Worked great! Jim's tools work well, but they are pricey! The life of a flatrate mechanic, spend money to make money! Keep up the great videos!
@HarleyDavidsonWizard4 жыл бұрын
Thats the motto for sure!! Thanks for the compliment!!
@millionmilesman2 жыл бұрын
Good!!!
@alanmcclusky4 жыл бұрын
Impressive Jims tool my friend a must in any Toolbox regards Alan
@HarleyDavidsonWizard4 жыл бұрын
It's a good tool for sure!!
@richardedwin59803 жыл бұрын
Wizard, I should've clarified this...I was referring to the bushing for the shaft on the heel/toe shifter.
@lqqkout4thedude2 жыл бұрын
Great video. What was the reason for replacing the shifter sleeve? The video didn't give a reason for this repair/maintenance.
@HarleyDavidsonWizard Жыл бұрын
Removing the sleeve with this tool allows you to remove the gear shifter assembly with out dissembling the transmission. Usally your only in a situation like this when someone has tried to replace the shift shaft seal and put gouges in the gear shifter shaft or case and this tool makes the job super easy.
@eaglemachineworks14904 жыл бұрын
Thank you!
@HarleyDavidsonWizard4 жыл бұрын
👍
@davidross20344 жыл бұрын
Brad: What what the problem you found with the old shifter pawl at 6:17 minutes in the video?
@Bagrman-kt1ot4 жыл бұрын
U da man .. u do good work... 👍👍
@HarleyDavidsonWizard4 жыл бұрын
Thank you so much 😀
@dustinmontgomery9274 Жыл бұрын
I have a question. I allowed my shifter lever to run loose and stripped the splines. So I'm going to replace the shifter assembly. Do you think I could reuse the sleeve bushing? The new sleeves are unobtainable apparently
@HarleyDavidsonWizard Жыл бұрын
It's not common to replace the bushing in the case. I do it because I'm already in there. As alot of work to do the shifter assembly tho especially if you don't have the Jim's too to save you from pulling the transmission out.
@richardedwin59803 жыл бұрын
Wizard...what tool is used to remove the bushing for the shifter shaft? I know on 2016 and earlier the part number is 5518. But I can't find shit for the Milwaukee 8. Please help!!!!!!
@oleksasirotinin15329 ай бұрын
Could you please tell the difference with Jims Cruise Drive Shifter Shaft Sleeve Tool 1658?
@HarleyDavidsonWizard9 ай бұрын
Jims 5517 allows you to remove the shifter sleeve and then, therefore, the shifter paw from the transmission while the gearset is still inside the transmission. Where as the jims 1658 instructions mention that the gear set does for a fact need to be removed for the 1658 to be used.
@oleksasirotinin15329 ай бұрын
@@HarleyDavidsonWizard thank you!
@user-uv3zn3ib6d8 ай бұрын
Do you think this process can be done on an 06 FLHT 5 speed with Jims tool #1664? I sure don't want totake the trans apart.
@HarleyDavidsonWizard8 ай бұрын
I don't think so. I haven't seen a setup like this for 5 speeds.
@JeffinTD3 жыл бұрын
That is awesome! Thanks for sharing. What eras of transmissions does that work for?
@HarleyDavidsonWizard3 жыл бұрын
It's all 6 speeds.
@JeffinTD3 жыл бұрын
Good to know. Years ago a buddy had the lower (centering) spring break on a 5 speed...
@rodneywilson63963 жыл бұрын
Which 12045 Replacement oil seal is best? Some are Rubber, others have a metal outer ring with a rubber inner ring, and others are identified as double layered. How does an oil seal with a metal outer ring seal against the metal transmission housing/case?
@HarleyDavidsonWizard3 жыл бұрын
I use the OEM one. never had a problem with the before.
@jimmyvaughn84893 жыл бұрын
Will this same tool work on a 5 speed on a 92 heritage softail the spring actually broke
@HarleyDavidsonWizard3 жыл бұрын
No. It's a different setup on a 5 speed.
@jimmyvaughn84893 жыл бұрын
@@HarleyDavidsonWizard is there an easier way to do it other than pulling all the guts out of the trans to get to it
@HarleyDavidsonWizard3 жыл бұрын
no. not that i know of
@michaelwills78843 жыл бұрын
Any new vids?
@NealHartsChannel Жыл бұрын
Will this work on my 2006 Fat Boy?
@MrShintaokm2 жыл бұрын
Do you have the part number for the adjusting screw?
@Mr416cat Жыл бұрын
Why won't this tool work on a 5 speed
@HarleyDavidsonWizard Жыл бұрын
I haven't tried it on a 5 speed. But I believe it's because of the angle of how the shifter paw pass over the gears and stuff to be able to be driven out of the transmission.
@geoffozevans45004 жыл бұрын
Hi Brad , I watched one of your videos on how to take the free play out of the heel/ toe shifter, I thought I'd saved it but can't find it in your lists, can you direct me to the relevant vlog please, many thanks 😊
@HarleyDavidsonWizard4 жыл бұрын
Ive looked but cant remember which one it is. Lol
@geoffozevans45004 жыл бұрын
@@HarleyDavidsonWizard its OK Brad I found it 👍👍👍
@Brad__Gray3 жыл бұрын
I swear man it's annoying as hell how many pullers and different tool you have to buy in order to break down a harley. I'm doing a complete rebuild of my fxdx and I've probably ordered 8 different sets of specialty tools. If someone were to put together a full kit for like $400, they'd do very well. Lol