How To Install Bathroom Sink Drain/Faucet, No Leaks Under Gasket, Threads [SOLVED] 2023

Your host Jeff Ostroff shows you the correct way to install a bathroom sink drain and faucet without getting that annoying leak underneath the bathroom sink, with water dripping down the threaded drain pipe and out the black rubber gasket. This bathroom sink drain leaking underneath affects a lot of people who otherwise installed their bathroom drain according to the drain manufacturer's instructions. You'll avoid bathroom sink drain leaking threads forever.
From Home Depot & Amazon (paid affiliate links)
🛒 Glacier Bay Mandouri 8" widespread LED Faucet in this video: amzn.to/2Efy2vY​
🛒 Lower price 4" center set faucet: amzn.to/2PCcJa8​
🛒 Oatey Fastape 1/2 in. Thread Sealing PTFE Plumber's Tape: homedepot.sjv.io/WDDKdn
🛒 Ridgid Z Change Faucet Tool Wrench: homedepot.sjv.io/NKKP4N
🛒 RIDGID One Stop Wrench Kit 27023 from Amazon: amzn.to/2ClCbNa
🛒 RIDGID One Stop Wrench from Home Depot: homedepot.sjv.io/9XEjQ
🛒 GE Advanced Silicone 2 Clear Kitchen and Bath:
homedepot.sjv.io/Ry6Dr2
Table of Contents (Click to jump to any chapter)
0:00 Introduction of bathroom sink leaking underneath gasket problem
0:34 Anatomy of Threaded Drain Pipe, Causes of Leaks
2:30 Solution to Problem Installing Sink Drain with No Leaks
4:30 Wrapping Plumber's Teflon Tape Around Bathroom Drain Threads
6:50 Installing Drain Flange and Threaded Drain Pipe
10:08 Installing Bathroom Sink Faucet
11:20 Installing Bathroom Faucet Stopper, Lift Rod Assembly
12:15 Removing Bathroom Sink Aerator, Flushing Faucet
12:35 Water Testing Bathroom Faucet, Drain For Leaks
13:15 Checking Downward Slop of P-Trap Arm Into Waste Pipe
13:35 More Leak Testing Hot Water, Overflow, Overnight Drips
14:45 Discussion: Plumber's Putty Not Recommended On Drain Gasket
📺 WATCH: How To Install Kitchen Faucets: DIY Plumbing Tips: • How To Install Kitchen...
📺 WATCH: How To Fix Bathroom Sink Drain Leaks Underneath Gasket, Threads [SOLVED]: • How To Fix Bathroom Si...
📺 WATCH: Why is my Kitchen Sink P-Trap Leaking at Connection Nut?: • Why is my Kitchen Sink...
📺 WATCH: How to Replace A Kitchen Sink Drain Strainer, Repair Leak: • How to Replace A Kitch...
📺 WATCH: How To Fix Leaking Shut Off Valve FAST DIY - Avoid Plumber: • How To Fix Leaking Shu...
📺 WATCH: 4 Plumbing Parts/Tools You Should NEVER Use. • 4 Plumbing Parts/Tools... ​
📺 WATCH: How To Repair/Replace Leaking P-Trap Pipe Under Bathroom Sink: • How To Fix Bathroom Si... ​
📺 WATCH: How to Install P Trap Under Bathroom Sink, Drain Pipe Off Center: • P-Trap Installation Dr...
Note: Some links we provide are affiliate links which if you click on them and buy tools, we may receive a small affiliate commission. We appreciate you supporting our efforts to bring you world class tool reviews, remodeling and repair videos, and shop with me videos looking for the best discount tool deals.
✅ SUBSCRIBE:
✅ For more DIY remodeling tips, tricks, engineering disasters subscribe here: bit.ly/2vj06cB
Should your leaking drain repair use plumber's putty to avoid staining the bathroom vanity sink. We'll also cover Teflon tape (plumber's tape), pipe dope sealant, and silicone to fix the bathroom sink drain.
The lower Teflon tape for the black bathroom drain gasket should be wrapped counter clockwise, to match direction of the drain gasket screwing upward from underneath the leaking sink basin. The upper Teflon tape should wrap clockwise around threads of the leaking drain pipe to match the direction of the drain flange inside the sink, screwing downward onto the pipe threads in a clockwise motion.
You still have to fill up the sink basin with water until it starts to drain out through the overflow hole, then you also need to let the water suddenly all drain out. You have been moving a lot of parts underneath your bathroom vanity sink, so make sure to test for the sink trap leaking as well. If the sink trap is leaking, we add pipe thread sealant to the leaking trap connection.
Causes of your bathroom sink drain leaking underneath
If the drain hole in the sink has imperfections preventing the gasket from mating to the sink for a perfect seal. Some people have issues installing Moen faucet systems with Moen drains and they have a leak. Drain leaks happen with Glacier Bay as well, the leaking vanity drain is allowing water to leak down the threads of the drain pipe under the vanity sink. It is one root cause of your bathroom sink leaking from the drain gasket.
The drain repair solution for this vanity sink leaking issue is to wrap plumber's tape around the top of the pipe threads where the drain flange will screw on. Wrap tape on pipe threads where rubber drain gasket mates to the bottom of the basin underneath the vanity.

[@jeffostroff]

From Home Depot & Amazon (paid affiliate links) 🛒 Glacier Bay Mandouri 8" widespread LED Faucet in this video: amzn.to/2Efy2vY​ 🛒 Lower price 4" center set faucet: amzn.to/2PCcJa8​ 🛒 Oatey Fastape 1/2 in. Thread Sealing PTFE Plumber's Tape: homedepot.sjv.io/WDDKdn 🛒 Ridgid Z Change Faucet Tool Wrench: homedepot.sjv.io/NKKP4N 🛒 RIDGID One Stop Wrench Kit 27023 from Amazon: amzn.to/2ClCbNa 🛒 RIDGID One Stop Wrench from Home Depot: homedepot.sjv.io/9XEjQ

[@c7adventures376]

I was about to question as im watching. My new faucet had a note saying not yo use anything on the threads. I was surprised and still going to do it to be safe. But i guess i will trust them and leave the bare. 👍🤠

[@darrellvartanian3361]

. Mlm. Mlm.... ,.

[@christinaong5250]

What brand of silicone caulk are you using? So many not sure which is right..

[@footlongburrito]

Those "arrogant plumbers" say things because you continue to give wrong info after saying that they commented you don't know what you're talking about, most putty doesn't stain, or Crack anymore, for years matter in fact, and second, use brass pop up assemblies, they are much better

[@jeffostroff]

@@footlongburrito If what you said is correct, why do they sell a stainless putty on the same all right next to the regular putty?

[@floydrturbo1]

What a very thorough explanation and so professionally presented with no annoying background music. To the point with great video. A++

[@jeffostroff]

Thanks so much?

[@lorivezina7913]

NO music -YES!!!

[@simonpeter6]

there's like one guitar lick at 6:42

[@shannonobrien9922]

Agreed!!!

[@tracyburigana7576]

Thank you ! Great presentation !

[@klugj01]

I think this is the BEST DIY video on ANY topic that I've ever watched. Organized presentation, so detailed yet well-expressed and easy to follow and understand. You should have a professor's emeritus chair! Just great

[@kimpeats9712]

After fighting my sink for 2 days, I am so thankful to have found you! Thank you for saving me from calling a plumber!

[@nemo227]

I was putting in a replacement vanity and sink this evening and couldn't FIND my plumber's putty so I put it on my shopping list for tomorrow. WHEW! Close call. My new drain is black plastic and now I've changed my list to include clear silicone to seal the drain. I already have the teflon tape. It's always nice to view a video in which we can actually learn something USEFUL THANK YOU, JEFF!

[@jeffostroff]

You bet Nemo, glad to help!

[@lonletson9025]

I just want to say thank you for the way you broke everything down and explained it all to me. You made fixing the drain on my sink so simple. Thank you so much.

[@jeffostroff]

Awesome Lon glad to see it worked for you.

[@androidery1999]

I completely agree! Crystal clear and very informative.

[@spikeklein270]

Agreed. Jeff tells you why he's doing what he's doing. He doesn't skip over anything, or assume we know something. Very helpful.

[@michelleflammia8148]

I have to say, Jeff has once again saved my day & saved me definitely LOTS of money!! He's incredibly thorough & goes nice & slow therefore I don't have to keep rewinding his video! I've learned SO from you Jeff! I tell everyone about your awesome videos! KUDOS TO YOU & MUCH GRATITUDE AS ALWAYS! 🎉💪🏻👏🏻👍🏻

[@bobcroon8943]

Some people just have the gift of teaching.

[@k333rl]

reminds me of seejanedrill. so calm and soft spoken while hitting every small detail to make sure that everyone has a total understanding of not only what is happening but also why. about to do my first faucet and drain replacement ever on a 50 year old sink. wish me luck.

[@bdbmarine]

After many times attempting to stop the leaks, I watch this video. It took me longer to view the video than it did to correct my problems. Thank you.

[@emeraldforest]

Best plumbing repair video I ever saw.

[@jeffostroff]

Thanks, I'm glad you liked it!

[@jonabila3329]

Hell yeah!

[@entropysfo]

Thank you, Jeff! I had water leaking on the floor everywhere. I went and searched and found your video. 30 minutes later I had a no-leak faucet and drain fully installed. Really appreciate your time to help others with this problem.

[@jeffostroff]

Glad it helped!

[@MG-eu2oz]

These demos are perfect for anyone, especially a DIY-newbie. Thanks so much for answering so many questions I had, and addressing the confusing advice out there on simple things...like when and when not to use plumber's putty. It helps so much!

[@jeffostroff]

Glad it was helpful!

[@Dadster171957]

Thank you Jeff, awesome video! I was tearing my hair out over this faucet and your mastery saved me after two failed attempts. Very well explained. So much appreciate you sharing your wealth of knowledge and expertise! 😅

[@tedeschliman]

Wow! I’ve watched a dozen videos on this. This one is miles above the others in simplicity and thoroughness. Great job!

[@jeffostroff]

Glad it was helpful!

[@MFC1029]

Jeff, you have put together one of the best tutorial videos on KZbin. You speak a language that everybody can understand and your delivery invites to keep watching and you help me fix the leak in my sink! Congratulations!

[@jeffostroff]

Wow, thanks!

[@alexvogtcolettefarlandvogt2306]

Great

[@Italian69Boi]

exactly 💯

[@juliaware7257]

This was so helpful! I’m in the middle of my first install and had leaks up at the gasket with no idea why it was happening. Super glad you mentioned to not use putty because everyone I asked said I needed it. This showed me a couple other mistakes I was making too. Great video!

[@jeffostroff]

Great to hear!

[@mik693]

Thank You so much for your detailed instructions, I’m replacing 2 of my bathroom faucets next week and stumbled upon your video , could not have been at a better time to find this , 👍 and subscribed , love your monotone

[@billnickerson253]

This was extremely helpful!! I found you for the exact reasons you mentioned, applied the teflon tape and works perfect, no leaks!! Thank you!!

[@jeffostroff]

Great news bill I'm glad it worked for you

[@jeffmather1585]

I'm experiencing no leaks with my drain replacement, thanks to your expert advice. It's much appreciated. 💯

[@jeffostroff]

Thanks so much for the SuperThanks!

[@sandir9835]

Thank you Thank you!!! You've so clearly explained how to fix the exact leak I had when I installed my new faucet!

[@dhow414]

Great stuff. Subscribed. Though I have done this before being a home owner I don’t do this often. Having a guide like this helps to refresh my memory to resolve issues if I missed something. It is amazing how much a homeowner can do on their own if they will simply make an effort and consult a knowledgeable source. Thank you for being that source today.

[@denisef1153]

Phenomenal presentation. No annoying music is always a plus. I now feel confident to do this job. I watched so many videos over the past two weeks but never felt confident like I do now. Thank You for the explanation on the plumbers putty on black rubber. I had it out to use. I will now go to Home Depot for the clear silicone. Best thing for me is that I bought the exact faucet to install. (Oh and I finally got brave enough to remove that yellow cap they put on for shipping ). I couldn’t turn the water off as the valves were frozen. I used WD40. Now I can turn them with ease. Nice and lubricated.

[@tnyvalenzuela]

Thanks Jeff, simple, direct, and comprehensive. In conclusion, excellent presentation.

[@ALPHAJACK78]

This is the best instruction I have ever seen! Thank you! I just did this exact thing today, smaller bathroom sink, less room. I wish I saw this before I attempted to remove the faucet retaining nuts underneath. I tried to use channel locks and regular pliers, no room to really grab and turn them. Finally got the RIDGID EZ Change Plumbing Wrench Faucet Installation and Removal Tool. What a Godsend! Also, the plumber that installed my sink, tightened them so much as if I lived in California and was expecting an earthquake of 9.0! No need for that! and he used putty everywhere, that cracked and fell inside the drain, further clogging it! Just got to let the silicone cure, the do the leak testing. Thank you so much again, new sub here for sure! Have a great day and a Merry Christmas, God Bless You🙏🙏👍👍

[@lisao9677]

Thank you for your video. I had a leaking bathing sink from a new install I did myself. This was my first attempt at plumbing. I watched your video and followed your instructions and it is now leak free. Thanks again!

[@edwardbain5391]

Yes you are right after my first two of those years ago I learned the hard way. After I put really good silicone on all the threads. Then seal the rubber gasket around the base of the sink with silicone. This is a real problem great to have your input!

[@jeffostroff]

Thanks for sharing!!

[@ryantrohon7042]

True professional right here. Love when someone passes on their knowledge so well. Thank you!

[@jeffostroff]

Glad you enjoyed it!

[@darinsmith9468]

Great video, Jeff--so glad I watched it. I've had troubles getting lavatories leak free in the past. After spending 2 days getting a 50-year-old 3-hole faucet and drain off of a cultured marble top, I'm ready to put in the new kit (which is now mostly plastic compared to the all-brass stuff I removed). This will help a lot. You are right about getting old stuff out being a beast. My 50-year-old kit was severely corroded by all that time exposed to hard water, time, and copious amounts of dried up plumber's putty used when it was installed. I had to cut the rusted faucet flange nuts to get the handles off & finally had to use my dremel to cut the drain flange seating nut, and the flange itself as nothing was breaking loose even with multiple tries of penetrating oil. Would have been faster to go to the dremel first. Fortunately, brass cuts easily with the metal-cutting discs (and a flex shaft made it so much easier).

[@jeffostroff]

Yes you have to go old school on these old school fixtures

[@orlandoespinosa2656]

You have explained and demonstrated exactly everything I needed to know. Huge help! Thank you!!🤙

[@user-zd9gv6nm5q]

98% worked for no leaks. No dripping at any of spots covered in vid. After the last leak check, did get slight drip on the lower tailpipe just below where it meets the t-joint for the ball rod port. Didn’t realize that screwed into the upper level. Based on your advice of a threaded components, took off the p-trap and added grey tape to the threads on the the lower tailpiece. Once it and p-trap were reinstalled did the leak checks. This time no leaks. Thanks for the vid. Haven’t had to replace a sink in ~35 years. Bought the Ridged tool and it was easier than the basin wrench.

[@heatherk.906]

You are an excellent teacher! Thank you for making this video with such care to instruct the rest of us.

[@jeffostroff]

You're very welcome!

[@emilysimmons9511]

This was so incredibly helpful and exactly what I needed! Thank you so so much!!

[@FaithisKey792]

Thank you sir. You just came up on my radar searches, I’m forever grateful. God bless you and your love ones.

[@bunbee2023]

This was extremely helpful...I just re-installed my brand new Moen bathroom faucet using your Teflon tape trick and no leaks!! 👍🏽👍🏽

[@jeffostroff]

Glad it helped Bun Bee

[@mikevukas9818]

I have this problem for years! Thank you for solving the mystery, worked like a charm on my latest installation.

[@jeffostroff]

Great to hear!

[@jean-sebastienlegare1718]

Thank you @jeffostroff. Very clear instructions, good audio and video. I stumbled on this video because I was getting water droplets pearling down between the "cone shaped" silicone gasket and the underside of the sink basin. I'm replacing the drain on an old bathroom sink. The edge of the hole against which the gasket comes into contact on the underside of the basin has eroded/chipped and is no longer perfectly round -- so the gasket (which is perfectly circular), can't seal the hole properly. I've disconnected my ptrap, and followed your instructions. I've teflon'd the thread where the gasket lines up, like is shown in the video, and finger-tightened that nut to get the gasket to seal as much as possible (without deforming it too much) against the basin. Then I used channel lock pliers to give the nut an extra quarter turn. Where I went slightly off the beaten path of your video, is that I added a bead of silicone all around between the gasket and the underside of the basin (after cleaning and drying the surfaces). I'm hoping that will do it. My initial idea was to craft a custom seal with putty on top of the silicone gasket, but I'm glad you mentioned that putty shouldn't be used against rubber/silicone. It should take care of the irregularities in the shape of the basin's hole. I'll wait for the silicone bead to cure, and test again to see if it's water tight. I might have to repair the sink's basin hole if this doesn't do it (I can't change the sink!) Perhaps also something you could talk about in another video: My new drain shipped with a rubber gasket which sandwiches between the drain hole ring (where water enters) and the sink. That's in addition to the rubber cone-shaped gasket underneath the sink. I initially installed the drain with the top gasket which came with the drain, but it made the sink ring protrude by about a millimeter from the bottom of the sink -- so there's always a little pool of water around the drain hole after emptying the sink. After watching your video, I ditched that gasket and used plumber's putty to make that seal. (there are no plastic parts in my case, just stainless steel (drain), and enamel (sink) ). Thanks!

[@jeffostroff]

Man I cannot Stan those stupid gaskets that they give you it's such a dumb idea to put a gasket under the bottom of the flange up on top of the sink just for that very reason like you show it because it makes it stick up off of the bottom of the sink and collect water there to me the best solution is always to just use silicone to seal the flange down to the down to the basin. let us know how your repair worked out because I'm a little leery every time I hear about ships on the bottom of the basin that might mean that the basin is now disqualified from ever working properly .

[@scottarcher7]

First time doing plumbing work and installed 3 new bathroom faucets today following this video. 3/3 with no leaks, thanks for the help!

[@monicaspates3019]

The is a must see video. Every detail of the installation explains how to do it and how to fix what you did wrong! So glad to watch this. ⭐️ ⭐️ ⭐️ ⭐️ ⭐️

[@etjason1]

Wanted to say Thank You. Followed your instructions using tape and no leaks. The sink and faucet manufactors stated not to use putty because of the plastics. Used GE Advanced silicone in small tube. Also been using the 2 tool kits from Rigid, makes things a pleasure. You got a new subscriber.

[@jeffostroff]

Glad it helped Jason, welcome aboard!

[@kevincameron1163]

Wow this was great. Thank you. I just had this problem and I fixed the leak with plumbers putty. I was just diy trying to figure it out. It has worked so far but I probably need to go back and use silicone and Teflon tape instead of plumbers putty. Thanks very much for this video. Very helpful

[@jeffostroff]

You're welcome!

[@EVOComputersnet]

Thanks, Very Thorough! I felt confident in doing this replacement after years of construction, handyman projects, etc. But this video was a great at covering the potential problem areas and reminded me to use my teflon tape, testing it with the hot water for expansion, etc. keep up the good work.

[@michelecrone8186]

Great video, Instruction on how to tape below the sink flange is very helpful, I re-used the existing fixture and sealed with putty. No more leak.

[@diegocelaya7302]

What a master! This is how you install a sink! Not as quick n easy as most people think. But if you do it this way, it will WORK. Which is the most important thing. Thank you for this Jeff. I watched your previous video on this topic (how to keep the overflow inlets in the drain from leaking) and it helped me very much. This video is even better: so calm, confident, and thorough. Haha. Sorry for all the praise but I just remember how much of a bear it was in the days before I knew how to do it right trying to get it to stop leaking.... Great work!

[@jeffostroff]

Thanks diego!

[@kickassclone75]

Get a sink to stop leaking ? Wtf world do you live in ? I’ve never had a sink leak and I’ve never used Teflon tape like this . Yell me wtf the Teflon tape is doing to prevent leaking in this scenario? The cheap stack he’s using is why he has leaks maybe buy quality part one piece stacks that don’t screw to the flange to begin with and you won’t have leaks.

[@DataWaveTaGo]

@@kickassclone75 RE: " buy quality part one piece stacks that don’t screw to the flange to begin with and you won’t have leaks." I did that. Still leaked. Used tape & sealant to get a leak-free installation. You should do a video to show how you get yours to work every time. Would be worth a lot for anyone doing this type of installation.

[@henryburt72]

Thank you so much. I am a "do-it-yourselfer" and tackle just about everything myself. But . . . I have replaced many of these over the years and always dread it, I know I am going to have to fight a leak! Have been fooling with my most recent one for 3 days and 2 drain kits. I applied the tape as you suggested and no leak. It's like magic - can't wait to replace another one - JK. Thanks again.

[@jeffostroff]

Glad it was helpful! No leaks this time!

[@TXCannoli]

Thank you for this! Just fixed my bathroom sink following your video and NO LEAKS! Not a plumber and wouldn’t even consider myself a handyman, but gave myself a POB (pat on the back). Thank you for sharing this. The teflon tape was the big deal. The person who owned the house before just smothered the drain pipe with plumber’s putty, but the teflon tape seems to work. And the whole job looks clean and professional! Thanks again!

[@jeffostroff]

Yes you can always tell the person who doe snot know, because plumber putty should never be used on threads.

[@kellybederin6686]

SO helpful! Was just about to use plumber's putty and you saved me!

[@Noahsoak]

This video is awesome! Thank you for all the detail! Doing all this today.

[@jeffostroff]

Glad it was helpful Melissa!

[@agostinodibella9939]

I liked the detailed explanation on preventing leaks.

[@jeffostroff]

Glad to help Agostino!

[@tim6151]

Thank you. That was a great video, which taught me some things no one has ever taught me before. I appreciate it!

[@SergioRodriguez-je2sh]

One of the best videos ever I’ve seen in you tube , very well explanatory. Thanks for all those hints .

[@sylviagm]

First time I see one of your videos, I like how you explain everything so I subscribed! Looking forward for more DIY!

[@jeffostroff]

thanks Sylvia!

[@yperry1]

Yours was one of several videos I watched in preparation of my first plumbing adventure. Super helpful; presentation. Replaced my cabinet, p-trap and faucet, in the bathroom. Took me all day, but great personal satisfaction. Thanks for your videos!

[@jeffostroff]

Glad it was helpful! and congrats on doing it yourself Yvonne!

[@everettwhite9874]

I just ran across your videos today and you answered every question I had because the information covered exactly the problem with the p-trap and the misaligned waste drain. My project worked great. Excellent and throughly explained presentation. 🥂

[@jeffostroff]

Awesome, Everett, glad to help

[@pdavis4853]

Subscribed and rang the bell!!!! Jeff you are overkill with the details of your repair. I LOVE that about you!!! You enabled me to make a much improved install. Thanks buddy!

[@patmat.]

I learned something important ! Never realized that the leak would come from the threads... but these are not watertight threads like Gas or NPT, makes sense. Thank you

[@jeffostroff]

You bet Pat, ad Thanks for watching

[@Lockemeister]

Now this is the video that I wanted to see! Done by a careful plumber that has a relaxed but scientific approach. A+++ Liked and Subbed

[@jeffostroff]

Glad it was helpful!

[@robertmcaree7016]

Where did say Jeff is a plumber???

[@robertmcaree7016]

@@jeffostroff Are you actually a plumber Jeff???

[@heiditiredmommyartist4423]

Great tips & input on safety checks! I’m glad I saw this before installing my faucets!!!

[@venerican3736]

My friend, you are a true professional! Thank you for the provided detailed guidance!

[@benfranklin4524]

I was having an issue with the seal of the pivot on a ordinary chromed brass Delta drain... at least that was what I thought it was. Turns out it was the threaded joint just below the pivot. Following your advice with Teflon tape fixed it. Thanks!

[@jeffostroff]

Glad I could help

[@leonardneil7494]

Good work thanks

[@patricksimone8845]

Thank you for this very useful information, especially the teflon tape on the drain threads. I have an additional problem and that is how to aline the trap directly below the sink drain hole. The replacement sink hole is a half inch farther from the wall than the original sink. Thank you.

[@jeffostroff]

We have a video that covers this: kzbin.info/www/bejne/mJCyhJqtpdmYiJY

[@denniswahl1607]

Thanks Jeff for this helpful and timely video. I was having the same kind of leaks after installing a new drain in my bathroom sink. Now I know how to fix it. I'll look for your videos next time I'm doing a DYI repair job around the house.

[@rogerbrown7075]

This site definitely showed me how to STOP a leak on the new replacement drain in my bathroom sink. Now I can redo the installation and add the teflon tape above and below the drain holes on the new drain. 😊

[@anwalt693]

Excellent video. Clear explanations, clear and helpful views of the product(s) and source of the problem. We are all lucky to have you help us.

[@briankinnaman6532]

Thank you so much for sharing this! I’m replacing our bathroom sink faucet and drain for the first time and your video helped out a great deal. Cheers!

[@jeffostroff]

Glad to help out Brian

[@grny28]

I've used that tool for years....it's a must especially for DIYers.

[@jeffostroff]

Yes that tool is one of my favs, I also have a an older metal version but this newer one is more versatile due to the removable parts and different nuts it can mate up to

[@tellsthetruth894]

Hi Jeff, thank you for the EXCELLENT VIDEO. Learned a lot from it. I would like to ask you a plumbing question please. We have an old single story house in a great shape, built on a slab in 1976. We have two bathrooms, about 22 feet physically apart, that are almost identical in design. The front, entrance side, of the bathtub is about 3 ft from the commode. The discharge from the commode is about 8 feet from the main sewer line in the yard. The tub drain discharge is about 14 feet from main sewer line in the yard. The bathrooms are in great shape, but the kids bathtub (only) releases sewer fumes when taking a shower. But it doesn't happen every time they use the shower. Also I noticed that if the commode is NOT flushed before taking a shower, they do not smell the abnoxious odor. I am thinking it may have something to do with the vent system between the tub and the commode, for that particular bathroom. But if so, how do I fix this problem considering a concrete slab and very nice walls. Thank you for your response.

[@michael.imv.8989]

Omg ive been looking for this

[@jeffostroff]

Glad you found it Michael!

[@ljones98391]

That orange Ridgid faucet tool saved me getting off decades old rusted parts up inside a very small vanity. I love it.

[@dorkultra]

I really appreciate you spending the time to explain all about the tape and the direction to apply it. Great instructions, going to tackle this project now

[@jeffostroff]

Thanks for watching!

[@anthonyh2884]

Great stuff friend 👌🏽😬

[@jeffostroff]

Thank you! Cheers!

[@dauntiekay2768]

I am gonna have to get that Ridgid Z Change Faucet Tool Wrench that has to be a handy tool especially if you have rentals. As always--a great informative video!

[@jeffostroff]

Good call!

[@bullpup33]

It's worth it.

[@Jhairoh405]

Just bought mine and yes it's amazing

[@erikg88]

Omg. Thank you! Thank you! THANK YOU!!!!! I FOLLOWED everything you did and there is no leak coming from the bottom of my bathroom sink counter! You're a life saver!

[@jeffostroff]

Yeah man! That's the way it's done!

[@indarramoutar2506]

Great video with lots of best tips to avoid issues when installing plastic fittings including Teflon tape and silicone.What a great learning experience for a DIY project.

[@jeffostroff]

Glad it was helpful!

[@davekaye1924]

Another good test for leaks is to close the drain, fill up the sink with water, and then open the drain. This will force a large volume of water down the drain. I discovered one of my leaks this way.

[@jeffostroff]

Yes, we do this as part of the overflow test shown at 14:09

[@otisbigsby]

It’s called a hydrostatic test.

[@frankbuck4564]

I followed all the instructions that came with my facet, reinstalled it twice and it still leaked. Then I saw this video, followed the advice it gave and no more leaking. Why don't they just put this in the directions? Thanks so much

[@jeffostroff]

Lol I always wondered that the same thing, but if they put it in the instructions there sort of admitting that their threads aren't very good at meeting up two other components

[@ojibwayinca8487]

Hey, I just wanted to thank you. This is exactly what I needed. I certainly appreciate the time you took to make this video.

[@jeffostroff]

You're very welcome!

[@raulgamez5602]

Just ran to this problem yesterday and was about to KZbin. Oddly notification came up about your video. How did you know 🤔

[@jeffostroff]

Greta minds think alike!

[@jeveuxpasdechainecal]

It always happens to me. I think our smartphones are listening to us. And I am not joking. 😐

[@peterboissiere9684]

Pipe dope on the bottom of the pop up is all that's needed

[@jeffostroff]

Yes, some people do that too, but you have to be careful, many pipe dope bottles tell you not to use on black ABS plastic pipes, so tread carefully there.

[@hondapilot]

Wonderful explanation. I have 5 drains to fix. Just saw this video

[@dieselthumbs82]

Thank you for the tip about wrapping the drain assembly with tape even if the directions don’t mention it. I had a leak that I couldn’t figure out and this definitely helped me resolve it. Great video.

[@beerbeforebreakfast]

Use generous amount of pipe thread sealant on the entire drain threads and you will be good to go and much simpler.

[@robertp7209]

Do both😁

[@robertmcaree7016]

Believe it or not too much tape can split fittings, 4-5 wraps is sufficient in most if not all applications!

[@robertmcaree7016]

I do not recommend beer before breakfast!!!

[@beerbeforebreakfast]

🤣 I call myself beer before breakfast for 2 reasons. 1.I usually don't eat until dinner so when I get home at 530pm my first calories are beer. 2.It has a nice ring to it! Thanks for the reply

[@doneown503]

Dammit, wish I saw this yesterday! Oh, well! Wasn't leaking today, see what's up tomorrow .

[@jeffostroff]

At least you'll know for the future!

[@danooe1790]

hahahah me too, only spot I forgot the tape and i think i snugged that nut up so much all the putty came out

[@valoriec]

I'm so glad I found this video. I JUST installed a sink/vanity combo an hour ago, and the drain leaked exactly like yours. I have the exact model of drain assembly too. Many thanks, and Merry Christmas!

[@jeffostroff]

Glad I could help!

[@robtphoto]

Third times the charm. I made two attempts to do exactly what you explained in the video with my bathroom sink drain. Then I was so lucky to see your video and the explanation about the teflon tape. I almost gave up and spent $$$ on a plumber...so THANK YOU!!!

[@jeffostroff]

Excellent! Nice work Rob!

[@pattiekeith2501]

Thank you. I am a 74 yr. old lady and my husband was paralyzed 3yrs. ago, he can walk around now but can't do plumbing. We live in S. E. Arizona and no building codes. I have hired people to do things and they just botch it up. So, I am doing it. My kids used to call me handy-mom. How can I tell if the pipes inside the wall are cpvc or pvc? This is because they have patched it so many times with little pieces. Can I put pex onto the existing pvc/ cpvc? The valves are frozen. No shutoff to the house. I will have to shut the well off for that. I am scared that if I run into a problem, we will be out of water until I can get help. Any tricks you might have to loosen the frozen shutoff valves or video would be greatly appreciated. I will try the wrench blaster tomorrow . Your video is great because you go so nice and slow and show the parts. You also speak so clearly. Most of the videos are too fast and if they say the name of something, a word I am not familiar with, then I am lost. You, sir are wonderful for producing these videos. Thank you again.

[@jeffostroff]

the CPVC pipes are yellow/crème colored used for water supply in the house. The better pipes are copper or PEX, with PVC Sch40 pipes which are white, used for draining only. I am hoping you don't have CPVC because it is costly and devastating, and connections crack too easily, and if you have it, don't let handymen work on it. You'll have to bite the bullet and hire a master plumber with experience working on CPVC. Also you might have to re-pipe the house which many people end up doing with CPVC, and they can switch to PEX at that time. As for your stuck valves, are you talking about under sinks, and are they attached to copper pipes? Let me know what you have so I can direct you to the proper video which we have.

[@pattiekeith2501]

Thanks for answering I think it is all pvc in my house. No building codes here. The shutoffs are under kitchen and bathroom sinks. Right now I am just trying to stop the leaks. I don't see any yellowish pipe. I used WD40 and wrapped with a hot rag ,it took about 3 days until it finally loosened. Would liquid wrench be ok ? I don't want to destroy the plastic pipes. The valves are metal.

[@nordicpandi]

@@pattiekeith2501 I do the same, and have to learn a lot because handymen around here are almost impossible to get to show up, or they do whatever they feel like and usually it's done wrong and leaking. What color is the plastic pipes? Before you shut off the well I'd recommend filling gallon jugs of water for drinking and flushing the toilet and such so that you have water if something goes wrong.

[@yjxu66]

Silicone is good to prevent leak. How do you prevent mold growth under the Silicone? It seems it's impossible not to have mold with Silicone although the tube say mold resistant.

[@jeffostroff]

Mold does not like silicone and some newer types of silicone have properties that prevent mold growth

[@butterybeats]

Thank you for making this video! I watched it before and during the installation of my bathroom faucet. A lot of great tips and information.

[@jeffostroff]

Glad it was helpful!

[@Tom_Wade]

This fixed the leak on my brand new faucet install. Thank you 👍🏻

[@darrenadams9782]

The flange ultimately does not need any kind of sealing.

[@jeffostroff]

don't know where you got that nonsense from, you must seal the flange either with silicone or with plumber's putty

[@darrenadams9782]

@@jeffostroff ok! sealing the flange stops water from going where? water that goes past the flange ends up in the same area that over flow water goes

[@John60s70s]

I think sealing is needed if you want to fill and keep water in the sink for a while like soaking clothes etc. That can be convenient at times.

[@-Enrico]

I use plumbers putty & and pipe dope instead of tephlon tape no silicone

[@jeffostroff]

Yes, some people you have to be careful with pipe dope, many pipe dope bottles tell you not to use on black ABS plastic pipes, so tread carefully there.

[@jackwilson5479]

thank you for an excellent educational video. I work at Home Depot in the plumbing department. I have used this video content to educate people on how to install their own drain system. I have had good feedback to give these directions to my customers.

[@kathyr.6825]

Subscribed! Wow what a detailed explanation!! I’m excited I’ll be able to finish my new faucet installation myself now! Woohoo!! Thank you 🙏

[@peterboissiere9684]

I saw a drop of water on the paper towel

[@jeffostroff]

Yes, I put it there to show you what to look for

[@billmartin694]

Ive been a plumber for 23 years. I would recommend ditching the plastic to metal because some of these plastic parts are so crappy they strip the threads as your tightening them and always use thread sealer with t2 teflon not tape. Teflon top and bottom of beveled washer and threads where he used tape. No issues, period

[@jeffostroff]

Yes sometimes, people can only afford the cheaper plastic threads. As long as you don't overtighten, should be OK. I do need to to another video showing the sealer alternative, as some plastic thread companies say not to use Teflon tape because it makes you overtighten.

[@buzoff4642]

Just had a headbanging with Moen over exactly that, as faucet installation instructions say two-part metal pipes, but what was in the box was 1 part plastic pipe. The one plastic pipe presumes a moveable/removable p-trap pipe, which is not the case for the multitudes of older homes. They know it's not what they put in the box, I've no idea why their online (and in the box) instructions are for the two piece metal piping - it's deceptive for buyers who need the two part. Eventually Moen sent the two part metal pipe to replace the 1 piece plastic.

[@Lidrien]

@@jeffostroff I just installed a new stainless steel drain in my bathroom sink and it’s already starting rusting around the outside of the ring, where the sink bottom meets the steel drain ring. What did I do wrong? There are no leaks anywhere. I’m guessing it’s because I didn’t put silicone under the ring ?

[@williamrobinson5525]

Great info. I could of used this info about 4 hours ago. Had the same issue. I finally got it to seal up.

[@travisd3001]

Great video, well paced with clear shots of important bits. Just want to add that my moen faucet mentions that the drain stopper can be captured (called anti vandalism option) or used with the pin next to the stopper hole so that it can be easily removed for cleaning.

[@catchingdreams600]

That plastic drain is going to break, that's big box store trash; next time use brass.

[@jeffostroff]

I have never seen one break, the plastic is stronger than you think. However I have seen metal p-traps get all rusty and corroded and you can't unscrew the nuts.

[@grzesiop58]

@@jeffostroff use 100% brass. No plastic from box store.

[@icedevil2003]

@@jeffostroff Wholeheartedly agree with you. Good plumbing advice from a KZbin video? I didn't think it possible until now.

[@WApnj]

Completely ignorant... No thread sealer is needed at the top at all.. And teflon tape is for tapered joints not straight threads. Plumbers silicone grease is used on the bottom threads where the rubber washer sits..... That's where the water follows the threads out the bottom and leaks.

[@jeffostroff]

LOL another uninformed hater troll. Holy cow you are so unbelievably ignorant you absolutely do need a sealer at the top whether it be plumbers’ putty on a standard metal flange, or silicone on a plastic flange. Your knowledge of Teflon tape is completely wrong! LOL! Teflon tape is recommended on all threaded fittings just look at any shower head that you buy and then they always tell you to apply Teflon tape in the instructions from the manufacturer who I am sure knows way more than you do. Also you have no clue about plumbers silicone grease it is NOT a sealer, it is a lubricant that has maybe some minor sealing properties but you can't rely on it to be a sealer. I use silicone grease on compression valve threads to aid in tightening the threads more easily. The only thing you got right in your entire statement was that water flows out the bottom and leaks from the threads. And as ignorant as you are you obviously have no clue that we have used this Teflon tape on the pipe threads many times to stop this drip so we are obviously correct and obviously not ignorant.

[@mikefalcone6532]

Well explained and easy to understand and straight to the point. Thank you , seriously!!!

[@ccnixon]

This is a far better explanation than comes on the packaging. I was so unsure of how to properly do it right until I watched the video. A video is worth 10,000 written directions.

[@jeffostroff]

Most instructions stink that is why I make these videos

[@bobrub]

What a joke ..... a "not a plumber" trying to teach plumbing.

[@jeffostroff]

What a joke, a hater troll who knows nothing trying to make the audience think he knows something. We have solved this problem many times in the past.

[@karlfreddy]

Thanks! I have installed quite a few drain pieces that leaked mysteriously and never thought about Teflon tape. I have used some plastic pipe thread compound but your solution is so much more permanent.

[@jeffostroff]

Glad I could help! And thanks for the donation!