JKS Sway Bar Quick Disconnects Jeep Gladiator Wrangler JT JL

Buy them here!
amzn.to/2R9enGJ

[@c130aviator]

Shout out to www.badattitudeoffroad.com for providing me the parts. Awesome shipping, awesome customer service.

[@tombaffa9374]

Good to hear from you again! Hope you and your family are doing well.

[@c130aviator]

Thank you sir. We are doing well, just tired of the lock downs and masks.

[@AlejandroSanchez-qo8qy]

Definitely helped me installing mine! Thanx for uploading 👍

[@randycarter4529]

Good stuff! Good to see you back.

[@c130aviator]

Thx

[@Chineli09]

If I have the Mojave with no 2.5 lift just the stock suspension can I still slap them on or should I wait to lift it ?

[@vinuezaer]

Hope the bushings on that kit have improved. Mine (on my TJ) started too fall apart every 3 years or so. Company will sell you bushing replacements but they are hard to press in.

[@c130aviator]

I have a set on my 2004 tjr. Never needed bushings. Still on the same set.

[@CheaperJeeperTV]

Too funny! I am behind you in schedule. I'm researching doing this as well. I did my full width RR HD bumper if you wanted to check it out the look compared to your RR HD Stubby width. Cheers.

[@c130aviator]

Cheers

[@gvsukids]

would it be good to widen the hole that the pin goes in so there isn't as much force needed/worrying about dropping pin on ground?

[@c130aviator]

Grease it. I wouldnt widen the hole. Make sure you are on level ground. It will line up easily.

[@icehole503]

Man our JT's mod list's are so very similar.. I have had these since I did my lift. -bastage

[@c130aviator]

Nice. I recognize you. Great minds think alike.

[@miguelchacon1745]

Brandon now that I have my lift on I am going to do this instead of what I had before...I don't have a tool to cut the bracket so that sucks

[@c130aviator]

Use a cheap dremel with a cutoff wheel. 20 bucks.

[@miguelchacon1745]

@@c130aviator my wife has a dremel tool and I’m going to get a cutoff wheel

[@miguelchacon1745]

@@c130aviator I didn’t see a link to the JKS quick disconnect? Do you have one I’m not sure if that’s how you get paid for advertising

[@randycarter4529]

I am a little concerned about cutting the bracket on the passenger side. Are there any concerns with respect to the strength of the pin bending the brace?

[@JLLIFEOFFROAD]

hate unbolting sway links. Misty still needs s set the works with her new axle. Iv been using MC. know what would of made the cut quick n easy???? yep a plasma cutter :) lol

[@c130aviator]

Acetylene 😁

[@JLLIFEOFFROAD]

@@c130aviator ur not wrong, but a plasma cutter would be a little easier in tht tight space 😂😂

[@edwintorres5850]

Do you have like a quick disconnect sway bar end links on the rear of the gladiator?

[@c130aviator]

I removed the rear sway bar.

[@CheaperJeeperTV]

By-the-way...did you mention there is some part or bracket that can be used instead of cutting the metal tab? Can you provide me with a link to that info? Thanks

[@c130aviator]

www.quadratec.com/p/synergy-manufacturing/front-sway-bar-link-relocation-brackets-wrangler-jl-8855-02

[@CheaperJeeperTV]

@@c130aviator You're amazing. Thanks for the quick reply. For the cost, I'll just cut the tab too. I was concerned that maybe the piece remaining wasn't very thick, but I'm sure it's ok.

[@miguelchacon1745]

I did it I cut my steel piece of my gladiator to install my quick disconnect

[@c130aviator]

Thanks for the update. I am glad you were able to get it. Its not a bad install. Just make sure those bolts and slip pins at the axle are super tight or they will rattle.

[@Moufosboufos]

U skipped most of the installation…

[@johnthibodeaux5189]

Is there a way to install this without cutting anything?

[@c130aviator]

Only if you buy the synergy relocation bracket