How to Make an Ultra Battery (Step by step with each detail)

[@LearnEnglishWithMe34]

This is the far best diy battery video on youtube. This video is priceless 👍

[@joyofelectronics9782]

Thanks

[@WTF_BBQ]

I've been waiting for this video. You did a good job. I prefer this battery over the conventional lead acid battery. This one acts like a supercapacitor / battery hybrid.

[@joyofelectronics9782]

Thanks my friend 🙏 we’ve done it eventuality ☺️

[@edusoles3210]

feito dessa forma quanto tempo dura essa bateria??

[@ftwproject658]

Glad I found your channel. Great demonstration!

[@joyofelectronics9782]

Thanks

[@hamdisuatkalelioğlu]

Hi Friend! Best video i ever met. I think black /gray color negative lead plate is coated with carbon graphite and adhesive. As far as I understand positive plate would be coated oxide naturally while charging process. However in the relistic big current battery repair videos we see the positive lead coated with the red material like a mud or soil or cement. Please advise the details on which chemicals we may use to coat the positive plate or just melting the lead in the water is enough. and why you coated / applied the carbon over the lead plate for only one surface instead of both sides? Thanks

[@joyofelectronics9782]

Thanks my friend for this nice comment. Actually l explained in the video on the white paper on figure. Because of the working principle of ultra batteries we coated only negative plate👍

[@Philip-hv2kc]

The carbon will simply convert to CO2 on the positive plate when recharging.

[@aroundtheglobe9739]

That’s a great video. Thanks a lot bro.

[@joyofelectronics9782]

Thanks

[@johnslugger]

*I made one like yours. it worked good but it is dead by next morning. Needs way more PbO2 in order to hold charge for longer.*

[@joyofelectronics9782]

No brother probably your separator wasn’t good enough and probably it short circuited Please check it out. (Note: you get better charge holding result buy using more PbO2)

[@johnslugger]

@@joyofelectronics9782 Thanks. I made seporator thicker and it worked. You are the smartest battery maker on ALL of You-Tube and I have watched them ALL! Thanks so much for responding.

[@marian20012]

there is something fishy here...sulfuric acid should burn paper towel like fire...

[@johnslugger]

@@marian20012 *Not when it's at only 30% strength.*

[@joyofelectronics9782]

@@johnslugger that’s right

[@KhalidBikesReparing]

❤❤❤ nice video from Pakistan ❤❤❤

[@nicamarvin]

Thanks for Sharing, I believe that enhancements to the traditional Lead Battery is the path to the future not fancy batteires.

[@joyofelectronics9782]

👍you are right.

[@nicamarvin]

@@joyofelectronics9782 In your Hybrid Supercapacitor video(Lead Hydroxide/Activated Carbon) it is stated that it's only 100 Farad. That seems very weak compared to the pure lead acid battery you made(with spent negative battery plates). I would have thought that the capacity of the hybrid Super Capacitor would have been much greater.

[@joyofelectronics9782]

@@nicamarvin brother Supercapacitors never can store energy as much as batteries

[@nicamarvin]

@@joyofelectronics9782 Understood, but the chemestry(Sulfuric Acid electrolyte) and the Positive plate(Lead Dioxide) are basically the same as the Lead Acid Battery, could it be the Activated Carbon? Does The Ultra Battery you built behaves like a Hybrid Super Capacitor or more like the pure lead acid battery?

[@joyofelectronics9782]

@@nicamarvin hybrid Supercapacitors more likely behave like Supercapacitors. That’s why they can’t store same amount of energy as batteries. The difference between hybrid Supercapacitor and Supercapacitor is their operating voltage and partly capacitance. As you see the surface area of hybrid Supercapacitor’s plates are less than Supercapacitor.

[@emirlie]

Kurşuna çıplak elle dokunma hocam. Deriden nüfuz eder. Kanalın çok başarılı. Tebrik ediyorum.

[@joyofelectronics9782]

Çok teşekkür ederim kardeşim. Haklısın daha dikkatli olmam gerek.

[@altardosmilagres2]

E a autonomia?

[@clickbaitnumberone1403]

Good one

[@joyofelectronics9782]

Thanks

[@alfigs2148]

what is the white glue you use for the activated carbon? thank

[@joyofelectronics9782]

Sodium silicate

[@analitycs1303]

Excellent Job..!!! Maybe couldbe more biger..2.15 volts x 10 = 21,5 volts......!!

[@upsilonprime]

Would baking the plates after painting the active material on them, help?

[@joyofelectronics9782]

You don’t need to bake the materials. Just let it to dry.

[@amrradwan4279]

Thanks for your nice video, I have a question, in charging shall the voltage increase or decrease for the battery?

[@joyofelectronics9782]

Charging voltage should stable at 2.40 volts after increasing at that point. The voltage of the battery will increase of course

[@amrradwan4279]

⁠I saw the balance charger for battery shows potential decrease during charging, for that I am asking minute 19:19 in video. I hope you explain it to me

[@joyofelectronics9782]

@@amrradwan4279in this type of batteries the charging voltage increases as the battery is fully empty at the beginning. But it lasts very short time. This is the basic characteristics of these batteries.

[@amrradwan4279]

@@joyofelectronics9782I am so grateful for you🙏

[@charlielloydfiesta7793]

Tnx for ur video,❤ but i need to find where can i avail carbon activator?

[@joyofelectronics9782]

Simply order on internet

[@Philip-hv2kc]

Perhaps an aquarium hobby supplier.

[@wwabete2009]

Thanks again for the beautiful step by step instructional video. I will try to replicate it. The design is quite quite to say the least!

[@joyofelectronics9782]

Thank a lot my friend. Break a leg 👍

[@abbasal-zubaidi6265]

Hello my dear brother, I want to make a single electrode, not a super capacitor, 5cm long and 5cm wide, and it is coated with carbon nanotubes. Should we take one electrode out of it for examination or two?

[@joyofelectronics9782]

Hello, two would be better

[@abbasal-zubaidi6265]

@@joyofelectronics9782 Is it possible to take the test if there is only one?

[@kerembolukbas7435]

Merhaba abi, kurşun plakaları çinko yada kalın alüminyum folyo ile yapmak sonuca nasıl eder ?

[@joyofelectronics9782]

O zaman elektroliti değiştirmen gerek ki farklı bir batarya elde etmiş olursun.

[@kerloesmedhet3480]

Well, how can we make an electrolytic capacitor out of aluminum? I have requested that from you a lot and I am waiting for you to make it

[@joyofelectronics9782]

Brother l know that, l remember very well. It is very is to make. However due to change my home nowadays l am over busy so l can’t find enough time to make video for a while. But l will make a video about it ASAP🙏🙏🙏

[@kerloesmedhet3480]

@@joyofelectronics9782 Thank you brother for your interest, waiting for you as soon as possible

[@kerloesmedhet3480]

@@joyofelectronics9782 Congratulations on your new home

[@joyofelectronics9782]

@@kerloesmedhet3480 thanks a lot my fellow 🙏

[@jozefnovak7750]

Thank you!

[@suprayogi340]

I often hear, please, what are examples of brands of white glue pk....such as fox glue or white glue for wood??slm have a nice dy from indonesia tanks for god your content

[@joyofelectronics9782]

Thanks. Wood glue or fox glue works well.

[@suprayogi340]

@@joyofelectronics9782 ok, thanks boss...I'm trying to make a supercapacitor to be applied to an electric bicycle, please support it in the future, greetings are warm and healthy, always have a good night

[@neonsoft21]

You should have worn gloves the whole time😅😂😂, still good video.

[@joyofelectronics9782]

Yeah you are hell right😂 but sometimes it’s difficult to work with gloves. However l washed my hands with plenty of water and soap right after the video 😂

[@dkjawahar-techexpt671]

Nice demo and useful information for us, thank you for your efforts. From Jawaharlal Bharat INDIA 🙏. I saw you have connected the negative terminal with the centre positive, will it not discharge itself?. The two negative should have been soldered as one Neg and centre as positive.

[@joyofelectronics9782]

Actually l didn’t connect the negative to positive. I connected the negatives together but when l applied the active material to the negative electrodes l made a mistake. So when l solder the negative electrodes due to their positioning it seems as if l connect negative electrode to the positive one☺️

[@realflow100]

@@joyofelectronics9782 Ive made same mistake with negative electrodes. active material applied to the wrong side of one of the electrodes.

[@shrishailutagi7223]

👌

[@NoLimits_Kino]

You made a 3amp 2volt lead acid battery. 👏👏♿️

[@محاضراتالالكترونية]

Where can I get activated carbon?

[@joyofelectronics9782]

You can order on internet

[@محاضراتالالكترونية]

@@joyofelectronics9782 My situation does not allow me to order from the Internet. Is there another solution, such as a way to make it at home?

[@محاضراتالالكترونية]

@@joyofelectronics9782 I have another question: how do I know the appropriate electricity for charging, as I do not want to charge it with a strong charger or a weak charger and thus it becomes damaged?

[@lmeseguer001]

​@@محاضراتالالكترونية Look up for water filter cartridges or check up supply stores for cosmetics/cleaning products, the kind of shops where the handmade soap-makers and wax canddle makers usually go for their supplies.

[@ahmed-najdi6818]

ماهوة حامض قبلة الشخن البطرية

[@joyofelectronics9782]

Sulphuric acid solution in water (30%)

[@ahmed-najdi6818]

@@joyofelectronics9782 ماهو حامض الكبرتييك

[@bilalkhan-ki8gc]

❤

[@ioantordai3904]

❤️❤️❤️❤️❤️❤️❤️❤️

[@chandravirteotia2009]

Kind give description in hindi also

[@joyofelectronics9782]

👍

[@chandravirteotia2009]

@@joyofelectronics9782 Thank you very much for quick response. Description given was felt tremendous and well educated. I would feel good if you give the explanation in hindi.

[@joyofelectronics9782]

@@chandravirteotia2009 you are very welcome my friend. I would like to give some explanation in Hindi language, but can’t speak any Hindi language and it is very difficult to translate the whole video. You can open subtitle in Hindi. I will try to do something anyway