This is a great video. Simply described and very easy to follow. Learned a lot as a novice pool owner. Thank you!
@gsmith68304 ай бұрын
Thanks Craig. You were right. One of my connectors has a short. Was able to get the board powered up with just the filter pump connected. Tomorrow I will figure out which actuator or relay is bad.
@SanjayMehta-k8w Жыл бұрын
Excellent video and clear explanation. Very helpful!!
@ryanbedwell21442 жыл бұрын
Thanks mate, really helpful video. Installing my first valve actuators next week :)
@craigwooster66462 жыл бұрын
Good luck! Glad it helped.
@TheCONDREA Жыл бұрын
Would be good to have it on written form !!
@ertertertttttt11 ай бұрын
Well done - Thank you!
@NICOSHORETEES6 ай бұрын
VERY INFORMATIVE! THANK YOU
@jehumelchor2 ай бұрын
Thank you for such great video, if I may ask a question, one of the pool actuator wires got peeled by rubbing to the zip tie that was holding it. Could I just repair the wire or do I need to replace the whole thing.
@TheCheckthisout79 күн бұрын
Repair
@eduardoarie2514 Жыл бұрын
Congratulations wonderful video and very well creating very didactic, congratulations
@robertpenczar89303 жыл бұрын
I like it a lot nice video I am having problem with my customers pool and spa valves their Ortega 3 port vales. I have replaced all the the inserts but when I go to put the bypass on or spillway and then in the morning it's drained down to the water level it's a raised Spa I'm thinking about cutting Ortega valves out and putting in the Jandy 3 port valves I think the inside housing of the Ortega Valves maybe wart 1971 I believe.
@michaelberman47492 жыл бұрын
you must be int he Carolinas with Charlotte Pipe PVC 🙂 Thanks for the videos
@MrVictorkin Жыл бұрын
Simply amazing 🎉
@JohnQPublic345 Жыл бұрын
Im trying to assign a new JVA that will rotate when turning on the gas heater loop. Any ideas how to assign the actuator on this control board? I have two terminals remaining: the tried and fourth terminals
@nazaretnaz8712Ай бұрын
Hello, I need your help, I change my board and now when I put in spa one of my valve not turn and my spa drain all water, I check both valve is working but board doesn’t send signal to turn valve
@dsmbreed2 ай бұрын
I want my intake and return valves to shutdown in the spa mode direction (not pool mode as your video shows) because of the elevation difference I have between my pool, spa and pumps. How can I accomplish this? with my AquaLink RS system?
@craigwooster66462 ай бұрын
Thank you for your comment, we are currently working on a video for this exact question. It should be posted within the next few days.
@dsmbreed2 ай бұрын
Looking forward to seeing this!
@craigwooster66462 ай бұрын
There is no correct way to do this. There is a problem in the way your pool/spa valves are configured or one or more of your valve bodies has falied and/or you are missing check valves or you have a check vavle/s that has failed. I can help you out, however it is somewhat complex and I will need to see how your pool plumbing is configured and what is happening. You can call the office, give your information and I'll try to help you out
@Joe_Public Жыл бұрын
What if your wiring is too long. It looks like a birds nest from the installer and looped around the pipes. Can you shorten them?
@dennisskinner23393 жыл бұрын
How or where do i get a replacement door latch?
@SatyaPDatta2 жыл бұрын
Good afternoon sir we’re located my box have no power
@robertpenczar89303 жыл бұрын
Haven't heard from you what are your thoughts on my first comment
@ncasagrande15 ай бұрын
i have the same system, i had to factory reset it. how do i actually program the actuators to do something when a button is pressed? i have a pool with spa spill over and water features. 3 actuators total. suction, spa and water feature
@mikefitzpatrick435 ай бұрын
What kind of automated clock do you have? Do you have an automated controller? If you do you hafe to set the times for everything to run. And inside your automated time clock you hafe to run the wire to the correct auxiliary
@ncasagrande15 ай бұрын
@@mikefitzpatrick43 i have an rs 6 controller. the panel is in the house, the box with the relays and wiring is out by the pump
@psarabi Жыл бұрын
sorta worthless post - this is for plug and play use only, does not cover adding additional actuators for custom applications and programming them for something like a evap chiller etc..