Table Saw Jigs, Simple, Effective. Unlock the Versatility of your Saw!

In this video in make a number of jig for the table saw which will enable you to cut tenons, bridle joints, half laps, mitre splines, rebates and every angle for 0 to 90 degrees.
Cross cut sled • Large Cross Cut Sled. ...
Shoji Lantern • How to make a Shoji St...
If you would like to support what I do:
You can buy me a coffee PayPal paypal.me/ManInShed
My Patreon / maninshed
Contact me @ [e-mail]
My New Whiskey Channel / @thewhiskeyshed.4105
MY Instagram / man.in.shed
The Whiskey Shed Instagram the.whiskey...
Man In Shed Tshirt Store teespring.com/stores/john-mcg...
Tools, Books and lights I use are here!! www.amazon.co.uk/shop/johnmcg...
Woodworking Books I Recommend
UK Link!
Collins Complete Woodworking Manual amzn.to/2uwQcq1
Workbenches amzn.to/38AnQKj
Complete Guide To Joint Making amzn.to/2NUBv7e
USA Link!
Collins Complete Woodworking Manual amzn.to/2Gp9IYc
Workbenches amzn.to/30PBeHO
Complete Guide to Joint Making amzn.to/36pAYjS

[@hondacrx7829]

You do have to spend some time setting the saw up... blade, fence, etc. But once done, the saw is great. Fairly compact which is Nice kzbin.infoUgkxXh-4_3-ZT1fFWP91ZV7iVqzElr0lEb-a I did get an Incra Miter Gauge which takes some setup as well. The stock miter gauge can be adjusted in the miter slot with a little painter's tape... this tightens up the side to side play a lot.

[@stephb8178]

Just got my first table saw so going to make all of those jigs and push sticks, thanks for posting such a useful video 👍

[@bradleytuckwell4881]

Congrats mate it’s always fun setting up and making things for a new toy in your shop

[@wharfrat360]

Also, check out 3x3 Custom's video "fine woodworking on a jobsite saw" that she posted recently. A lot of really good tips and tricks that compliment this video really well. You'll be making beautiful work in no time!

[@Maths_With_Mike]

My new favourite Woodworking channel! Such clear, comprehensive explanations. It's 9:15pm and pitch black outside, but I just want to go down to my shed and start making these jigs! Amazing channel.

[@MCsCreations]

Excellent jigs, John! 😃 Thanks a bunch for all the tips! Stay safe there with your family! 🖖😊

[@billyblackie9417]

It is good to know you don't need to make a jig just to do something once on a blue moon. I like how you clamped timber to your fence and inserted the picture frame. Great idea. Now that is something I really needed to know is how to make a straight edge on odd edging timber with no straight edge so your fence is no use

[@jackvanstrien]

Billy,you screw a straight board onto your odd timber,now you use your straight board against your fence.It is easy to do,take your time.\

[@billyblackie9417]

Now I see the purpose of the bigger push stick I made the thinner one now I will make the bigger push stick as safety using two point pressure hold is a major importance thank you

[@billyblackie9417]

I agree with you there is a great need for the bigger stick to push the timber but also to hold it down in place a real safety issue and the smaller stick to hold the timber to fence strong enough to lean it towards the fence while being able to guide it through easy

[@billyblackie9417]

I too will make the bigger stick as I have already made the smaller stick and John's video shows the need, use and benefit of the bog stick. Good man John

[@paulzirker706]

Great video John. Especially showing how easy it is to make push sticks.

[@three-phase562]

Great set of jigs, I really do need to get around to making a cross cut sled for mine. I made a taper cutting jig a while back using the UJK t-track, I find they are really good quality parts.

[@BobbyBiz]

I’m a newbie hobbyist woodworker and this video is great… I will be making all these jigs this weekend.

[@JohnMcGrathManInShed]

I'm glad you found it useful

[@dexterlichtenstein4935]

Pal, you have excellent videos. You explain really good.

[@JohnMcGrathManInShed]

Thank you, I'm glad you liked it

[@Jakstar19]

I just bought a Bosch GTS 635-216 and this is exactly the video I was hoping you'd make! Definitely keen to watch this video and make everything! Thanks John! Love your stuff

[@JohnMcGrathManInShed]

Glad I could help!

[@ballstank3904]

Is his a 635 too?

[@johnjensen5540]

Great video! Thanks!

[@JohnMcGrathManInShed]

Glad you liked it

[@prutswerk2]

Great video, all I wanted to know about making your own table saw jigs in one go!

[@JohnMcGrathManInShed]

Thanks 👍

[@artwegener4341]

I'm glad I found your channel! I have the Bosch table saw like yours and this video is outstanding for useful jigs I need to make. Thank you!

[@JohnMcGrathManInShed]

Glad it was helpful!

[@headstocktailstock]

Usefull jigs John.

[@Annaisineire]

Pure skill!!!

[@thedillydotcom]

This was great! Thanks 🙏

[@blackbeton3923]

Great great job , and perfect pedagogy , thanks a lot !! 🙏🏻🙏🏿

[@JohnMcGrathManInShed]

You are welcome!

[@wharfrat360]

Watching this along with 3x3 Customs fine woodworking on a jobsite saw video you could make some beautiful work! Great content in this video, definitely looking forward to the next one!

[@JohnMcGrathManInShed]

Thanks!

[@stevedockery3534]

Fantastic video my friend. You've really made it simple to understand. Planning on making these jigs for sure. Waiting for the next video. Thanks

[@JohnMcGrathManInShed]

Thanks 👍

[@MikeM-ox3nd]

Brilliant!

Great advice for people using a table saw John 👍

[@JohnMcGrathManInShed]

Cheers Tommy

[@rorycubaking9572]

Excellent video thanks very much.

[@JohnMcGrathManInShed]

You are welcome!

[@villageidiot8718]

Good collection of jigs. I think feather boards would have been a good addition.

[@darodes]

John, this stuff is brilliant!

[@JohnMcGrathManInShed]

Cheers David

[@HeliRy]

I recently was watching a fella, with a six-figure subscriber count, moaning about how people always comment on his lack of common sense safety habits. “My shop, my rules. If you don’t like it… I don’t know what to tell ya.” Not two minutes later, this dumbass nearly puts his hand into the tablesaw blade when his wonky thin-rip jig fails at the absolute worst possible moment. Only dumb luck saved him. It’s refreshing to see people like you constantly preaching good habits and safer practices 👌

[@KunoGroHoldertreff-B12]

Thanks for the informations ! 🙂

[@JohnMcGrathManInShed]

No problem!

[@therelaxingwoodshop7495]

Great video John . I will copy this one

[@JohnMcGrathManInShed]

Glad you found it useful

[@user-qg6fy4yp8t]

Great video!!!

[@JohnMcGrathManInShed]

Thank you!!

[@grahamtaylor989]

Brilliant

[@scsolutions25]

outstanding

[@fons7719]

It seems not too hard for me who are newbies. I’ll make them. Thank you.

[@bradleytuckwell4881]

Love all your jigs. But I just want to say when ever I need a thin strip of wood I always try and cut on the left side of the blade not between the fence and the blade. It makes for a safer cut.

[@michaelosullivan8325]

Nice one as always bud . Question where do you get your T track here in Ireland I copied your mitre saw station a couple of years ago still going strong I want to add a stop lock system to it but can’t get any T track

[@JohnMcGrathManInShed]

The Carpentry Store do all the UJK products Michael they will have some in stock. They are great to deal with.

[@fredosachoff]

Amazing! Seems your table saw cart is the same height as your work table - do you have track grooves in your work table so that you can park the table saw up against it and run the jig onto it?

[@bazanderson8283]

Good one John 👊 am looking to get a table saw soon so this will be super handy to come back and check again, thanks for sharing 🙏 I'm assuming you can use cheaper plywood instead of birch ply?

[@JohnMcGrathManInShed]

You can indeed, I just had some birch ply off cuts so that is what I used

[@billyblackie9417]

Excellent side rail jig and good idea with great uses. I'm making a side rail for my table saw but I'm going to incorporate your idea to sit down on it when I need it you gave me great ideas thanks. Where can I get runners to purchase I can make my own for the non regular things also the clamps you use on the table saw

[@stephb8178]

First to view. Nice one John

[@JohnMcGrathManInShed]

Legend!

[@aaronstill3810]

Great jigs John haven’t seen any new uploads lately hope your ok

[@JohnMcGrathManInShed]

I'm good thanks, Just really busy with work.

[@muradozkoc]

Thank you for this beautiful video. Can you share us the dimensions of the materials you use in this project?

[@davidhuggett9748]

Great vid as always. What machine wax do you use please?

[@JohnMcGrathManInShed]

It's Axminster machine wax David

[@red_shift6408]

If you have an MFT is the cross cut sled necessary?

[@roydaley3413]

👍

[@steviepower1958]

What would you buy first table saw or mitre saw for DIY projects

[@JohnMcGrathManInShed]

I had a mitre saw long before I had a table saw

[@jamesmcalevey6749]

John will your Bosch table take a dado blado

[@reaper060670]

Alri John mate.. Which Band saw would u recommend for a beginner pal?? I don't want to be stuck with a piece of shit now bro so I 'm hoping u know enough to help me make the best decision John.. Thanks for the great videos man,, Love this Jig video

[@JohnMcGrathManInShed]

the record power bandsaws are very good for the money

[@DOSTalks]

What is the name of the clamps running on the rails on the jigs?

[@JohnMcGrathManInShed]

Hold down clamps

[@KikaWaiAlae]

Can you speak faster? Geez, slow down...

[@traviswatts1305]

Way better to click through than to listen to you repeat EVERYTHING you say 10 or 15 times.

[@truth-ox3wz]

Who's going to take advice or tips from a guy who doesn't even have a quality table saw?

[@michaelosullivan8325]

A bad craftsman blames his tools

[@ballstank3904]

What model is your saw?

[@JohnMcGrathManInShed]

its the Bosch GT10-XC