Great video Ed. I'd love to see one where you change the bearings.
@Coyote9732 жыл бұрын
Thank you, very helpful video. When I pulled out the rotor from casing, the shims stuck on magnets. I am not able to determine the correct position of them. The only exploded view I have seen so far, is the one you have it. Can you upload it somewhere, since the link in the description is broken. Thanks.
@jayc31104 жыл бұрын
Thank you for that very clear and helpful video.. your disassembly instructions helped me clear out a stuck burr! That solves one problem. The handpiece I have seems to be running fine now. But I have another problem with the control unit also. The motor runs only at one speed oh, and I don't know what that is. The control knob does not change speeds at all. Have you had a problem similar to that? How do I get my speed control back? Have you ever had a problem with the control box itself and do you have any experience with fixing the speed control? Any suggestions from you will be very helpful, thank you again.
@jaimefilho49592 жыл бұрын
I have had this problem on Marathon 3. It's a transistor failure inside the control box, caused by an input voltage problem. Replace the transistor should be resolve it.
@jayc31102 жыл бұрын
@@jaimefilho4959 Thank you for your response...
@longdriver26 жыл бұрын
Ed, nice instructional video. Very helpful. Where did you get the parts list? Thanks
@kpvillester6 жыл бұрын
Thank you so much for your instructions !!
@EdPitts19336 жыл бұрын
You're welcome
@iwin49852 жыл бұрын
Where could I find a COLLET CHUCK or Wrench to remove the collet? I can't find it at Patterson or Rams website.
@djomlastic10 жыл бұрын
Saeshin strong 90n micromotor is very similar. Thanks, this helped me a lot.
@kpvillester6 жыл бұрын
Where can I find the diagram of the hand piece parts list ??
@EdPitts19339 жыл бұрын
For anyone, once you have taken the unit apart, changing the bearings is simple. just slide the old one off and the new one on.
@VioletIndigo33 жыл бұрын
I don't know how to take the c clip off.
@rwolk84835 жыл бұрын
HEllo Ed, How to you remove & replace bearings on both sides armature?
@hereshmehrzad82317 жыл бұрын
thank you sir i repair my saeshin micromotor with your demonstration and advice
@EdPitts19337 жыл бұрын
I'm Glad it helped.
@ramproductsmicromotors886710 жыл бұрын
Common spare parts are listed on www.ramprodinc.com website and available to order as well as all parts needed
@القيصرالقيصر-ذ1ز2 жыл бұрын
سلام ممكن شرح اسباب عطل البيرنجات حق ميكرومتور ماراوثون
@EdPitts193311 жыл бұрын
Thanks, glad you like it.
@hannekebosselaar-pater26243 жыл бұрын
My engine burned I think.... Van In fix it?
@naveenbadri20813 жыл бұрын
❤️ from India
@bouhadjamoh29706 жыл бұрын
would you like to send me the exploded marathon schemac 35 000 rpm so i can order the different parts by reference.thanks
@marcelosantosdacosta6 жыл бұрын
Olá vc saberia me dizer estou com uma caixa de controle da caneta ela só funciona em alta
@eyamnottier34114 жыл бұрын
Can anybody ad a link to that parts diagram the link here is in Estonian ....and been able to find the right link.
@AFishTale10 жыл бұрын
Can you share where you purchased the bearings. Ram says they won't sell them. They said to sent them the hand piece.
@EdPitts193310 жыл бұрын
I bought mine from Ram Products. I don't understand why they would not sell to you.
@davevankerr9 жыл бұрын
you can buy them at ldental.com too.
@EdPitts19339 жыл бұрын
Thanks Dave, good info.
@davevankerr9 жыл бұрын
Hi Ed. I distribute Ram Products in Canada. If people are interested in parts or new equipment in Canada they can call 1-800-667-3770.
@mohdasifasifkhan98895 жыл бұрын
Hello sir please what us reason heating problem
@laumcr995 жыл бұрын
Muchas gracias muy útil
@vijaybalnathkhaire54326 жыл бұрын
I'm looking for portable micromotor with lethinium battery
@leokadiaigrzegorzfiuczek59347 жыл бұрын
hello, did you have diagram of voltage regulator?
@EdPitts19337 жыл бұрын
Grzegorz Fiuczek no. Sorry I do not have wiring diagram
@jawedzia10244 жыл бұрын
I am jawed from karachi Pakistan I am fully repairing and 50`000 rpm waindar call 0093142176669
@smarzouk828 жыл бұрын
front armature bearing won't come off any suggestions?
@EdPitts19338 жыл бұрын
Penetrating oil?
@paularodriguez235210 жыл бұрын
qué es lo primero que saca?
@BenKordellАй бұрын
zzzzzzz.......zzzzzzz Buen video de hecho pero muy lento 😅
@Pinkielover4 жыл бұрын
junk handpiece. i know the owner of the company that makes these.. my father was in this business for over 45 years .. need parts i have some still left from my dads old repair company.. nsk so much better