Isuzu npr 2012 rear lugnuts

[@bobcat8439]

Them lugs never come easy

[@ricfairfaxfc4017]

How do you remove outer lug when it is stuck to the inner lug? Inner lug just comes off - inner/outer lugs sandwiched on the wheel.

[@herpabetic]

Is that 1 you're honestly probably going to have to cut off with a diagrander or small grinder unless you leave that log for last and get the rest of them and bring that 1 out with the wheel but you will still have to cut it apart when you get the wheels off

[@leakers69]

Thank you for the video! I have two questions, why didn’t you put compound on outer lugnut and are you supposed to torque in both iner and outer lugnut. Thank you.

[@herpabetic]

I use antiseeze and been set at around 120lbs on lugnut torque..sorry missed adding that to the video

[@melloneemcdonald3767]

Can you do a video of changing them studs? I just bought one and three are stripped.

[@herpabetic]

Alot of heat..maybe a good hot one..not a cutting torch get hot then smack them with a hammer good ..just remember driver side is reverse thread

[@easydoz1]

New tire next to a used tire... Job security right there...

[@GX--X01]

Do you know where I can the rubber stopper so the frame of the truck doesn't touch the axle?

[@herpabetic]

That is probably gonna be an isuzu order.. But to be honest most of those bump stops are very similar you could probably still some off of a lot of bigger truxtun in the junkyard

[@thedude2820]

Why are you the only one I’ve heard about lug direction from?? Thank you, it’s stuff like this that some ppl appreciate the transparency you seem to give us. I, appreciate it anyway… I’ll say I’m far from perfect and if other vids I watched from other providers mentioned it, then I must of momentarily stepped out every single time they did and you were the guy I didn’t ….. yeah not likely but I’m tryin to be nice. Anyway thanks. It’s the different stuff like that that gives me pause working on my 05 w4500 gmc (gmc by name only essentially, I think) any cautionary or informative info with alternator (w/vac pump)swap a guy could use??and if you have one and I already fk’d something up with it do you give estimates😬 I’m local to you.

[@herpabetic]

Well thank you I appreciate when people appreciate what I do instead of put me down because the simplest thing honestly I look on their channels after and I wonder why they didn't make the correct video if they're so perfect all I can do is try and I appreciate people like you thank you

[@herpabetic]

I've got a guy set up for AC over here in Las Vegas I was in Tacoma Washington but if you need the info I'll get you over to him I'm decent at it but hes better

[@thedude2820]

@@herpabetic I got questions tho…. Lots of questions, lol. First would be where is my spin on fuel filter on my w4500 gmc (5.2L turbo 4cyl Isuzu engine) I’ve looked and looked and can’t find it, is it in part of the engine housing or???

[@herpabetic]

There is one behind the driver side wheel just behind it short fat one the other one is on the motor normally metal about a foot above the other one almost by the top of the motor but both on driver side

[@brownpeanuts5716]

I guess he doesn't need to use a torque wrech on the inner lugs? What is this back yard mechanical?

[@herpabetic]

No..i am a magician..lol..jk yes I know and it was a a short video a long time ago. I'll make another video down the road

[@roversnolan1]

Do not use antiseize on the inner lug. Thats just asking for the inner to spin when trying to remove the outer.

[@MyJuarez77]

Where can I get the cap Threads Looking for socket 1" Drive to 19mm square?

[@herpabetic]

Got mine from napa auto parts

[@MyJuarez77]

@@herpabetic what size is your?

[@herpabetic]

@@MyJuarez77 41mm ×21 s

[@GX--X01]

What socket part number did you use for the inner studs?

[@herpabetic]

I'll check my socket and see if there are any numbers

[@GX--X01]

@@herpabetic thanks!!

[@herpabetic]

I'll have to get the socket from work ....thought I have one in my box truck but I dont....the square one right?

[@GX--X01]

@@herpabetic yeah

[@herpabetic]

Have it to you in the morning..going to work around 5 am

[@Shello89]

What is the size for the lug nut of that vehicle

[@GX--X01]

41mm and the rear lugs have square fitting

[@leov2063]

Okay so 41mm for the outer. Do you know the size for the inner square drive?

[@GX--X01]

@@leov2063 Sunex 54121 1" Drive Combination Budd Wheel Impact Socket 41mm x 21mm

[@mxr618]

@@GX--X01 Thank you!

[@bobcat8439]

The mamalukes made hard on round eye

[@buden33]

Is it the same for a 2005 gmc w4500

[@herpabetic]

Not sure on that one but I know the isuzu's are reverse thread on driver side

[@bobcat8439]

Spud socket

[@bobcat8439]

Isuzu

[@herpabetic]

Yessor npr hd...yea no fun sorry about the late reply...been slammed

[@fanettakeener3421]

Start using plain identifying words like "clockwise or counter clockwise"

[@herpabetic]

OK I'll try to be alittle....better

[@bobcat8439]

Garabage