Advance Adapters does a bench install of their 50-7906 New Process 231J Slip Yoke Eliminator Kit.
Пікірлер: 63
@chuckstubblefield59984 жыл бұрын
Once rtv is applied both pieces need to be put together right away ( rtv instructions) then finger tight bolts until rtv is slightly squeezing out. Let set 1 hr, then torque to spec. Following rtv instructions really works 100%. God bless and enjoy.
@ninja636394 жыл бұрын
I like how the video shows removing all the other snap rings except that heavy duty one. That thing was a pain in the butt to get off the original shaft and 10 times worse to get on the new shaft
@fiveninegarage3 жыл бұрын
For real
@captainobvious6334 Жыл бұрын
That is the whole reason I watched this video Maybe advance adaptors has a little tip… NOPE
@ernestmyname Жыл бұрын
What you need is "horseshoe ring pliers" proto's part # is 250G. You can find these pliers also by searching for "special lock ring pliers". They have knurled surfaces to spread the eyeless lock rings.
@181suydam5 жыл бұрын
Just found this video, excellent! Well laid out and explained! Great job!
@JavierOllllO11 жыл бұрын
Great vid... Turn the speedo sensor to another position and while transfer case turns freely ajust it also make sure sensor seated well ..u can feel the senson tick when engaged
@greerengineering12 жыл бұрын
What kind of lock ring pliers are being used at 5:50 in the video? I'm having a hard time finding anything local that opens large enough.
@pietrolorenzetti40639 жыл бұрын
great video! concise, precise, clear ... !!!
@Mitchumthegreat12 жыл бұрын
awesome, I finally find the official AA video, great job, planning on doing my install today and this helped a lot. might want to put jeep in the title though, it was difficult to find this
@milkmanpeter6 жыл бұрын
You said to leave the cover off for an hour to cure .i would put cover on so it stick but don't tighten until cure
@AdvanceAdapters197112 жыл бұрын
Yes, the large spring is on the rail and gets compressed when the rear of the case is bolt back on. However there is one other one that also comes to mind. We can email you a picture if you need it. send us a PM for email info since posting it to the video comments is prohibited.
@robertdoran738711 ай бұрын
Had a shop do my SYE. Drove 467 miles in one month and now it is stuck in 4 Hi. Tried driving slowly forwards and backwards while shifting into 2 Hi with no change. Disconnected the linkage and tried shifting the transfer case manually. No change, still in 4 Hi. Question: If the snap ring holding the gear in place on the shaft is not correctly installed, will the gear move out of position and cause the transfer case to be stuck in 4 Hi? The linkage is not the problem.
@Mitchumthegreat12 жыл бұрын
install went great! very superior product
@g-man163710 жыл бұрын
Excellent, Thanks for sharing.
@josephfarley79832 жыл бұрын
Is there a video you can recommend that’ll show you how to press the bearing out so I can fit it on the shaft? I have the old style 231..
@schmitice Жыл бұрын
Where do you buy the star seal, no one at the auto parts knows what I’m talking about? I’m also having bearing noise from the cage bearing, chanted the fluid, just keeps squawking at low speeds, goes swat after driving it for awhile… also if the transfer case is in nuetral I try spinning that rear yoke, I have to spin it and it doesn’t spin freely, like the bearings are shot
@longhorn84594 жыл бұрын
Is there a reason you left the oil pump off when you first put the case back together? Why not leave them connected so you don’t have to use that little pick to attach the two?
@hailstrmofbroknglass12 жыл бұрын
When I opened up my case there was one spring sitting at the bottom of the case and one was on the shift rod. I'm assuming that the second spring probably fell off the rear of the shift rod when I was disassembling. Correct me if I'm wrong please.
@Grater81211 жыл бұрын
Very good video! Some time i planning to do this for my YJ!
@pissedoffpapa28417 жыл бұрын
Great video, thanx, Thumbs up on it, but next time please kill the music.
@IDSKoT11 жыл бұрын
Is this the same process for a '91 NP231J?
@reameri23410 жыл бұрын
4wheel drive high or low position
@jasonbox13326 жыл бұрын
what happens if u remove the two snap rings and the tail housing don't come off
@AdvanceAdapters197111 жыл бұрын
Did your installation require the step of pressing out the needle bearing cages? If so the lubrication system on those shafts are different than the style that we build. This will not effect the performance or have any adverse effects on the lubrication properties of your transfer case.
@abdielraal12 жыл бұрын
Best video I've ever seen..
@josephfarley79832 жыл бұрын
Will red or clear RTV work the same?? That’s all I have on hand..
@ironhorseoffroad29406 жыл бұрын
What happens if the slide hub thing gets installed backwards?Mine keeps popping out of 4 low and I’ve checked everything
@craigsturman66612 жыл бұрын
Yeay, WAY too clean! But very informative. Thank You!
@rafalica52533 жыл бұрын
Super program
@Shaunmnaude11 жыл бұрын
hi i installed my kit today and i have a concern with the new shaft i fitted all seems fine for now after driving it today .. but the old shaft had a oil feed hole to supply oil to the gears that where swaped over and the new shaft does not have a oil feed hole for this point it has other hole where the planitary splines are if anyone could let me knoe if this is normal of if i am gioing to soon have a permenat 4wd due to gear running dry on shaft and sezing ?? thanks
@michaelschweigert625711 жыл бұрын
so would this be the process of making a 231amc (21 spline) become a 231j (23 spline) to work with a AX-15 ?
@memerx2412 жыл бұрын
great vid
@jasonoconnell35574 жыл бұрын
Where can you get that bench top yoke holder???
@outkazt2711 жыл бұрын
What about NP 242 transfer case? Do u know where I could get a kit for it?
@1969ramstein12 жыл бұрын
thank you
@Shaunmnaude11 жыл бұрын
No mine had no needle roller bearings in have a 2005 tj wrangler
@bassaxist6 жыл бұрын
On the off chance. I am installing Advance Adaptors SYE arrives from Rusty's tomorrow. Started disassembly however my snap ring pliers are (expensive) shite! What brand is being used here? can be seen at 01:30. They look decent. Are they? Thanks
@ernestmyname Жыл бұрын
I had the same problem. For anyone wondering, what you need is "horseshoe ring pliers" proto's part # is 250G. You can find these pliers also by searching for "special lock ring pliers". They have knurled surfaces to spread the eyeless lock rings. You can do it without them but it's a real pain.
@NK-dl2nc7 жыл бұрын
Great ! really enjoyed it. Next time put a different video to the music as watching somebody fixing shit really put me off my air guitar !
@dougb61832 жыл бұрын
Thank for the video!! Next time no music..can't hear you talk..
@Foof5010 жыл бұрын
Ok I am trying to remove the front yoke but it keeps moving on me. I put it in 4W low prior to removing the case. What am I doing wrong?
@downnoutdubin9 жыл бұрын
Foof50 I used a 3lb sledge hammer head to stop the yoke from spinning against the transfer case casing. However something wood would be the better option as it's softer than the aluminum casing.
@Shaunmnaude11 жыл бұрын
What do u mean by pins ?
@erikcaldwell29132 жыл бұрын
Is that 4 wheel drive high or low its supposed to be in??????🤔
@michaelwhitehead44462 жыл бұрын
Hello I just installed one of these and cycled through all positions to make sure the shift rod was short enough. The shift rod would hit the new tail housing and bind if it's too long.
@scgeek1213 жыл бұрын
great video thanks!
@firebreathinggarage21174 жыл бұрын
Needed more ads and RTV.
@bodyart334411 жыл бұрын
look for a set that doesn't go to pins on the ends
@angelus50129 жыл бұрын
That piece that has to be no more than an inch mine seems to be an inch and a half. how to I shorten it?
@downnoutdubin9 жыл бұрын
Michael Padgett If you have a dremel or die grinder I'd use that. Angle grinder would work too.
@mattydoinks9 жыл бұрын
Michael Padgett a hacksaw lol
@CurrySoSpicy8 жыл бұрын
Angle grinder with a cutting wheel
@Johndoe-dp2gi8 жыл бұрын
What is with the music????? I do not get it???
@shea883010 ай бұрын
Much easier to just disassemble the oil pump and realign and stick the tube in. It’s how they did it at the factory and trying to do it with a little stick is some nonsense
@gregmeola90127 жыл бұрын
a fucking wood chisel???
@jaygreene7130 Жыл бұрын
Horrible, distracting, LOUD music. Ugh. Makes video virtually unwatchable.
@jaygreene7130 Жыл бұрын
Good Lord. I have to mute the video. UNWATCHABLE with music playing.
@itsCopello5 жыл бұрын
Here is how it comes apart after we took it apart. Garbage.
@chicago16807 жыл бұрын
The theme with these how to videos is they must put crappy music for no reason whatsoever.