This was great mate, keep it up!!! Enjoyed the little parts with the gauge and sensor's and the waste gate spring too
@house-ofhoon3 жыл бұрын
Cheers mate! Glad you enjoyed those parts 😁
@elmotheewokking2 жыл бұрын
Glad I'm not alone in thinking the JRP gauge is incredibly similar to the Defi copies doing the rounds...
@house-ofhoon2 жыл бұрын
Definitely similar. Some good improvements on the JRP though and better quality
@timspears22283 жыл бұрын
Yeah buddy, clever move with the air intake temp! Keep it up 😀
@house-ofhoon3 жыл бұрын
Cheers mate! The AIT sensor is definitely coming in handy 😁
@mickeyblackice36943 жыл бұрын
Good stuff like to see the numbers after Dyno. Have fun
@house-ofhoon3 жыл бұрын
Cheers mate! There will be a video of the dyno coming soon!
@nathanhughes99962 жыл бұрын
Another awesome build mate, a few ripper quotes *the speed of 1000 gazels* 😂. I have a multiguage ready to hook up also so this was relevant to me Did you make your red steps and scrub bars? They look awesome 😎
@house-ofhoon2 жыл бұрын
Haha cheers mate! Picked that one up from the Army lol. Yep, I sure did make the sliders and brush bars, thanks man 🙂 Best of luck with your multigauge install! 🤙
@jonesy11303 жыл бұрын
Great vid, got a JRP unit myself and cant fault it! Did you end up swapping the AIT to both sides of the intercooler to see the temperature difference?
@house-ofhoon3 жыл бұрын
Cheers mate! No, I ran out of time. I'm planning on doing a video comparing the two though 😊
@jackpapworth35772 жыл бұрын
Very helpful cheers
@house-ofhoon2 жыл бұрын
Glad you liked it mate!
@madcat4563 Жыл бұрын
0:44 Mmm, I wonder what happens next. So it sounds like the JRP kit is a definite upgrade over the defi knockoff? I mean, the defi clone is pretty cheap, so I can understand why the cables, wires, and sensors are not as good.
@house-ofhoon Жыл бұрын
Yep the JRP kit is definitely a good kit and an upgrade over the defi clone 👍
@jamesgill40353 жыл бұрын
Enjoyed the vid. :)
@house-ofhoon3 жыл бұрын
Cheers James!
@DarcyDevine3 жыл бұрын
What is that contraption your winch is hooked into on your bullbar? Thanks mate great video
@house-ofhoon3 жыл бұрын
Cheers mate. It's my first attempt at a 3D printed winch dildo to suit my specific application. I need to print a V2
@donaldwills21353 жыл бұрын
29psi is a bit high haha. I run less then 20 with a 250hp 12mm pump
@house-ofhoon3 жыл бұрын
Haha yea the tuner turned it down to 23psi 👌
@donaldwills21353 жыл бұрын
@@house-ofhoon what did she make
@house-ofhoon3 жыл бұрын
Trying to keep it hush hush at the moment until the video comes out sorry. But it's a healthy number considering its still got the factory pump
@donaldwills21353 жыл бұрын
@@house-ofhoon thought as much I'll keep a eye on posts
@Berawabilly3 жыл бұрын
I run 32psi with a ufi 250hp pump. how much power you making?