Can You Deck A Numbers Matching Engine Block?

  Рет қаралды 435,411

Jim's Automotive Machine Shop, Inc.

Jim's Automotive Machine Shop, Inc.

Жыл бұрын

Head to squarespace.com/jimsautomotive to save 10% off your first purchase of a website or domain using code jimsautomotive
There was a lot of concern in the comment section of the first video in this series about how we could deck the block and save the numbers... Here's how!
Instagram: @jamsionline
Facebook: JAMSI Online
TikTok: @jamsionline
Website: www.jamsionline.com
For business inquires: Contact info@jamsionline.com

Пікірлер: 453
@JAMSIONLINE
@JAMSIONLINE Жыл бұрын
Head to squarespace.com/jimsautomotive to save 10% off your first purchase of a website or domain using code jimsautomotive! As you all know, when you support our sponsors, you are directly supporting our channel and future content! We have been a Squarespace customer since 2015!
@guysumpthin2974
@guysumpthin2974 Жыл бұрын
Std bore 396 will over heat the rings , the average wall thickness is too thick , the coolant doesn’t effect the wall enough, which is why later chevy made them into 402 with the 396 badges still on the cars. The same effect happened in the 283 , although the wall thickness varies SO much in those engines
@guysumpthin2974
@guysumpthin2974 Жыл бұрын
People have been decking those blocks and re-stamping those numbers for over 40yrs
@JohnH20111
@JohnH20111 Жыл бұрын
if i ever need any engine work done, i’m going to bring it to you, because y’all do high quality work and all
@MacPoop
@MacPoop Жыл бұрын
In my own experience those GM big blocks weren't exactly square and true or even totally flat right out of the factory, early ones were probably the worst. You've done a great job getting that block right! 👍
@JAMSIONLINE
@JAMSIONLINE Жыл бұрын
Thanks!
@MacPoop
@MacPoop Жыл бұрын
Now he can run aluminum heads on it and not constantly blow gaskets anymore thinking the heads are bad 😎 I've still got a Ford head I'd love to mail up there for a total rebuild - good machinists are hard to find in my area
@shadvan9494
@shadvan9494 Жыл бұрын
in my own experience with chevy big blocks, I have seen the decks vary from side to side by as much as .015 on the stuff made in late 60's early 70s. but there was a lot of meat on the bones of the old big blocks. the was 1 particular 396 block casting that shared the same cores with the 427 of that era. I dont remember that particular casting nubmer ritgh now but the cylinder walls were super thick. you could bore them out to 4.310 without issue. that is a 0.216 overbore! the stuff made in the mid 70's was better machined, but they took out most of the beefyness to those big blocks to save weight. the Gen V blocks are usually within a few thou of each other. they really got their crap together with machining and the Gen V blocks.
@MacPoop
@MacPoop Жыл бұрын
@@shadvan9494 yeah those early ones were a bear right out of the box, no 2 blocks would even measure the same. Intake manifolds wouldn't fit quite right. Not bad but not right. You'd have good intake gasket squash on one end, hardly any on the other. Without doctoring forget about aluminum heads on the early ones, they'll blow head gaskets overheated just a little just once
@petermolnar8667
@petermolnar8667 Жыл бұрын
@@MacPoop why is it just the aluminum heads by the way?
@maggs131
@maggs131 Жыл бұрын
That tool you used to bring the sleeves into the correct diameter isnt boring, its rather exciting
@andoletube
@andoletube Жыл бұрын
haha😅
@christianpaulroldan4010
@christianpaulroldan4010 Жыл бұрын
😂😂
@williamorton7600
@williamorton7600 Жыл бұрын
I appreciate that you're taking the time to keep as much metal as possible for that original block. Very professional.
@paulmathews5686
@paulmathews5686 Жыл бұрын
I was one of the guys concerned with the numbers being wiped off . you had to take the time to set up the machine , and then finish with a hand file on the top edge. that's all you could do , & that was for sure the " MONEY SHOT " there on those numbers !! you wouldn't believe how many times over the years I asked the machine shop to do what you just did , and they would say , yeah ,sure , okay , no problem !! then you get the block back , and the lazy sack of shit , wouldn't take the time, like it would of stopped the whole shop from running if he did what you just did !!! THANKS FOR TAKING THE TIME , I'M SURE YOUR CUSTOMER APPRECIATES THAT !!!! 2 THUMBS UP , KEEP UP THE GREAT VIDEOS !!!
@bryancohn9406
@bryancohn9406 Жыл бұрын
I’m always amazed at how inexpensive engine machine work can be given the cost of machinery, time and most importantly knowledge required to do the job properly. Having had machine work done for dozens of various racing engines used in road racing over my 36 year career I enjoy seeing the care and expertise you put forth.
@CodyMcGriff
@CodyMcGriff Жыл бұрын
Even a million dollar machine can only charge so much per hour or the business model won't work, longer ROI, debt is a tool not a burden
@sc358.
@sc358. Жыл бұрын
​@@CodyMcGriff what kind of ROIs do you see for different pieces of equipment?
@rollydoucet8909
@rollydoucet8909 Жыл бұрын
Competition from other shops was the main reason for inexpensive machine shop labor rates. Barely breaking even seemed to be the "norm" for decades. Today, there are fewer shops due mostly to the fact that the auto rebuilding industry is not what it once was, with fewer people keeping cars for long periods of time. Our shop has survived well on performance and light industrial services, and we're constantly adjusting (raising) our hourly labor rate to meet the cost of being in business. At the end of a day, week, month and year, we're just breaking even.
@CodyMcGriff
@CodyMcGriff 11 ай бұрын
@sc358. I have no idea but I'm sure some quick Googling would help determine that but you would need a full machine shop to get started remachining engines, I would start by working for a master machinist and learn from the bottom up, pick the masters brain and go from there 🧠
@CodyMcGriff
@CodyMcGriff 11 ай бұрын
@sc358. this could depend on cost of machine and how often you use it vs. How much each machine can justify per hour charge for instance 10% of a machine shop can pay off the whole machine shop, I went to college for manufacturing and we used the welders and wire wheel 80% of the time and the lathes just sat there, not good ROI, much more skill and precision involved so do your homework before buying any piece if equipment. My vote for anyone is to pay for chatGPT 4 for a month and ask it all sorts of question such as you are asking me, it has helped me indefinitely build websites, apps, SaaS and apparel brands and it will only get better, get work !
@MrCyborgAlien
@MrCyborgAlien Жыл бұрын
Love the channel. I appreciate that you take extra time out of your day to do premieres and interact with the community as the video is played.
@Charlie-wr6dy
@Charlie-wr6dy Жыл бұрын
Beautiful job on that block, and your explanation of each process makes this channel so great to watch. BTW, we saw the cleaner playing with some of the machines while you were away, I hope everything was in order when you got back!
@OlSgtLove
@OlSgtLove Жыл бұрын
Always enjoy watching your channel and the attention to detail you and your Dad do . Excellent work everytime.
@JAMSIONLINE
@JAMSIONLINE Жыл бұрын
Thank you!
@thecanadiantradesman7916
@thecanadiantradesman7916 Жыл бұрын
Nice to see the level of care and craftsmanship your shop takes. You never really get to see this when you take your parts to a shop. They may not be special or irreplaceable to the shop but are always the only thing you care about and hope the shop treats them the way you guys do. Keep up the good work and thanks for showing us there are people out there that still care about the work they do and the customer.
@lukewise1227
@lukewise1227 11 ай бұрын
I restore vintage and classic motorcycles in my retirement (early due to health) and I get great enjoyment from these videos, however I do suffer 'machine shop envy' for a day or two after. I wish I had your space, your machinery and your cleaning assistant to offer advice. If I am struggling with something and need a break, your videos are a great inspiration to get back to the problems at hand (75 year old motorcycles inevitably have 75 years worth of bodgy repairs). Keep up the good work with the videos, it never gets boring for a fitting and machining nerd. 👍 😊
@ronmurphy9819
@ronmurphy9819 Жыл бұрын
To me you have the dream job! If you love it and it’s fun then it’s perfect. I was an engine man in the US Navy. I loved it, now I’m trying to learn some machining. I’ve got a mill with a 49 inch table and a lathe. I had some machinist friends and would like to think I learned enough to be dangerous. Thanks and keep them coming . I like learning new things. Thanks Ron
@erich6860
@erich6860 Жыл бұрын
After a few years making cylinder heads, I find this particular operation amazing. A cutter that large with a single blade. Such a good finish. I"ve seen worse finishes with 30 plus inserts and a wiper blade.
@jayss10
@jayss10 Жыл бұрын
Good to see this old girl coming back. One thing I would strongly suggest. Please check all the lifter bores if you haven't already and make sure you have ample clearance with the replacement lifters. I'm assuming the customer is ether going to go with a solid flat tappet or a hydraulic flat tappet camshaft. Anymore these flat tappet motors have a hard enough time breaking in the camshaft, I wouldn't want to give this old girl anything to complain about.
@JB-fn9lb
@JB-fn9lb 10 ай бұрын
Great content. I can't help but find irony in the length of Stanley(?) tape measure you use with the hook still attached to indicate some depth measurements given all the precision measuring tools available and the efforts taken to ensure accuracy and end quality. No big deal as the measurements gives the required resolution for its purpose, just find it humorous. Thanks for making and sharing all the good videos and keep up the good work.
@kevowski
@kevowski Жыл бұрын
Your videos are one of the few I fell compelled to watch from start to end (except the sponsorship) brilliant 👌🏻 Thank you for sharing 🇬🇧
@bigblocklawyer
@bigblocklawyer Жыл бұрын
Dave Crume, who built engines for Bo Laws for years did my numbers matching 396/ 325 from my dad's '65 Impala SS, my '66 Corvette 427/450 and my '67 Corvette 427/435 blocks and he decked them and saved the numbers on all three. Years of hard use and never had an issue.
@craigm.9070
@craigm.9070 Жыл бұрын
Excellent video! Thanks for explaining the math on this project; your customer should be very happy with your thoroughness. Looking forward to the assembly, I haven't done a BBC assembly in quite a few years now.
@roccomicelotta3798
@roccomicelotta3798 Жыл бұрын
Great video! This was my first time on your channel and certainly not my last. You explained this process so well that I almost feel I could do it. Thank You, Ric
@davidfox9100
@davidfox9100 Жыл бұрын
Such an amazing video and channel I love how detailed you are and how in depth you go with your explanation 11/10 recommend to anyone.
@erniecamhan
@erniecamhan Жыл бұрын
So enjoy watching a true craftsman at work 👍🏴󠁧󠁢󠁳󠁣󠁴󠁿
@drewwatkinson6604
@drewwatkinson6604 Жыл бұрын
Love the work that you do, so satisfying!
@davidblain2714
@davidblain2714 Жыл бұрын
Thanks buddy! I'll say it again, just love being there in the shop!
@jamiedhuskey6643
@jamiedhuskey6643 Жыл бұрын
I’m totally involved, dig the channel
@brucemadden1626
@brucemadden1626 Жыл бұрын
Hey--the "Cleaning Guy" did a nice video while you were away. Hope you gave him a big Xmas Bonus and maybe even a raise for 2023?
@klmorris1576
@klmorris1576 10 ай бұрын
I love this channel. I like the care and concentraton you put in every project.
@thekracken4572
@thekracken4572 Жыл бұрын
Why do find this entertaining as hell? I'm not a Mechanic or Machinist. I'm not even a car guy really. I can watch this for hrs!!
@Rocketman88002
@Rocketman88002 11 ай бұрын
Nice presentation! Unobstructed video clear audio and guidance throughout the process! Not much has changed since the 60's really considering the history of machinng prior to the 60's. Its still all about the operator. Machines, metals, materials and technology have evolved and blended to make available better priducts.
@jaredburns6652
@jaredburns6652 Жыл бұрын
Ughhh 11 minutes I can’t wait. Best machining channel on here
@Duh6666666
@Duh6666666 Жыл бұрын
I also really enjoy CEEA and IC weld.
@rogermontee8264
@rogermontee8264 Жыл бұрын
Excellent work on the big block!!!!! Thanks for sharing.☺️☺️☺️👍👍👍👍🇺🇸🇺🇸🇺🇸
@rotax636nut5
@rotax636nut5 Жыл бұрын
Quality work, you are on the road to achieving perfection, keep it up and one day the world will beat a path to your door..
@michaelthorne5441
@michaelthorne5441 11 ай бұрын
Learned a lot from this video, hope you have more
@dwaynepuckett16
@dwaynepuckett16 Жыл бұрын
The cleaning Guy did great job while you were away, give him big thanks.
@alwayssearching1882
@alwayssearching1882 Жыл бұрын
Another great upload boys!
@roberta4989
@roberta4989 11 ай бұрын
Really great content. I am a retired mechanic and watching this brought back memories of fun and had work.
@rharris1336
@rharris1336 11 ай бұрын
I miss the smell of honing oil. 😂 Amazing how much more accurate the machines are than the machines I used in the 80s. Rottler boring bar (no CNC or digital read outs) and Sunnen cylinder king hone. We didn’t even use a torque plate. Back then, we were all used to pulling into a full service gas station and the attendant checked the dipstick and told you how much oil you burned or leaked between fill ups lol. Nice precision work 👍👏👌🏻
@ronbunker5778
@ronbunker5778 Жыл бұрын
I love this stuff! Nice job!
@juliejamison8059
@juliejamison8059 Жыл бұрын
Yep that's my engine. Can't wait to here it run those boys do a hell of a job!!
@Musicmainn
@Musicmainn Жыл бұрын
What a great way to end the day! Its night here in Norway! Good job!💪and good night!😉💤👍
@JAMSIONLINE
@JAMSIONLINE Жыл бұрын
Thanks for staying up to watch!!
@clydegreenwood5673
@clydegreenwood5673 11 ай бұрын
I like watching your videos you learn something
@davidstewart3868
@davidstewart3868 Жыл бұрын
Terrific work!
@GrandPitoVic
@GrandPitoVic Жыл бұрын
Very nice brother. I enjoy watching machine work
@tbirdracer460
@tbirdracer460 Жыл бұрын
I love this channel. Great work! Thanks for sharing!
@brentwinkelman1990
@brentwinkelman1990 Жыл бұрын
Really enjoy the content...wish i would have went to engine building/machine school instead of auto tech for college...enjoy precision measurements/equipment and the overall engine machining/building process a ton
@Lure-Benson
@Lure-Benson 10 ай бұрын
I really like the old Chevrolet 396 and the 402. I owned a 1972 3/4 Chevrolet truck with a 402 that was unstoppable and a beast in power and now that same 402 is in my guide work boat jet boat living a new life as a marine motor.
@happydays8171
@happydays8171 11 ай бұрын
Anybody taking a block to you is getting so much more experience per dollar spent compared to most shops.
@rogerturley
@rogerturley 11 ай бұрын
When my guys in Provo retire, I may have to make the drive to Gill. I'd trust you guys with my race engines any day.
@markblundell9461
@markblundell9461 11 ай бұрын
Watching this , I just realized what I should have been doing for my life’s work. Being a machinist and a mechanic! Oh well too late now 🙄.
@MrBlackbutang
@MrBlackbutang Жыл бұрын
Good to seein Neil and Bob are hard at work there
@saltycreole2673
@saltycreole2673 Жыл бұрын
Nice to see young folks doing this work. Many (Too many) times you see us old, nearsighted, potbellied grayhairs doing this work. Much respect.
@charlieromeo7663
@charlieromeo7663 4 ай бұрын
Here here! My buddy operates an engine machine shop and can’t find anyone south of 40 years old that wants to learn this trade. I guess it’s because fewer kids are into automotive related work and tinker with their own vehicles and don’t want to get dirty. There’s very little grease and grime on keyboards, iPads, and smart phones. Keep up the great work and quality videos. I will watch them as long as you make them.
@wilsonlaidlaw
@wilsonlaidlaw Жыл бұрын
I hope the owner of this block watches this video and appreciates the lengths you went to, to get a perfect final result.
@1971VoiceoftheMummy
@1971VoiceoftheMummy Жыл бұрын
Nice work!
@bowtiedone2784
@bowtiedone2784 Жыл бұрын
It's amazing when you do this to a block and mill the heads and balance the rotating assembly then see the difference in just how smooth and responsive that engine is.
@aulaseduardocurvello679
@aulaseduardocurvello679 Жыл бұрын
Excelente machines and good knowledges technical.
@johnnystanley4469
@johnnystanley4469 Жыл бұрын
Very nice work.
@michaelprue9024
@michaelprue9024 11 ай бұрын
Nice work 👍
@dalemiller4457
@dalemiller4457 Жыл бұрын
Really like what you are doing on this channel, just wondering after decking the block, do you have to take any material off the top of block for intake manifold to seal properly.
@ercost60
@ercost60 11 ай бұрын
Great video. 3:32 That 1/16" tape measure used for depth of cut is a funny contrast to all your other precision tools. :)
@michaelthorne5441
@michaelthorne5441 11 ай бұрын
tdc is usually within that range
@oceanmariner
@oceanmariner Жыл бұрын
I've rebuilt dozens of engines. Mostly marine diesels, but also racing and aircraft. I originally learned on aircraft radials. It's not surprising the block decks don't match or are out of square. It's been my experience that a good machine shop does a much better job than the OEM. The OEM only worries about the block falling with their wide tolerances. A good machine shop like Jim's spends much more time and better machining practices to achieve much closer tolerances than any OEM I've ever seen. Although bigger diesels that have replaceable sleeves are much closer than any gas engine. Especially cylinder to cylinder. But they usually make up and small differences by using different sleeves. And big diesels have individual heads.
@johnpopoff7950
@johnpopoff7950 Жыл бұрын
Cummins yes some did have one head per cylinder and the old Big Cam/Small Cam engines had one head per 2 cylinders. Detroit Diesel only one that I can think of had one head per cylinder, that was the 149 series. I know I built many Detroits, Cats and Cummins.
@joshy0369
@joshy0369 Жыл бұрын
Always awesomeness
@cobra02411
@cobra02411 Жыл бұрын
Been a while since I've seen a 396/402 block. I forgot they had the valve reliefs in them... Good stuff!
@johnpopoff7950
@johnpopoff7950 Жыл бұрын
427/454 don't need valve reliefs
@cobra02411
@cobra02411 Жыл бұрын
@@johnpopoff7950 Yup, bores are bigger.
@TxStang
@TxStang 11 ай бұрын
That deck finish is beautiful , I just my 5.0L back from the machine shop and the deck finish is rough ... they claimed it is fine and that it is normal and the MLS head gaskets will seal but I am having doubts ..... small town machine shop ...... wish we had good machine shops like you in our area !
@patrickwendling6759
@patrickwendling6759 7 ай бұрын
Thank you for your knowledge and video's USA 🇺🇸
@alanschwartz1157
@alanschwartz1157 Жыл бұрын
Dang! I love watching you work. The attention to detail is phenomenal. That engine will run better than Chevrolet could have imagined. So, you had to sleeve one side? I really wish I could have had your service on my last engine. King Balancing in Glendale, AZ did mine. They did a pretty good job. They're probably the oldest in the valley. I'm positive the customer is going to be ecstatic with your work.
@joe-pm3lb
@joe-pm3lb Жыл бұрын
wow u are a wizard with engines
@MrsSunshine75
@MrsSunshine75 Жыл бұрын
Not enough piston to wall clearance for that old school TRW style forged piston, it has me worried!
@timot7746
@timot7746 Жыл бұрын
Nice job, again.😀
@ronsanchez2842
@ronsanchez2842 Жыл бұрын
“That’s why the surface finish looks the way it does.” Oh you mean 10x better than anything I’ve ever machined lol
@BubbaAyers1969
@BubbaAyers1969 Жыл бұрын
Nice 👍 Thanks for a great video
@mrenfilade7178
@mrenfilade7178 Жыл бұрын
Good for us youre back to work after the honeymoon! Congratulations and +1 Like
@JAMSIONLINE
@JAMSIONLINE Жыл бұрын
Thank you!
@lilmike2710
@lilmike2710 Жыл бұрын
I have a low mile 454 out of a wrecked 86 model RV that has a date with the machine shop really soon. Its a high deck big block so we're gonna see what we can do about all that 😁 and it honestly doesn't need bored but imma go .030 O just because of..... Reasons and stuff 😊 Love the channel
@FlatBroke612
@FlatBroke612 Жыл бұрын
I’m 99% certain GM did not produce a 10.2” deck 454. The 366 and 427 commercial engines were factory “tall deck”. You can turn the 427 into a ‘54 if you clearance the block for the rod bolts though.
@lilmike2710
@lilmike2710 Жыл бұрын
@@FlatBroke612 It's 9.800" You're correct 👍 I've never owned one before nor have I ever taken one to a machine shop. I was told in passing by someone that there were 2 different 454 blocks. One for street applications and one for service. And I just assumed the one in my old rv would have the tall deck. 😁 For once I'm happy to have been mistaken. I still have the engine but I can't decide what I want to do with it 🤔 Do I go with a C10 build or cram it into a car? Right now it ain't hurting a thing sitting there on the shop floor. 😊
@Klemeq
@Klemeq Жыл бұрын
Love the videos! Is there ever a follow-up for the engine after all the machine work you've put in? I mean, 'after we blueprinted the block they added XYZ heads, ABC cam, and this is the dyno result' etc. Just thought it would be a neat way to conclude a block's story.
@kramnull8962
@kramnull8962 Жыл бұрын
Then it starts to become a sales pitch like with SMR. Build a engine the entire time telling you how much better his $40,000 engine is than the one he is building. Then The one he is building goes up in smoke the first trip out. "The ole Should have bought my $40,000 engine"....
@jacquespoirier9071
@jacquespoirier9071 Жыл бұрын
much much better than most shops will do
@Aleks_Mechanics
@Aleks_Mechanics Жыл бұрын
Notification Squad!🔥🔥🔥 HAPPY NEW YEAR!🎉🎉🎉🎉🎉
@nwliving
@nwliving Жыл бұрын
4 measurements needed. 1. Align bore crank 2. Parallel bore crank and camshaft 3. Perpendicular bore cylinders to crank bore. 4. Then parallel decks to crank. Very common misalignments of all v blocks.
@timothylines631
@timothylines631 11 ай бұрын
rocken star . love it.
@grantreid8583
@grantreid8583 Жыл бұрын
All the v8 boring jigs i have used didn't clamp through the cam tunnels the clamping studs continued up and then a flat bar went right across the top of the inlet manifold sealing faces. Also if you want some fun with your workmates get some of the boring chips some battery acid and mix it together in a glass. I used to do this and crankgrinding etc from age 15 to age 34 when i realised i had to get a job that paid a decent wage and i didn't go home everynight stinking of various oils, cleaners etc. The only thing i miss is being able to build my own engines dirt cheap and help the occasional mate out. I am in Aus and the job took me overseas for a few years so i have many memories of it still as i near retirement.
@midniter2001
@midniter2001 Жыл бұрын
I love watching the videos guys. I have a question, can you bore and hone fiber reinforced material engine? For example a Honda h22 engine has fiber reinforced material sleeves. And generally aren't bored or honed by most.
@thatguywillt
@thatguywillt Жыл бұрын
I really like that block height gauge. I use a 12" caliper, but that seems much more efficient.
@FishinFool70
@FishinFool70 Жыл бұрын
I have one for sale.. Old comp cams
@stevenbelue5496
@stevenbelue5496 Жыл бұрын
Are you talking about the deck height gauge that measures from the main saddle? Where does one purchase those?
@davidlagle7000
@davidlagle7000 11 ай бұрын
Very smart puppy
@lecnac855
@lecnac855 Жыл бұрын
Excellent.
@stevenconstantine2747
@stevenconstantine2747 Жыл бұрын
Great work! Btw, who makes the deck height gauge?
@rokkebill
@rokkebill Жыл бұрын
Nice video ! What is your max cutting depth with that cbn cutter ? Also what cutting speed and depth do you get the best result with ?
@garygroves9999
@garygroves9999 Жыл бұрын
Have you ever had a need to line bore any blocks? I see you setting the machine up on the crank journals wondering if that is ever a concern? (probably not on this particularly block)
@bobbiggs6959
@bobbiggs6959 11 ай бұрын
I'm a new subscriber, and let me first say, I love your videos! I'm learning quite a bit. I do have a question though. It seems when you bore and then hone a block, it seems that you start on the middle cylinders and then move outwards. If this is true, what is the reason for doing so?
@bigal878
@bigal878 Жыл бұрын
Great job 👍🏻🇦🇺
@Bird_McBride
@Bird_McBride 6 ай бұрын
Wisco in Quebec will manufacture any piston you want. Just send them the specs and the blueprint. They'll machine or forge your pistons to your desired specs. This is how to get around obsolete pistons.
@91rss
@91rss Жыл бұрын
my cousin heard that some old farm equipment tat used GM big Blocks used the HP stamped blocks. and 3 tons had LT1 cranks in them. ever hear anything on that?
@ronwade2206
@ronwade2206 11 ай бұрын
Worked on about a dozen, 1963 GM 390cid Cadillac motors, my best old friend has had every model 1963 Cadillac. Not one engine block was decked square or decked equally from side to side, Line Boring these things can be down right silly!
@patrickwendling6759
@patrickwendling6759 Жыл бұрын
Awesome 👌🏻
@raysimon1368
@raysimon1368 11 ай бұрын
Nice looking machine job what grit is your final hone and what would the surface finish measure at would love to operate some of your machines boring decking and installing hardened seats but my favorite would be the serdi for valve jobs love the inserts where you get all your angles in one plunge or one at a time whole lot better than the old stones that I play with nice video
@ronflood5697
@ronflood5697 Жыл бұрын
is the pan rail really the best way to reference? I prefer to use the main and cam centerline, after machining/correcting both of those datum lines first, of course. On your CV-616, you should try the C30 series stones instead of those AHU/JHU Stones. Those short stones were designed to straighter out tapered cylinders, not as much to finish hone fresh bores.
@rogermason5833
@rogermason5833 Жыл бұрын
Question: since this block has cyl sleeves installed, do you have to be concerned about the cyl sleeve thickness you are left with after final boring and honing? If so, what is an acceptable limit on the cyl sleeve thickness?
@crazylarryjr
@crazylarryjr Жыл бұрын
Question, Wouldn't you want to bore with at least the main caps torqued down and possibly a torque plate on the top of the block? I would think you'd want all stresses induced while boring to keep the bores round when properly torqued down
@shenanigansofmannanan
@shenanigansofmannanan Жыл бұрын
Is there an issue with thoroughly documenting the numbers and re-stamping the numbers after surfacing? My understanding is that the "numbers matching" is the verifiable claim of "all original" that is so coveted. To that point, I'm of the opinion that it would be better to have an original block/head set that had been properly refreshed/rebuilt/ machined over the years than to replace it simply because the numbers would be gone. Ftor: I grew up as an old school diesel mechanic's kid and had the privilege of spending time around skilled craftsman in mechanic/machine/fabrication shops. I've always appreciated the discipline and attention to detail that is required for you trade. Thank you for sharing with us
@richardhintonracing
@richardhintonracing Жыл бұрын
Lovely quality work - move to England !!
@JAMSIONLINE
@JAMSIONLINE Жыл бұрын
You fund it and I’ll move! Lol
@richardhintonracing
@richardhintonracing Жыл бұрын
@@JAMSIONLINE Only wish I could - machine shops here in UK have become as rare as hens teeth everything has been bulldozed and had houses built on it workplaces , pubs, factories, filling stations, theatres, cinemas, dealerships, hospitals . UK now one vast housing estate .
@nickimperialengines2559
@nickimperialengines2559 Жыл бұрын
What do you do for (say) 400 SBC where the bore comes right down into the main web?. I bore on a large mill so i can shift the block once the cutter is through the bore so the cutter cuts the web a few thou for a further 1/2 inch to clear for the stones. I am looking at getting a boring machine as I have the work for it but am unsure if I'd be able to do this on a Rottler etc
@davidwickboldt712
@davidwickboldt712 Жыл бұрын
Why not use the specs from the main thrust location for bore center on each bank? Then hold factory center to center? I'm just thinking it would line up on the crank better than sweeping in each sleeve.
@Unhandleablehandle
@Unhandleablehandle Жыл бұрын
Does decking after boring ever have an effect on the chamfer size on the bores?
@grayv3
@grayv3 Жыл бұрын
If you deck the block after cutting the valve relief and chamfering the bore edge doesn’t that mean you’ll have to cut the relief deeper to be the correct depth and you’ve removed the chamfer?
Why Did The $500 Allis Chalmers 210 Engine Seize?
29:58
Jim's Automotive Machine Shop, Inc.
Рет қаралды 462 М.
This Kubota Was Nearly TRASHED By A DROPPED Valve Seat!
25:56
Jim's Automotive Machine Shop, Inc.
Рет қаралды 275 М.
1❤️#thankyou #shorts
00:21
あみか部
Рет қаралды 88 МЛН
Is it Cake or Fake ? 🍰
00:53
A4
Рет қаралды 20 МЛН
Wait for the last one! 👀
00:28
Josh Horton
Рет қаралды 104 МЛН
The day of the sea 🌊 🤣❤️ #demariki
00:22
Demariki
Рет қаралды 83 МЛН
The Customer BROKE A Main Stud Off In Their BRAND NEW LS Block...
13:09
Jim's Automotive Machine Shop, Inc.
Рет қаралды 219 М.
Why Balance A Stock 396 Big Block Chevy?
14:50
Jim's Automotive Machine Shop, Inc.
Рет қаралды 203 М.
Installing Two Repair Sleeves In A 258 AMC Straight Six Block @JAMSIONLINE
17:27
Jim's Automotive Machine Shop, Inc.
Рет қаралды 215 М.
Cylinder Offset Changes Everything
23:45
driving 4 answers
Рет қаралды 2,5 МЛН
I made a precision gearbox - with NO GEARS.
30:09
Not An Engineer
Рет қаралды 1,3 МЛН
The First Head Had Seen Better Days... Ford Tractor 172ci Gasoline Cylinder Head Valve Job
16:38
Jim's Automotive Machine Shop, Inc.
Рет қаралды 287 М.
Making a BOLT ACTION Pen || INHERITANCE MACHINING
17:58
Inheritance Machining
Рет қаралды 2,9 МЛН
This Cummins Crankshaft Was Almost Scrap Metal...
51:37
Jim's Automotive Machine Shop, Inc.
Рет қаралды 1 МЛН
This 225 Buick DAUNTLESS V6 Odd Fire Was WORSE Than We Thought...
35:22
Jim's Automotive Machine Shop, Inc.
Рет қаралды 198 М.
Incredible Wheel Restoration Process 🚙
1:00
Handmade Heroes
Рет қаралды 10 МЛН
#automobile #experiment #smartphone
0:15
Kashvi Giggling Fiesta "KGF"
Рет қаралды 20 МЛН
Front Tractor Tire Project #project
0:51
SB Skill
Рет қаралды 13 МЛН