JL Wrangler Turn Signal Lights Out Error Message and Hyper Flash Fix With Aftermarket Fenders

[@garychique1638]

Awesome. You really hit the nail on the head. You did not assume prior knowledge when addressing the audience. You took everyone by the hand to do this diy.

[@BCeesify]

Hi, was wondering if this same procedure would work with Oracle bi led switchback headlights? Everything working great, but hyperflash error shows up when I use the blinkers. Seems to reset after shutting off the jeep, only to give the code again next time I drive it. Thanks!!

[@christiandavidpicadofallas9754]

I got the same problem the message comes back again. Do you idea what happened??

[@garyvance5806]

It would it be correct to assume that if I changed my OEM halogen lights with LED's and i get the turn signal out message along with the fast blinking, I should follow your process and activate rather than deactivate the LED setting? Thanks

[@nerdtall]

when you do this does the vehicle have to be on or turned off or does not matter ... when i did this it confirmed changes but nothing changed

[@lizzietapper3204]

Does the cord & Bluetooth need to stay plugged in to keep the settings?

[@georgerichaud5363]

Thank you, i did not buy new fenders, just after market led sequential turn lights, with DRLs and another set of sequential led turn lights for the fenders. I tried resistors and thqy quit working except for the drls. I took the resistors off and they do work except fir the annoying hyper flash after I went in with the odm i lost the turn signals so now everything is back to where i started lol

[@georgerichaud5363]

Thank you!! Really appreciate all your guidance and help. Will follow up with manufscturer.

[@JP-sl1js]

I did all the steps it last for about five minutes and then it sends the error code for signal out and hyper flash on the dash what can I do to fix this? Thank you.

[@Thatwayplus]

I have a 2019 JL with the halogen package, I was able to successfully upgrade the headlight and fenders to LED without any errors from the dash. I just now decided to upgrade the taillight to LED but getting the dash error on both sides when my turn signal lights are in use. Will this be the tool to address my issues? I just will like to know before I make a purchase.

[@TwoFeatherChannel]

@willo Sandaya that's because the Jeep CPU isn't programmed to look for LED when you don't have the factory LED package. I have the factory LED package with my JLUR and changed the rear tail lights to Oracle LED Flush Mount and the CPU is looking for factory LED, so I got the warning on the dash

[@TwoFeatherChannel]

a Resistor comes with the LED taillights package for the Jeep owners who don't have the factory LED package

[@cmac6877]

why is it 113 degrees in the showroom?

[@jeremyumdenstock2992]

purchased and installed on 2022 JL 2D Rubicon. did not work as this video shows. problem still persists. Spent a few hours to disconnect the cables (several bandaids later on right hand to get in to disconnect), plugged in the 12pin & 8pin dongle to ODB Link. ODB would not power on using the dongle. had to reinstall back to factory placement. Installed ODB Link MX+ to the factory ODB connector and did power on. spent the $21 to get vin. went through the setup to deactivate, all the way to "says successul", gracefully backed out to the home screen. tried several variations, but the JL still throws error of front lights not on. sporadic turn signal blinking continues. All in all a frustrating experience. $ wasted, time wasted and hand all cut up.

[@georgerichaud5363]

Hi there, excellent video. Couple of questions thou, do we need to download the app and pair it with the vehicle before doing anything else? Thank you!!

[@BlackstarOffroadFullerton]

You will need to download the app first. Then plug the device into the obd port. At that point, you will pair the device with your phone via bluetooth. Fairly simple process. Good Luck!

[@Lefishn]

What bumper and tires are those??

[@georgerichaud5363]

Hi again, so I followed your instructions and i chose jeep wrangler 4xe . Got alk the way to changes applied succesfully and now are deactivated. However, the turn signals still hyperflashing. Did I miss a step?

[@andreweisenhower5440]

Same for me

[@christiandavidpicadofallas9754]

Hi there do you know why the message come back. I got jeep wrangler Sahara .2019 . Appreciated it, you help

[@BlackstarOffroadFullerton]

Were you able to fix it previously and now it came back?

[@christiandavidpicadofallas9754]

@@BlackstarOffroadFullerton hi 👋, yes just for 1 hours worked and back again the message.

[@BlackstarOffroadFullerton]

@@christiandavidpicadofallas9754 Here is what I would try. First I would go back into the LED light settings and change them back to Active. Probably won't fix it but try it. If it doesn't fix it, go back in and switch back to inactive. There are so many different led lights that we need to try both ways. Secondly, after changing the LED settings, go to adaptations, LED Light Settings, iRestart, then Body Controller - Power on restart. Then turn the key off and shut the doors until the Jeep falls asleep. After a couple minutes, turn the Jeep on and give it a try. Hope this helps!

[@mahidmalik7]

Doest it work on rear turn led lamps? Grand Cherokee

[@adananguiano2031]

So is this kinda like a tazer?

[@markdvorak3661]

Did you need to clear the error code or does it go away on its own?

[@NickBajpaiMusic]

Can you please include a link to a connector wire that’s compatible with this box like the one you got?

[@BlackstarOffroadFullerton]

Hi Nick. I went ahead and included the link. Thanks

[@luisan027]

can you fix the same issue using superchips/flashcal ?

[@BlackstarOffroadFullerton]

They are similar but I don't think the flashcal does turn signals.

[@miguelortiz391]

Thank u

[@lizzietapper3204]

Does the cord and Bluetooth box need to stay plugged in?

[@BlackstarOffroadFullerton]

Once the programming is complete, you can disconnect everything.

[@ec2499]

Found the bluetooth device but what exactly is that cable?

[@BlackstarOffroadFullerton]

The cable is needed to bypass the security gateway. This is not needed on older Jeeps but the 2018 and newer Jeeps require it.

[@ec2499]

@@BlackstarOffroadFullerton but what is it called? You dont mention it in your video

[@BlackstarOffroadFullerton]

@@ec2499 I put the link to both parts on Amazon in the paragraphs below the video.

[@georgerichaud5363]

I crested a small video call here are the lights. Hop you can see it

[@BlackstarOffroadFullerton]

I saw your video. I see that you went from a factory LED to an aftermarket LED. I am assuming that your harness was plug and play so I am surprised that your having an issue. I would call the manufacturer and talk to technical support. My gut tells me that something is not wired up correctly possibly within the turn signals and daytime running lights.

[@georgerichaud5363]

Forgot to mention that i still have the obd plugged into the red cables

[@BlackstarOffroadFullerton]

Hi George. Please read the updates to the paragraph below my video. Some fenders are fixed the way I showed in the video and some require another method. The second method required "activating" the LED and then clearing the fault codes stored within the body control module. Hope it helps. Please reply with the brand of fenders that you are installing.

[@jongomez72]

need help with this message me.