fillers vary in their chemical composition and therefore need different amounts of hardener to ensure they cure (set) correctly.

[@vanessalang4843]

My car got caught on a metal post and one of my doors got left with the metal literally being cut and there’s a hole. Gonna try this, the results look insane

[@BobSmith-mc7uq]

Girls & driving do not mix! Sell the car, take the bus.

[@Shanedog76]

its my car ''has'' a metal post not my car got on a metal post??? who taught you grammar white trash?

[@teeteegmail1298]

How did it work? I have the same problem and the mechanics just want to replace the whole door 😢

[@DenBank1]

So what’s the result of your experiment with Isopon. I got the same problem and the garage says £12 thou to repair properly Thanks

[@DenBank1]

So what’s the result. Did you try it?

[@808timmyturner]

Where can I buy this kit?

[@ieuanmale-maltby5869]

Hi, hope you can help! What if I'm making a repair where I can't get to the back side if the large hole? how do I secure the mesh?

[@dunebasher1971]

The mesh HAS to go behind the hole, so you have to get behind the panel somehow. If you can't do that, your only option is to forget about body filler entirely and repair the hole by welding in a new piece of steel (which some will argue is the only proper body repair anyway).

[@katarzynazurawska9787]

we have a plastic bumper? will it work on the plastic?

[@UPOLRaptor]

Hi Katarzyna, No this isn't suitable for plastic unfortunately, we have Isopon Plastic Filler for use on plastic substrates. Hope it helps

[@elias2024]

I can't find this product in the market

[@TrentStrong]

What if you dont have access to the backside to apply the film? Can you do it to the front?

[@pooorman-diy1104]

that's a valid question..

[@UPOLRaptor]

Hi Trent, Repairing a hole from the front can be done. You will need to tap the edges of the hole to create a slight recess for the mesh to sit in - this will then allow the mesh to sit level with the metal substrate. Hope it helps

[@Kahnklingon84]

Is the mesh magnetic? Could you use that to help pull it towards the body

[@johnwalkley6746]

@@UPOLRaptor how is the mesh fixed in place?

[@gwenhwyfer9033]

How can i place the screen when i cant reach into the rusted hole? It's like a hollow space and i cant enter the place any other way then via the rusted hole

[@TheDutyPaid]

Thread a thin piece of wire through a number of the holes in the mesh, put the mesh into the hole and pull from the outside. Then follow the rest of the video.

[@gwenhwyfer9033]

@@TheDutyPaid thank you! Will try that!

[@taab7]

So the repair is permanently held in place by strips of gaffer tap??????????

[@dustinho227]

How much is it?

[@pipikakachu]

Then the filler can be painted so that the color matches the car’s ?

[@UPOLRaptor]

Yes, you will need to use the primer provided. Allow it to dry, sand to a perfect finish and then apply the color of your choice.

[@pipikakachu]

U-POL thank you, I will buy a kit.

[@Sterayb]

A lot of the time you can't get to the back of the hole then you have to be inventive

[@stevenm3141]

This seems odd, aluminum against steel? Doesn't this cause electrolysis? There by inherent problem in the future.

[@jdogghizzy2606]

So you just leave the tape on the back?

[@victormedina177]

Yes, because the tape is the only thing holding all of these together lol

[@theeaskey]

Will it work on aluminum

[@SamFBM]

ofc

[@camr.c.p3937]

but how am i supposed to put the wire in the fender if its on the car dude

[@animationcrate]

Big homie Dax Pull off the fender

[@camr.c.p3937]

BlueKj doesn't come off its part of the back of the car

[@Shanedog76]

the car is what your fixing isn't it??? duuuuueee

[@tallllkiddddddd]

2:29 Can i place that mesh on the front side if i cant reach the back?? any suggestions?

[@Star-Performance_]

Of course not, take the bumper of don't be lazy

[@Star-Performance_]

@Jonathan English aha I see what u mean now, you can, check a comment in one of them he explains how to

[@Star-Performance_]

@Jonathan English no problem I hope it works out for you good luck

[@dunebasher1971]

To apply the mesh to the front of the hole, you have to use a hammer to intentionally dent the area around the hole and create a "recess" for the mesh to sit in, so that the surface of the mesh is flush with (or even fractionally below) the surface of the rest of the panel.

[@Iazzaboyce]

So the filler you use first is B and the filler you use next is A...

[@shaikabdulkhader999]

SUPERB BUT METAREAL NAMES AND SALE OF THE ARIA

[@mintuverma7534]

Hot satepler kit l.d.h markit plastik bumper car

[@PeteR-or5kj]

Isn't it so easy when the panel is off the car...

[@Evanescence29]

After the procedure,The car looks scratched though!!

[@dtroystopper2]

That's why you use the finer grit sandpaper, and the sanding block.

[@dunebasher1971]

As said, you have to use finer and finer grits of sandpaper to get back to a perfectly smooth surface. It takes time and elbow grease.

[@pedro75392]

Add more coats

[@next0845]

Aluminium mesh - Steel panel Google, dissimilar metals 😂

[@NeoJSsk]

And let me guess it cost about a $100 dollars

[@frankyalvarez7160]

Let me guess, a new door costs about $800.

[@radepetrovic9182]

@@frankyalvarez7160 800$ for a door?

[@dtroystopper2]

40

[@dunebasher1971]

At current UK prices, the kit is the equivalent of $50 US.

[@Shanedog76]

that stupid? it says squeeze 'all' of the body filler out of the tube if you only need a small amount??? every rust hole size will be different sized? and instead of hand sanding it, why not use an electric sander?

[@RickAnderson1]

do you really have to pronounce "alluminum' alluminIUM? You can't just throw a fkn I in there.

[@stevebevan5104]

Of course! Line B before Line A