HOW TO REPLACE UNIVERSAL JOINTS ON A MERCRUISER

[@johne.bruder9636]

Thanks buddy! Your video has been very helpful and entertaining. I like the buzzer when making a mistake keep them coming for us rookies.

[@brianbercier5560]

great video, I have to change the u joints on my mercrusier and now you made it a breeze.

[@markjennings2315]

I used 2 sockets and a G clamp. worked really well, took 20 mins!!

[@mumbles552]

Thanks for posting this! I wasn't sure which way to install my new Moog greasable U joints but now I do!

[@Ralph-PeterBerlekamp]

Super Video, hat mir sehr geholfen. Vielen Dank dafür!!👍

[@markjennings2315]

This looks a good one to do. The bearing pusher looks like a G clamp!! I might adapt one for this. thanks for posting.

[@Vincent-sb7vh]

Excellent video😊😊😊

[@nbeck956]

Great Video, thanks for putting it together

[@rubensandoval7052]

Great video man, you made my job a lot easier thanks 👍

[@majbach1968]

Thanks for posting this.

[@ashipshow]

You're welcome

[@pkonolan]

That is amazingly easy with the C-clamp. I have essentially the same size one and will use it next time. I actually used an old socket to provide the sleeve to catch the bearing cups and tapped them out with another socket and hammer then re-pressed them with a large bench vice. I can actually, I imagine, do the same with the sockets and the C-clamp.

[@Lolindir_Fox]

I'm about to restore a 1979 mercruiser, it's an Inboard/Outboard but I feel this is very heplful because I was told the ujoints needed replaced thanks for the video I'll be looking at your others here

[@hughtullosiii706]

Thanks, Buddy.

[@harleymutt8542]

Very helpful! Great job

[@Cregdidit]

Good job. now I can do my u joint 👍

[@kubaSWAT]

Where did you get that adapter?

[@110welding]

thx, i am aboat to do on my boat and had no idea where o begin, lol

[@naiefelyemeni1986]

my ujoints are very loose floppy ? is that normal ? they look clean and like new

[@neverclevernorwitty7821]

Well, I got one cap off my first cross without damaging a tooth. The next cap took out two at the same time as I tried to thread it between them. Clean breaks. Doh! I just recently bought a similar mercruiser, and dear God the caps on some of my joints were bone dry!

[@jasmine13370]

What was the year on the out drive and the Sierra part number?

[@jkgkjgkijk]

I did this before covid. It was a major pain in the butt. Lots of banging. I never would do it again.

[@tjmcclain9004]

If I have a boat mechanic do this job for me, how many hours would this job take, or what should I expect the cost to be?

[@ashipshow]

probably a few hours, but they are probably going to tell you while you're at it to replace some other things... no idea on cost, ive only ever worked on my boat myself :)

[@mzsoria530]

So my husband replaced our u joints in our boat when we put it back together now when we start the boat its in gear? did he do something wrong?

[@ashipshow]

My guess would be the shift cable was not in forward when the drive was reinstalled and its not engaging the cable correctly

[@mzsoria530]

@@ashipshow any idea what we can you to fix that? or are we going to need a mechanic?

[@davidanfora5473]

I am new to boating and have a Mercruiser 5.0 with a Bravo 3. I'm just trying understand the basic principles of the engine. I appreciate your video to see the inner workings, but could you explain to me the "how"? Or maybe post a 3 minute video? I just cant seem to find it on the 'net. Specifically, how do the u-joints work. How does the drive shaft spin, etc. I am most interested to understand why you can damage the u-joints if you trim up into the trailering range while underway. Mercruiser says it is safe to do so while below 1200 RPMs. A reason I could see to do this would be to access shallow water areas that we enjoy. But the general boating community seems to say, "Dont ever do that while the engine is running at all, because it puts too much stress on the u-joints." I dont want to harm my engine, but I dont want to succumb to undue paranoia either. So could you explain to me the how/why of that? I would really, really appreciate it if you could. Thank you!

[@ashipshow]

A general mercruiser sterndrive system overview is not a bad idea... unfortunately I probably wont have time to make something like that until later in the fall when work on my boats slows down. Thanks for watching

[@81randallchadcohen]

Great video! I have a question for you....... When my sterndrive is straight, I hear no noise whatsoever, however when I turn the wheel in either direction I get a horrible knocking/clunking noise until I bring the wheel back to straight position. My engine alignment tool slides with 2 fingers effortlessly in and out, etc.... U joints appear in good shape, no slop and taking grease. Cannot figure out where the clunking is coming from. Any guess? Thank you for your time.

[@ashipshow]

Definitely sounds like bad ujoints. If your gimbal bearing hasn't been changed in a while, might start with that, but odds are its u joints

[@81randallchadcohen]

@@ashipshow Thanks dude! The sterndrive was off the boat for a year so maybe they took a beating during that time, as it was a yard. The weird thing is that before the repower, the sterndrive was smooth, no noise. I'll start with the bearings and u joints. Thanks again - going to watch ur video a few more times!

[@kubaSWAT]

What Ujoints did You buy finally? Thanks!

[@ashipshow]

I'm trying to find the ones I bought... it was quite a while ago so I don't remember off the top of my head... If I find it, I'll let you know

[@ashipshow]

Just watched back and the sierra boxes say 18-2174

[@kubaSWAT]

Madprops Boatworks Thanks! Permalube?!

[@ashipshow]

@@kubaSWAT Nope, these have grease fittings... I pull my drive every winter for maintenance anyways, so I'm not worried about remembering to grease them.

[@brandonprettyman269]

Should have just cleaned up old bearing caps and used them with first pair of u joints so clips would fit

[@matthewwheat3820]

DO NOT CUT CASTLE NUT! It's only 4 bolts and a nut to take drive shaft our of upper and do right.

[@gamingandmore682]

My ujoint is hanging in the gimbal housing do i do

[@gm1937]

This is very helpful however, please leave out the romantic music because I keep hugging my wife instead of working on this project

[@clecollins2673]

snore

[@ashipshow]

Have a good nap?