Water in the engine - Water can get into your oil sump in two ways: Water in car - Water condensation in cold air or combustion gases: this phenomenon is extremely rare and only occurs at specific temperatures.Water in the oil - Coolant leak due to non-watertight seal (cylinder head gasket, etc.).
@custommadeknives5 жыл бұрын
You need to get it welded properly. It came out due to a fault with case housing not being strong enough to handle the compression stroke on the kick. It blew the bolt hole out and if you jb weld it, first or second kick it's gunna blow out. Get a new case I've had it happen and tried this. You guys rock keep up good work bro.
@glynroberts30055 жыл бұрын
You should of washed it first
@NeilEAnlin5 жыл бұрын
The more difficult rebuilds you take on....the better you skill yourself! You're becoming a KZbin sensation. If you keep at it.....in 2 years you'll be doing full rebuilds in a few days like it's nothin. Then you end up with a title that goes with your name and that's "he's good!" Good money in full rebuilds. Really good money! Anyway, hope you're enjoying the weather and ripn it up!!
@troycrowder99425 жыл бұрын
the trick with jb weld is ruff up the surface make dam sure no oil is on any of it do not even let your finger touch scratch the case in two directions apply it in thi coats get the quick set about 5 layers with a small stiff brush and you start n the middle and work your way wider with each coat the overlap makes it real good also after you're first that fiberglass cloth works well on big holes put it on your 2nd coat looks like you have a nice kdx you should be able to fix it just take your time good luck
@2strokemxclassics5 жыл бұрын
U have to take the bottom bolt off the water pump to drain it make sure radiator caps off when u drained coolant
@marksabean66735 жыл бұрын
Get a 350x
@spencerhewes57775 жыл бұрын
I had a similar problem with the case breaking. I think your issue was that the big spring has an end that is bent to fit into the little hole on the top of the case surface. I think it slipped out of the hole and when it was kicked the spring flew into the case, causing it to break out like in the last video. Also that small arm next to the kick starter gear should be bent and is not the issue. Best of luck hope I was able to help out!
@2vintage5 жыл бұрын
Thanks!
@dellc15215 жыл бұрын
Will be a fun bike when done needs a really good clean
@nipseyhussle83675 жыл бұрын
Wicked cool rare little bike. Good deal, keep up the videos!
@devonpiper53425 жыл бұрын
What I would use to fix that is a good lil size chunk of quick steel! Just used some quick steel to fix a broken lip on the crank case of my 2006 kx450f
@everydaymechanic46575 жыл бұрын
Go to harbor freight you can get aluminum brazing rod ....but you have to split the case and pre heat the whole thing. I used a bbq to preheat a blaster case and it worked perfect
@Phil2stroke5 жыл бұрын
jb weld and wire mech on the outside coated in jb for extra strength clean and sand the surfaces!
@augieh61465 жыл бұрын
Yessss dude. That purple is gangster I love this year
@gtisid5 жыл бұрын
the bit you are looking for is what got behind the kickstarter gear and blew through the case by the looks of it. that’s an annoying break, it’s great when a bodge works forever
@lazarmrsic56235 жыл бұрын
Try aluminum welder bc I had 2 raptor 350s that the case broke bc of the chain snapped and I used aluminum welder and It worked now I use case savers on my 400ex
@backwheelbandits2805 жыл бұрын
I got my 80 for 250 its rips..rebuilt it after 6 months ...don't think I have the hearth to let it go.
@devonpiper53425 жыл бұрын
Jb weld does hold! I owned a raptor 350 before and the same thing happened chain snapped put a hole in the motor, used a lil peace to cover the hole and jb welded it, and it ran for as long as I kept it
@donniewright22005 жыл бұрын
I had the same bike big hole in the case patch it with aluminum pop can and jb weld held up for years still holding as far as I no
@quadadiks60495 жыл бұрын
I have a kx85 in purple it is so fast
@roadrideking67075 жыл бұрын
Any purple bike rips
@tmac15725 жыл бұрын
Honestly you should just weld it. Its not that much work and you dont need to tear the motor appart. JB weld will most likely work fine but if you actually weld it it will be 100 times stronger
@gabewilliams59935 жыл бұрын
The Liberator I don’t disagree that an actual tig weld would be stronger, but I think jb weld is way stronger than necessary and it will suffice just fine for that piece.
@michaelholden86675 жыл бұрын
The sixth number of the serial number is the model of your bike not hard too find out don't use no job weld get the side cover used or new hope you the best good luck my friend
@4x4monteforlife545 жыл бұрын
Use quick steel my buddy broke his case on his Yamaha Warrior 350 and it's about the same size hole we put quick steel on it and it's still running its been a year of relly hars abuse and two top ends and its still holding good
@brycehoskin28154 жыл бұрын
Awesome Chanel been watching for a while now keep em coming 🤙
@jamieryan57035 жыл бұрын
Hello best of luck with the bike
@andrewevans71815 жыл бұрын
Their is this putty stuff called jb steelstik an it works great for patching holes,an its alot easy to use
@ilogicalthegoat97345 жыл бұрын
It’s the water pump seal for sure lol I just bought one kit comes with bearing for the pump it’s self ..
@HUSKY7-15 жыл бұрын
First to hand crank to test the compression
@turtlegames69385 жыл бұрын
Your bike collection is minty
@chillerstv22185 жыл бұрын
Let’s just assume this bike is held together by JB WELD
@BrokeFolksMoto5 жыл бұрын
U can use aluminum tape for duct work to put over the hole..the tape will create a wall for the jb to ahear to..remove Kickstarter gear, then jb weld outside and inside of the case..hope this helps. #brokefolksmoto 😎
@matthewgrimes41295 жыл бұрын
Hey guys the jb i dont think would work being right on a bolt hole when u go to torque it down beings ur gluing and thred hole back on to the casing when u go to tighten cluch cover to spec i believe it will brake the jb with all the tighter pressure being on it it may work ive had success with jb welding my water pump cover on my rm 80 and it held good to the pressure but only i believe its 8lbs of pressure that rund in the radatior so not much at all you can more than likely get a crank casing off ebay for cheap i just bought a kx65 whole transmission for 60$ look on Ebay for the part i would. over all nice bike dig the purple years kx one way or another i got faith in yall she will be ripping next week
@merlinmoulton9185 жыл бұрын
I'd jb weld the pices back on and pretty sure that peice of metal for the kicker you thought was bent is supposed to be like that, i think that piece on my 2003 kx 85 looked the same as that and works fine
@martin65855 жыл бұрын
You can JB weld the engine part, it will work vell, because there is no perssure in the oil pit.
@Kaelan5145 жыл бұрын
I might start making videos like this not sure. I always have a new project. Just finished a kfx450r. Working on few different things now. Here's my collection: 2017 Raptor 700, 2008 kfx450r, Blaster, crf230, xr70, xr50, a ttr125, and another ttr125. I think that's it idk lol. I'm only 15 lol
@ThatBlueHoe2 жыл бұрын
Lmao seems like you have quite the collection, I'm 14 and I only have a kx80 and it needs alot of stuff lmao
@jeffferguson8995 жыл бұрын
I would ask Jade what she thinks about jb welding the case.
@codyweien45134 жыл бұрын
Is he saying JADE WELD? lol
@jimmyliuni17215 жыл бұрын
I need to be more like you and be able to flip things but I get attached too easily like right now I have a 71 cb450 a 86 it200 a 85 it200 86 DR 125 a 2001 Yamaha Blaster and a 1970 CT70 but I've decided to get rid of the CT70 and the DR 125 and possibly the blaster but I don't know how you just get so many cool projects like the LT 500 and just let them go but I'm starting to realize that I could just get something just as cool or better keep up the awesome videos
@michaelholden86675 жыл бұрын
Replace the case if you weld it want last long and might destroy the parts inside because of the heat from welder fix it right its worth it I'll buy as is and pay for shipping out of north Carolina let me no thanks
@mattyboy31575 жыл бұрын
I love your videos you are amazing I wanna buy your bikes
@RealSuburbanCowboy5 жыл бұрын
Maybe you can try that "low heat" aluminum welding rods from Amazon? Do yourself a favor and pressure wash those machines before you work on them. It will help keep crap from getting inside the engine.
@jakemcdade39825 жыл бұрын
You should try to find a Honda xr250r I have one and it is fast and fun
@Watchdog-jd5pp5 жыл бұрын
Considering it’s a decently rare bike i think you should weld it or get a new case
@jsc6165 жыл бұрын
Watchdog 1021 I like your profile pic
@NeilEAnlin5 жыл бұрын
Ok good....you just said it was the second one. I guess I should wait until the vlog is over.....lol
@jacoblawliss56945 жыл бұрын
Sick bike, just picked up a 2001 yz 125. Wondering if you have a carb for it. I can’t find a OEM carb on eBay
@whyettjensen32925 жыл бұрын
Look at a lectron carb. A lot better than oem
@Brensta185 жыл бұрын
Awesome video bro bro
@joesheward74315 жыл бұрын
Had exact same on my bike with the oil, its the water pump bearing
@michaelbiel74735 жыл бұрын
Water pump seal
@joesheward74315 жыл бұрын
Michael Biel same thing
@loganshell20035 жыл бұрын
Cool cant wait!
@kurtgandarillas86185 жыл бұрын
Water cannot get into the oil from a bad head gasket on a 2 stroke. 2 separate compartments. That is why you have to mix oil with the gas on a 2 stroke. It is a bad water pump seal.
@lancewashington39105 жыл бұрын
JB weld it or just tac weld it
@slushbud_2145 жыл бұрын
That oil looks cool
@OO-mo8mr5 жыл бұрын
That is super milky holy cow 😂😂
@dirtbike4345 жыл бұрын
thats gonna be tough because the kick start gear moves and there isn't alot of room for extra j b weld
@NeilEAnlin5 жыл бұрын
Joe.......please tell me this is the second kx80 you've done....!!?
@BikerBoyL5 жыл бұрын
It’s so hard to find clutch covers for those bikes I have a 1997 kx100 with a purple seat and it has a single piece clutch cover and it cracked bad and the bike is pretty much done so I gotta get a whole new motor
@nategroovy62675 жыл бұрын
The reason kickstart won’t come back is spring it happened to mine
@rockfordriders71925 жыл бұрын
Looks like a shamrock ☘️ shake with caramel
@mrlanemichael5 жыл бұрын
I Thot u couldn’t mix match cases or is that only for certain makes and models
@mrlanemichael5 жыл бұрын
I’m just getting in to this type of stuff I just heard that most cases are specifically fitted for the engine it came on . Like one of my old revolvers I got extra parts for it and even though they are from the same exact gun the plate to cover up internals just would not fit
@jacksonkoehn30845 жыл бұрын
Sweet little bike!!
@Bonde-pg2gz5 жыл бұрын
Can you teach me how to fix bikes? I am so bad at it, and i need help to get better.
@doctorsleep27865 жыл бұрын
My advice would B is to take motor out and get it Tig welded.do it half right ..lol
@gavinvanwinkle41075 жыл бұрын
I used to have a green 2003 kx80 but I let my friend ride it and somehow he made my chain fly loose, wrap around the sprocket, and take a huge chunk out of the trans cover, he also popped a stick up through the forks and broke the fork seals
@portablezaps65175 жыл бұрын
Dam
@mikeyboost4life695 жыл бұрын
best of luck with everything man but you still have a major issue cuz there's a lot of antifreeze in that oil which obviously you can see but all I'm saying is just cuz you fix the case it's not going to be minty you there's still a big problem going on
@backyardmec23485 жыл бұрын
I got a 1999 kx 80 I need to know what gear oil do I put , 75w 90 or 80w 90 ?
@Mk7adxm5 жыл бұрын
nice i have a 2001 yz 125!
@JourdonGulick5 жыл бұрын
You should check out my yz125 build 🤘
@bryanguise60115 жыл бұрын
That piece that cracked off the gear is probably what busted the hole in the case.
@kgthegreatone9435 жыл бұрын
I need to move to Wisconsin
@JaxStifler5 жыл бұрын
Welding that hole
@jaypearce61995 жыл бұрын
Great vid dude 😎
@Loke250 Жыл бұрын
I have the same bike and i have a question. Why is the bike rare?
@broadday-motomax-27705 жыл бұрын
Do you ever keep anything ?
@simonmatus49855 жыл бұрын
If I were you, I'd buy and replace both pieces of case. I think that after some time there will be oil leaking in place where u want to JB weld it.
@chs183115 жыл бұрын
That's it; I'm boycotting until Jade comes back!
@2vintage5 жыл бұрын
Next week!
@m8fusion7123 жыл бұрын
I've been there & good video
@kamchamness50005 жыл бұрын
Is the bike a 2 stroke or 4 stroke
@gavinhook48735 жыл бұрын
I would have someone weld it. it would be a much cleaner fix.
@bugzbunny32234 жыл бұрын
But he has no interest in doing that, he will epoxy it and flip it for 400 percent profit to some poverty line family that wont be able to afford to fix it properly and he can buy it back for 200 and epoxy jt and do the same again
@bugzbunny32234 жыл бұрын
And then... he will make a killing on us watching the video of him brag about making dumb money from shit bikes.
@lukecombs56595 жыл бұрын
Yea man always clean it before you tare into it or all that muck will end up in the motor
@ForrestJones2145 жыл бұрын
You can have it welded and sanded and if it needs a gasket you will be able to buy a new one and it work Edit: as I submitted it you said my idea😂
@niels34265 жыл бұрын
I have a Kawasaki kx 80 1997
@rictan68663 жыл бұрын
kickstart boots pedal fun ride
@callummackay48635 жыл бұрын
Good luck trying to seal the cases welding on a gasket surface it will never be perfectly flat better off tearing the bottom end down and doing properly
@MisterdionneYT5 жыл бұрын
try cr500 vs crf450r drag racing please
@jaypearce61995 жыл бұрын
You maybe able to reuse the waterpump seal for now, the little spring circle that goes around it should split apart, you can then chop a few mill off of it to create a tighter seal on the shaft, this trick is also very effective on leaking fork seals! Ive just dont this on my 2017 ktm exc 250 and no more weeping from the fork seals..
@bertrandbloodman5215 жыл бұрын
Please in your next video say what type of oil you use in the moto4 80
@coletrick87485 жыл бұрын
It will take one to two hours to pull that motor... Have it welded professionally... Jb weld is most definitely a temporary fix.
@josha55635 жыл бұрын
Nice Polaris atv and nice bike keep up the good videos
@xd_armyelite4785 жыл бұрын
Atvs are junk
@michaelstarr7681 Жыл бұрын
It will be fine
@stevenboatright54885 жыл бұрын
It’s supposed to have that “bent” bar my 94 kx 80 has same thing you have a broke kick start shaft the gear doesn’t have the lip that catches on “bent” bar to keep kick start from over rotating. @2vintage
@2vintage5 жыл бұрын
Thanks, very helpful!
@702clapped75 жыл бұрын
Show us your collection of bike
@zacklataille3425 жыл бұрын
Get it welded if anything don’t jb weld it jb weld is only good for certain stuff
@corey4c1055 жыл бұрын
Jb weld will work
@jackgardthman42515 жыл бұрын
Ive got a purple 96 too
@landong21205 жыл бұрын
I saw my comment
@joshlucaa36875 жыл бұрын
Make shure u rinse the motor with new oil
@troycrowder99425 жыл бұрын
if the aluminum has any oxidation jb will not seal
@rageagainstthetoymachine24105 жыл бұрын
holy shit I've never seen oil that milky before
@kawasaki_love2 жыл бұрын
💎
@megamindtvsydney39673 жыл бұрын
This bike is $2500-$4000 if mint in Sydney Australia and reality like new can ask big money
@joshvaz025 жыл бұрын
Needs water pump rebuild
@alexbrand71815 жыл бұрын
yea probably water got in, thats when oil turns white, jet skis are awful about doing it and then shooting it out and smearing it all over the side
@c52ned5 жыл бұрын
Seems like the clutch is slipping
@MOranstock4 жыл бұрын
You should powerwash before you start taking stuff apart. All that dust and grime going into your motor