JJRC Q65

[@modelnutty6503]

yup, almost a 1:9 scale is pretty obvious, wish they didn't silk screen paint the hood! removing it without polishing/smoothing the plastic can be difficult, like my B-1 for all but the stars on the doors. cheap cheap drive gearbox: www.ebay.com/itm/Double-Shaft-Bevel-Angle-Gear-Motor-Suit-Worm-Reducer-3-6V-DIY-Parts-/272884694375?hash=item3f8931fd67 used thick aluminum flashing to enclose with stepped out mounting tabs, sealed up to hold a gob of grease. use the WPL 130 motor in it gives it some pretty strong grunt, the motor that comes with it is really worthless+weak. you can't slam from running speed to a stop, have to be nice decelerating, but it DOES hold it's spot climbing steep (physically it has no choice!). needs about 1/4" taken off shaft length, and 3 mm OD brass tubing sleeves to adapt up to the WPL U-joint shafts to JB-weld in place. for the price, worth messing with anyway, it's a little too tight to accept a 180 motor.

[@gabrielsilvaz4199]

model nutty I actually think the truck is closer to a 1:11 scale there’s no way my dudes would fit in a 1/10 scale very well

[@modelnutty6503]

yup, kinda tough call, the old Jeeps were pretty small. I'd about given up on the worm gear drive idea, until I popped a WPL 130 motor into it, really a nice surprise.

[@gabrielsilvaz4199]

model nutty Yeah the old Jeep like this are 80 inches and a half long wheelbase and the toys wheelbass is 7.6 making the truck 1:10.5921 scale

[@gabrielsilvaz4199]

model nutty yeah I seen them before as a kid we used to play with some like that worm gear. they look like they would work pretty good and they’re affordable

[@modelnutty6503]

no electronic brake needed is a pretty cool thing, but a hard drop from cruising to 0 on the throttle is pretty savage, like don't hand the transmitter to a child type savage lol.

[@gregpatterson2829]

i finally found a review involving action figure scaling. i can now make the purchase for my classified Joes

[@maproomgaming6886]

Same!

[@dannyevansrcenthusiastrhod7172]

Great work....Decent truck, I love the attention to detail you give all your stuff...Shows that your a true hobbyist...Bash on...🏁🚘📹🎥💺💻🏆🔊

[@ernsteliden6719]

I also love your attention to detail.

[@ernsteliden6719]

As a direct answer on a direct question. Yes, I do like your cutter, in fact i was just wondering if I should comment on it..😛 Love your review.👍

[@gabrielsilvaz4199]

Ernste Lidén Thanks 😋

[@RC1oNeTV]

I love this one!!! Really good!!!👍😁👍

[@ernsteliden6719]

I agree with you Gabriel about thr scale, or realy there is nothing to agree about, the numbers don't lie. 1/10.6-ish I Believe would be the correct scale😋 I have reason to belive that It will be less to scale after you finished with it. Keep up the gooood work 😉👍👍

[@roycheung7172]

kzbin.info/www/bejne/kKmcl4qkhqqhgsk

[@corwinwarren7621]

i subbed when i saw the knife on a string...never misplaced again

[@mobilmotornet1756]

Nice detail RC model

[@RogerWilco66]

I checked the measurements, the Jeep is perfectly 1:10. The 1:12 figures are way too small. I drove the real thing very often and can tell you that the jeep is a small vehicle. I barely could sit behind the steering wheel. I like that RC Jeep and with some mods it really looks great. One thing I will change is to move the front axle maybe 1cm up front and maybe lower it. It sits a bit too high.

[@rcsnapon2132]

Awesome jeep im thinking of buying one I also subscribed to you

[@johnnytube8231]

Awesome i will get one

[@paigesmith6416]

I've owned a couple of Willy's keeps they are really small to start with and the front leaf springs extend almost all the way to the front bumper I've taken mine up to hobby grade ..I replaced every thing but the frame rails..on the chassis with all metal components..I'm thinking of building a body out of aluminum coilstock ..I upgraded to a 7.4 lipo change the radio and the lights ..if you look at the front axel it's to far back and which takes away from all the detail ..

[@ww2rctanks738]

Im waiting for your upgrades on this gabriel. I reacon is gonna be really good

[@Thetreefella]

Nice jeep!!

[@LCMNUNES1962]

PERFECT JEEP RC , BRASIL OK.

[@herminigildojakosalem8664]

It seems that the frontwheel(s) are set a little far back.

[@the116army2]

Got one from BG for $44 bucks with canopy, looks great, runs bad, proportional steering is good but when I hold full left or right the motor slows to a crawl,Noticed a place for a speaker under the console .Sound module upgrade coming?

[@gabrielsilvaz4199]

The 1/16 Army Yep there is a sound module for this truck I have one coming

[@the116army2]

Found the problem with the bad run, gearbox from factory is defective ,gears bind causing the hesitation starting.

[@larrylooney4495]

I just ordered one got a question will the wpl meatal gears work in it

[@gabrielsilvaz4199]

larry Looney yep

[@gadlevy9205]

Very nice vid! Can you give me please details about the action figures that appear in time 10:20 ?

[@gabrielsilvaz4199]

Gad Levy Hi 👋 Thanks! go ahead and check out my channel! I have a couple of video talking about these action figures and accessories you can get more detail from those videos. They are 1:12 scale action figures the male action figure is made by Vortex toy and The female is a Figma action figure I customized all the details including her hair and facial features. Thanks for watching😉

[@joelstrummer6165]

Gabriel Silvaz what is the wheelbase of this RC?

[@gabrielsilvaz4199]

Joel Strummer 7.6”

[@gabrielpichardo1492]

That Walmart associate box cutter

[@jovzzrc835]

The gear and axel of this rc its same to wpl?

[@gabrielsilvaz4199]

owwss? hahaha! No the video I specifically say that they’re quite a bit beefier meaning bigger than WPL

[@bijusebastiansebastian3671]

Price

[@ungurdani8346]

Salut my friend super car super video subscribe subscribe 😎😎😎😎

[@jagrajsinghdodra]

What is price

[@gabrielsilvaz4199]

jagraj singh I’m not sure of the current price you’ll have to look at bang good or eBay To find out the price of the truck after modification it is considerably higher than stock form

[@jagrajsinghdodra]

@@gabrielsilvaz4199 right

[@bestamerica]

' nice pretty jeep... how come american company dont like to makeing their own R/C jeeps