As for the roll cage don’t just cut it out and remove it but instead make them removable with pins so you keep the structural integrity but still ease of removing for work/maintenance
@joelan93mtfworkshop894 жыл бұрын
great videos! i would of pre lubed/ oiled the bores before winding it over.... dry bores.. no good, wear very quick
@11joesph14 жыл бұрын
Looks like you re getting better at editing. Great job josh! Keep working hard bro!
@JetSkiBrothers4 жыл бұрын
Joey Young thanks bud 😁👌👍
@captslick55574 жыл бұрын
you may be getting low compression because of the dry head gasket ...there is this stuff called copper coat spray you can get at any speed shop .. you just spray it on the old metal head gasket and it seals it much better
@jasonsparshott72083 жыл бұрын
The compression will come up put a couple of drops of pre mix down in each cylinder and crank it then and blocking off the intake will lower your cranking compression. The motor will run and compression will come up
@danschweiger13432 жыл бұрын
Nothing like the smell of 2 stroke in the morning
@jamescarroll52284 жыл бұрын
the cylinders are dry that's why it has low compression. put a little trans fluid in there then due a compression test.
@ryankyser52434 жыл бұрын
What James said. Dry cylinders. Rings can’t seal dry.
@jethroY81004 жыл бұрын
Id like to see a video of how to tune the 1100 i have one i completely rebuilt and i know they are prone to eat pistons so i want to make sure it has the best chance to live for a long time
@scottborst54304 жыл бұрын
If you take the X out of your robe bar you might encounter the boat bending and warping maybe remove it but make it where you can bolted it back
@joelan93mtfworkshop894 жыл бұрын
cant beat the smell of a 2stroke 😂
@jasonsparshott72083 жыл бұрын
Especially when it’s Klotz premix !!
@mickotoole47954 жыл бұрын
Im back micks sticks 🤣😎😎 that looks like a very clean three cylinder ....🤔🤔🤔whot did i miss🇨🇮🇺🇲🇺🇲🇺🇲♥️♥️♥️
@Javaster9184 жыл бұрын
That is awesome
@jasonsparshott72083 жыл бұрын
Great video though!!
@AboxofMonsters4 жыл бұрын
Weld and new head gasket and cross etch cylds. Your compression should be good now with fuel and running as it was. Lower comp., is normal on a dry stored motor. I would not use it with an old head gasket you will end up with a frozen engine after it sits. Just order one. Should be fine. Sounds fine now. I would have Twin bilge pumps you develop a leak you wont stay a head of it.
@jasonsparshott72083 жыл бұрын
You don’t have anyway to adjust your trim while in the boat under power ?
@Giant_Metal_Burrito4 жыл бұрын
Clapped. Out.
@nike12000haha3 жыл бұрын
Need a new 300 ace motor in that boat!!
@guycyr30624 жыл бұрын
Lets see more jet boat videos! If or when the kawasaki 1100 fails, maybe go gp1200?
@mickotoole47954 жыл бұрын
I love the intervil music jacub🤣🤣🤣🤣🤣♥️🇨🇮🇺🇲♥️🇨🇮♥️😎👌
@mickotoole47954 жыл бұрын
Ya need to rip that motor out and stick a hyabusa turbo in there josh i know you can du it buddy😀😀😀😃👌😎♥️🇨🇮🇨🇮🇺🇲♥️♥️♥️♥️♥️♥️♥️♥️♥️♥️♥️♥️♥️♥️
@brandonhanny27864 жыл бұрын
Oo maybe you could put the seadoo engine you took out of the gtx if you still have it. Just a idea :). Love your channel and stay safe.
@JetSkiBrothers4 жыл бұрын
Brandon Hanny thanks bud
@brandonhanny27864 жыл бұрын
@@JetSkiBrothers yea man. Any time. Your videos are awesome
@jasonskibrothers21924 жыл бұрын
When this thing goes, wow, it GOES!
@lylegrenoble20553 жыл бұрын
Ahh the smoke feels obnoxious on you're eyeballs when you're trying to see...
@tittan15004 жыл бұрын
Hope that engine had some lube in it when doing the comp test.
@mickotoole47954 жыл бұрын
Hi jacub its micks sticks im back 🤣🤣🤣😎♥️🇺🇲🇨🇮🇺🇲♥️
@handyallaround57764 жыл бұрын
you need to open the window, and get a good fan!, i love your guys videos, its been a while since i have watched them , sold my jetskis last winter , got another one kawi 4 stroke stx 15, runss good, but will probably get a few older kawi 1100s zxi,keep up the good work!, where can you get these little aluminum minis?,,,,,,,,,,,,,is jacob ''down with the sickness""?
@dukesoffortmohave82054 жыл бұрын
Y’all definitely need to get some more knowledge on 2 strokes 😂 that motor is gonna have air leaks for days
@jasonsparshott72083 жыл бұрын
I agree the only reason the first 750 let go was because it was lean ....
@xmotorx934 жыл бұрын
Josh inhaled the 2smoke 😆
@JetSkiBrothers4 жыл бұрын
xmotorx93 now I have 2 stroke fever 😂😂
@williamberck11524 жыл бұрын
CARB REBUILD ONLY . some jb weld on the crack. run it after that
@jasonsparshott72083 жыл бұрын
Check your compression now I’ll bet money the compression came up . If she didn’t have but 80,90,100 psi she wouldn’t have started that easily cold . It ran more like the carbs aren’t synced or it’s got some vacuum leaks cleaning carbs would have happened before the mtr went in
@bubba.watercraftj72694 жыл бұрын
How about putting that 1800 SVHO engine in it?
@mickotoole47954 жыл бұрын
Go josh go go🏁🏁🏁♥️🇺🇲🇨🇮🇺🇲♥️😎😎🤣🤣👌
@mattjonesturbo14 жыл бұрын
Cylinders looked pitted but hard to know the extent from the footage. Looks clapped out with a paint job.
@JetSkiBrothers4 жыл бұрын
Matt Jones it’s a garbage engine for sure
@azmartin19773 жыл бұрын
ultra150 engine would be the go 1200cc big boy
@jerryvair49194 жыл бұрын
Copper coat. Or mopar has MLS spray. Use all the time
@vacuumpowered61194 жыл бұрын
Its lighter then my 10 hp outboard engine xD
@JG-mu8jl4 жыл бұрын
Stick with the kawi engine
@HendoRising4 жыл бұрын
Be aware that cheap compression testers are not very accurate! The harbour freight ones are terrible as well as the cheap Amazon ones. They all read low. You need to get a real compression tester.
@HendoRising4 жыл бұрын
@ 24:40 in this recent TOT video: kzbin.info/www/bejne/aKWXp6GAdpl-r6s
@AboxofMonsters4 жыл бұрын
Hendric Vogel plus dry engine
@jeffbryner53554 жыл бұрын
The route u need to go is take the engine out of the 1200r lol go 4 stroke turbo
@JetSkiBrothers4 жыл бұрын
Jeff Bryner that would be a death machine
@jeffbryner53554 жыл бұрын
@@JetSkiBrothers yes but danm i bet it would be a blast. Flying through your track at like 70 lol
@sethdoane52954 жыл бұрын
I’ve had a couple different ones now and I’m going back to a 2 stroke the 4 strokes get a little heavy on a creek boat at times
@FORGETYOU84 жыл бұрын
Where's the x2 update
@JetSkiBrothers4 жыл бұрын
chooch it seemed like not too many people cared about the last x2 video. Which is not giving us much motivation for that project.
@FORGETYOU84 жыл бұрын
@@JetSkiBrothers man pls 🙏 I really wanted to see what kind of real life reviews it had im debating on getting one and putting a gp800 cc in it
@craigaustin47794 жыл бұрын
1200pv, or Kawi 310
@JetSkiBrothers4 жыл бұрын
Craig Austin a 310 would be completely nutty stupid fast 😂👍
@craigaustin47794 жыл бұрын
@@JetSkiBrothers Yep.
@LanceCriminal964 жыл бұрын
You two are goofy as hell lol
@scottwright3884 жыл бұрын
I would have to agree...I was thinking regenge of the nerds early on when I noticed the Star wars shirt.
@1AndreasKendu4 жыл бұрын
Get a fan 😂
@brianhanel74933 жыл бұрын
Goobers on the loose watch out for exploding battery
@Jacobskibros4 жыл бұрын
These guys don't know anything. Lame. My buick 455 would smoke twice as hard!
@JetSkiBrothers4 жыл бұрын
Jacob Superjet Jet SKI 😂😂😂
@Ajaxaxxess4 жыл бұрын
I have built 2 of these.. yo uneed to go find a river bro.. Lakes are boring
@danesworld4 жыл бұрын
Small turbo diesel. Yeah yeah
@kene68384 жыл бұрын
Jacob is a little cringe
@JetSkiBrothers4 жыл бұрын
Ken E should I tell him to be more boring in the next videos?