Jeep JK Driveshaft CV Joint Replacement

  Рет қаралды 11,177

Cliff's How To Channel

Cliff's How To Channel

Жыл бұрын

In this video, I replace the CV joint on the front driveshaft, out of my 2014 Jeep Wrangler JK Unlimited.
Below are the the links for the parts/tools in the video:
TeraFlex 1744014 Factory Replacement Kit (JK Rzeppa CV)
amzn.to/3Ka2QQs
ABN CV Joint Ear Clamp Banding Tool
amzn.to/3TK0pXO

Пікірлер: 29
@CR3W1SH03S
@CR3W1SH03S Ай бұрын
Bast practice is to grease from one side only until the grease comes out the other side. This way, you know that there isn't any trapped air in the bearings.
@adamcarpenter5190
@adamcarpenter5190 Жыл бұрын
Teraflex actually recommends cleaning the bolt holes free of grease so it doesn't counteract any of the threadlock on the bolts, excellent video though!
@jeans2679
@jeans2679 Ай бұрын
I've just changed mine. i had to tap mine into the spline too but you have to be very carefull and make sure they line up. if you look into the joint spline recieving area there is a tiny section where they are no spline grooves (boot side) So even its seated on the spline it may not be 'lined' up, get in with a torch and line it up properly before you start pushing it through!
@CliffsHowTo
@CliffsHowTo Ай бұрын
Yeah, you’ve got to be careful for sure!
@ezcooper8754
@ezcooper8754 6 ай бұрын
Place tape over the bolt holes before greasing to eliminate/minimize the grease going into the bolt holes
@CliffsHowTo
@CliffsHowTo 6 ай бұрын
That may work! The tape may not stick though. Worth a shot!
@DobeyChru
@DobeyChru 9 ай бұрын
Thank you Cliff.
@cleivamiam2376
@cleivamiam2376 Ай бұрын
I couldn't be farther from being an expert in this but I think what doesn't go in the bearings you're supposed to put in the boot and end cup. Pretty sure you were good the first time.
@Rowdyrigs69
@Rowdyrigs69 Жыл бұрын
I recently did this on my Jeep and 80ft-lbs seemed like a lot for those little hex screws. I looked it up in the service manual and 80 ft lb is for the flange side bolts. The side that goes to the front diff. The CV joint bolts are only 24 ft-lbs. Maybe that's a screw-up on Teraflexs instructions side of it but I thought I should throw that out there.
@CliffsHowTo
@CliffsHowTo Жыл бұрын
True
@adamcarpenter5190
@adamcarpenter5190 Жыл бұрын
Hello friend, I believe you have those numbers backwards :) he states in the video that the hex screws are 18 ft-lbs (though the onscreen text says 15, at 21:48) and the actual bolts on the other side are 81 ft-lbs. This is also what TeraFlex has in there instructions (15 ft-lbs for the hex screws and 81 for the axle side bolts) also seen here - kzbin.info/www/bejne/nanakJyFbt-oiK8 at 8:32 and 9:03
@cleivamiam2376
@cleivamiam2376 Ай бұрын
I'll never understand why people that have never done something before make video tutorials. This one seems pretty benign but I've seen several that make a job much more difficult than it should be.
@CliffsHowTo
@CliffsHowTo Ай бұрын
It shows people that even if they’ve never done a particular job before, that they can in fact do if. It’s motivation, and inspiration. It also helps people gauge the difficulty. In all honesty, most of my videos are my first time doing a particular job. But I have a lot of experience doing a wide range of tasks. Just look at my channel at the number of videos I’ve uploaded.
@panfilofrias331
@panfilofrias331 4 ай бұрын
Hola amigo soy de México dónde lo podré comprar ese mismo para Jeep liberty 2008
@shropshirelado1849
@shropshirelado1849 Жыл бұрын
90% of this video is just this chap putting grease on the joint😂
@CliffsHowTo
@CliffsHowTo Жыл бұрын
True! I used to skip past parts like turning the wrench in my videos, but people complained that I wasn’t “showing what I was doing”. So now I include all the steps. Even the ones I think are not important.
@scoobastowlifechronicles4075
@scoobastowlifechronicles4075 9 ай бұрын
Hey Cliff, did you ever have a popping noise when you accelerate it from a dead stop before you replaced at CV joint? My 2015 jeep wrangler is doing that from time to time not consistently every time though
@CliffsHowTo
@CliffsHowTo 9 ай бұрын
Before and after. I’ve had that since buying the Jeep 2 years ago. For me it’s more of a thump than a pop though. I haven’t been able to figure that one out yet!
@scoobastowlifechronicles4075
@scoobastowlifechronicles4075 9 ай бұрын
@@CliffsHowTo mine is thump pop combo lol It doesn’t do it all the time
@scoobastowlifechronicles4075
@scoobastowlifechronicles4075 9 ай бұрын
@@CliffsHowTo has it got any worse or any better in 2 years?
@scoobastowlifechronicles4075
@scoobastowlifechronicles4075 9 ай бұрын
@@CliffsHowTo kzbin.info/www/bejne/oIPSeodpead0g6Msi=Gy1RCrTzvIZGFqhh
@roofrat68
@roofrat68 9 ай бұрын
Having that same problem. What size of socket did you use to sit it?
@CliffsHowTo
@CliffsHowTo 9 ай бұрын
I honestly don’t remember. Sorry. I just grabbed one!
@cody.meadows
@cody.meadows 9 ай бұрын
32mm
@chrisvalentine9735
@chrisvalentine9735 Жыл бұрын
What would be some of the symptoms of this needing to be replaced?
@CliffsHowTo
@CliffsHowTo Жыл бұрын
For me, the boot got a tear in it, and all the grease flew all over the underside of the Jeep. But the joint can also wear out. If you’re getting wiggling or play in the joint, then it’s worn out.
@chrisvalentine9735
@chrisvalentine9735 Жыл бұрын
@@CliffsHowTo thanks
@annmariepinkerton3345
@annmariepinkerton3345 11 ай бұрын
We diagnosed it when we went into 4H and had a rattling noise…like a playing card in the spokes of your bike. A friend told us to go under and try to wiggle the joint. If it moves, we needed a new one. It moved and here we are 😂
@cleivamiam2376
@cleivamiam2376 Ай бұрын
Omg dude, it doesn't all go in bearings. The rest goes in the boot and cap. Lol
HOW TO - Fit a Plastic Cover Dimmer Switch - AU
4:20
busterandpunch
Рет қаралды 750
Playing hide and seek with my dog 🐶
00:25
Zach King
Рет қаралды 35 МЛН
Mama vs Son vs Daddy 😭🤣
00:13
DADDYSON SHOW
Рет қаралды 46 МЛН
WORLD'S SHORTEST WOMAN
00:58
Stokes Twins
Рет қаралды 104 МЛН
TeraFlex Install: JK Rzeppa High-Angle Factory Replacement CV Joint
9:31
TeraFlex Suspensions
Рет қаралды 110 М.
Damascus Steel From Milling Chips!
15:47
Alec Steele
Рет қаралды 1,2 МЛН
Jeep JK Front Shaft Rebuild - 5150 Motorsports
35:05
5150 Motorsports
Рет қаралды 1,3 М.
How To Restoration Drive Shaft & CV Joint Inner End Outer Boots Change
11:44
How to Choose Your Axle Gear Ratio
19:15
BleepinJeep
Рет қаралды 1,6 МЛН
Replacing Driveshaft Rzeppa Joint Jeep Wrangler JK
15:33
Donny The Late Model Tech
Рет қаралды 27 М.
САКЕНДІ ҚАТЫНЫ ҚЫЗҒАНЫП ҚАЛДЫ
0:31
Ән - көңілдің ажары.
Рет қаралды 208 М.
Gym lover..#trollface #short #shortsfeed
0:21
DS SIPUN OFFICIAL
Рет қаралды 6 МЛН
😳 Это ПРЕВРАЩАЕТ всё в ПИЦЦУ !
0:28
Настя, это где?
Рет қаралды 5 МЛН
Сделала Сюрприз Брату После 3 лет Разлуки ❤️
0:26
Глеб Рандалайнен
Рет қаралды 2,1 МЛН
She realized that true happiness was not near this guy 😇🦄❤️‍🔥
0:12
iPolina Queen of the Cringe 👑
Рет қаралды 71 МЛН