Jumper T16: A lot of radio for the money

[@Dav2112]

Man, the more reviews I’m seeing of this radio the more I want one, looks really well made inside and out, think I’ll hold onto my X9D though as I’m so used to it.

[@marsrover001]

A note on adjusting gimbal tension. Remove the rubber hand holds on the back and there's holes that go to the gimbals. You don't have to take the radio apart at all.

[@h2o-fpv623]

I justo got my jumper T 16 im so hippy that i got this radio now im going to watch all ur videos I like the way u explain everything thank u for this videos.

[@iam.miikey]

This looks like a nice all around Radio especially for long range. I just pre-odered one yesterday. I was looking for a second radio to compliment my DX9 for intermediate and long range flying for a couple of wings and copters I want to upgrade. Hopefully, jumper Tx will be supported in the future. I didn't like the long range options for Spektrum DX9 and I've been looking at your video series on OpenTx to learn more about it's capabilities ie setup, configuration, telemetry, lua scripts etc. And now this little gem has come along and it fits my needs without breaking the bank. Looking forward to your future inav and jumper Tx videos. I would like to see how well the T16 performs with both the R9M module and the Crossfire. That will be my next purchase. Keep up the great work. I always look forward to your videos when they come out. Cheers!

[@k.d.r.ckevind.6855]

Did u notice that the gimbles raise up and down,, just tight or lossen the screw that is found on the stick gimbles themself,, on then inner right on the left stick, and the inner left on the right stick.,, Or i may have that backwards, but either way, i dont believe ive ever seen that ever b4,, way to go jumper,,,

[@S700KYFPV]

As usual another fantastic and well presented and informed video from start to finish, covering all the right points. Legend 👻

[@Sam-gr8pl]

I really like the radio... thx for the review Lee.

[@daviddunn2503]

The first day i had my Jumper t16 the roller bearing pin snapped off the roller has two functions ie it rolls to scan and can be pressed down to "click on an item. faced with the prospect of a long wait i drilled out the end of the roller and fitted a new pin of hard plastic. All is now well and am pleased with the tx, but beware of being heavy handed "clicking" the roller

[@Painless360]

The early T16 models were plagued by issues. That's the reason I stopped making videos on it as they weren't doing a great job helping pilots who had a faulty unit. Reports suggest it's a lot better now..

[@Barbaric_Iron]

All of these Jumper radios are awesome.....indeed their in the big league now...This will be my next radio!! TFS!!

[@k.bellingham8335]

Have you ever heard of or saw a radio tx where the joy sticks had a third channel? First I am assuming that a typical 4ch flight controller has two separate channels per joy stick. One stick operates for example throttle and yaw, the other stick, pitch and roll. What if the sticks had a third function, what if one could rotate or twist or dial the stick/s all while remaining in full and proper control of the air craft.I figure if anyone, your the feller to ask.

[@Painless360]

I've not seen that myself but it's an interesting idea! If you find one please let me know.. Happy flying

[@k.bellingham8335]

@@Painless360 Thanks Lee, will let you know if found

[@bigfella6629]

I'm not going to rush out and buy this TX, still reports coming in that the roller button is breaking and that's on retail version not review version. Once this is fixed I may looking at purchasing it.

[@Nelsonv2]

Alert !!! I just got the Jumper T16 Pro. To work with dsm2 and dsmx receivers BOTH internal RF and external RF have to be ON in the model setup menu. After hours trying to make it work with the internal RF only and no response I try both on and wala!! works.

[@richardcerni9996]

I was eventually going to get a Taranis, but now I'm going to have a re-think. I currently run Spektrum, Flysky and Turnigy. Only one other question - I am a dedicated mode 1 flyer......that's how I started and evolved. Can this radio be changed around to mode 1, electronically, or otherwise by opening her up as you did and swapping some things around. Thanks for the review by the way - very informative.

[@marto2200]

I've watched a few reviews on the T16 and am impressed. Will resist the urge to rush out and buy one and wait and see if there is a plus model with hall affect gimbles. Great review as always. Clear and consice.

[@thezebiano]

Do you have an ideia when it might come out? Like, in a month or in a year?

[@MrFravy]

I wish to know too,when come plus model

[@robertpetrosky3067]

hi lee I am now an official patreon I have learned so much from your channel and you are awesome ..!

[@Painless360]

Thank you for becoming part of the inner circle! :D

[@bigfella6629]

Nice radio but not liking the antenna setup on the external module, may still buy it solely on price over the Taranis X9D that I was going to buy.

[@ojkolsrud1]

Can't you just replace the antenna with a longer one?

[@kenspaceman3938]

I read the T16 manual and it shows a companion software used for many things, only it seems to be in Chinese although the screen captures are then commented in English. Is this an official Companion software by Jumper for the T16? As the OpenTX Companion doesn’t have the T16 listed and seems to corrupt the contents of the as card. Happy to see that country can easily be chosen in the settings menu of the T16 radio controller.👍

[@Painless360]

See my T16 series.. I cover it in there..

[@IceCreams62]

The rolling control on the right of the screen is very fragile internally on one side but it seems to be a very good Tx

[@kenspaceman3938]

Can the Jumper T16 transmitter be flashed to EU-lbt firmware? Can I flash FrSky receivers with a cable from the transmitter to the receiver to be flashed? Like it works on the Taranis Q X7?

[@GStrauss]

Another great video! Thanks! I have a Taranis Plus for 2 years, and got 6-7 FPV models, all flown with a Dragonlink slim v3 which is attached in the back. Should I consider the Jumper T16 as a better replacement? Can I import all my models?

[@Lagggerengineering]

I'd love to see how to set up telemetry on that nice screen! I also saw on the product website that they support a third party widget for telemetry. Can't remember the name, it's at the bottom. It was used for Taranis radios, including Horuses.

[@Painless360]

You're not following me on Instagram are you ? ;) I'll be looking at that in a coming video as there are excellent free telemetry LUA scripts that are great for iNav and Autopilot on things like Omnibus.. Stay tuned!

[@Lagggerengineering]

@@Painless360 You got that right, I don't have an instagram XD Thanks for letting me know! Looking forward to it!

[@MikeDronesEnt]

i just got this radio today and i'm having some problems with it straight out of the box. it turns on fine. but when i hold system then release it. the menu switches instantly over to sd-hd card menu and the page button does nothing. the page button works though. if i press and hold it, it acts just like the system button.

[@MikeDronesEnt]

so after taking this radio apart all the ribbon cables looked fine but i re-seated the one that went into the board for the sys and page buttons now it works fine! hope this helps anyone else

[@artsmodelstation9396]

Q: if I set “flight time” timer, does it have voice alerting or is it just a beep ?

[@Painless360]

You can set either..

[@FlyNasty]

Great review!! The only feedback I have for Jumper is change the USB port to something more current.. those type of wires are hard to come by these days

[@robertpetrosky3067]

hope your going to come out with some TBS crossfire videos with the jumper T16 cant wait to see some ..!!

[@alexongpanghai]

Can show how to setup 6 flight mode for pixhawk fc with this transmitter? I used flysky i10 but never used jumper transmitter or frysky before. Thanks

[@Painless360]

kzbin.info/www/bejne/lX24g4ermNytpZI ;) You can support me on Patreon if you found that useful..

[@myshots101]

I didn't see this, but is there an option for helis on this radio? Just curious.

[@Painless360]

Not via a wizard but it's possible - Google 'painless360 opentx heli' to find my video on it..

Do they have a manual for the jumper t16 , I can not find one ?

[@gavinvales8928]

i was thinking of getting the nirvana in a while, but this radio has just blown my mind

[@perbackman8283]

I have the T16 and i cant bind the Wfly receiverrs or the fly sky fs-ia10b any idea why ??

[@lalithkishore3774]

Can u make a video on how to bind jumper t16 to any receivers

[@carlhudson9001]

Great video Lee. I've just ordered one of these and can't wait for it to arrive. I have always used Spektrum so Open Tx is something I have no idea about, it would be great if you could do some basic walk through and set up videos to teach us converts how to use it.

[@Painless360]

Ok, will do. I'd also recommend taking a look at the OpenTX mix school on the channel as it'll give you an idea of how to setup some stuff..

[@josephbove528]

I just got my T16 and it's defective right out of the box. There is static coming through the speaker. As the screen dims it gets louder. They may have some quality control issues with this product. Tried various settings and there was no effect.

[@Painless360]

Sadly there do seem to be a few issues with the radio quality now. Sounds like you need to return yours...

[@josephbove528]

@@Painless360 It's on it's way back. By the way your channel is fantastic. Thank you. Cheers!

[@josephbove528]

@@Painless360 The other issue is the model setup menu. It only shows 4 options. I'm not able to delete a model!

[@Troops-y6h]

Has this radio got pitch and throttle curve for heli's?

[@Painless360]

Yes

[@kkuenzel56]

Great video! I have one on order but I am a total noob with Open TX. I would love to see an "Open TX for Dummies " video.

[@Painless360]

See the series for the other OpenTX radios as well as the OpenTX mix school pkaylists on the channel for that, I will do some setup steps on this radio too as I've had enough interest. Thanks for the comment..

[@kkuenzel56]

@@Painless360 That would be very much appreciated! I just got mine yesterday and I'm pretty overwhelmed with all of the settings.

[@h2o-fpv623]

If u can make a video about getting the radio to used it for practice with a simulator.

[@h2o-fpv623]

Nice video I'm getting mine today .

[@jelly-qs5fy]

Hi 👋 just pre-ordered the jumper t16 plus & am extremely excited & probably in over my head as this is my 1st radio! Anyways would you be able to do a how to video setting up a model with the horizon as3x safe technology on the radio... I own the horizon sport cub s and would like to use with this radio... thanks!

[@Painless360]

Unfortunately I don't have access to any Horizon Hobby planes.. best of luck!

[@fredkaz245]

I have read on a few Forums and facebook pages, that people are getting Low/Critical RSSI Warnings when using the DSM Protocol, I my self have had the same problem with a Bind and Fly Spektrum Helicopter, getting Low RSSI warnings at about 5 foot high close to me, move away by about 15 feet , i get the critical warning. Looking at all the replies to the post that I have seen, it looks like the solution to this is just to turn off the RSSI warnings in the telemetry page. Do you know if this information is correct?? I have installed both the latest firmware from OpenTx and also the latest firmware for the Multi protocol module. I am not technically minded and from what I have read, it looks like these bind and fly stuff or any spektrum receiver which is not telemetry based, confuses the handset and gives a false warning. Apart from the walking 30 paces from the model and do the range test is there any other test to see if the module is working properly. it would be good if you can look into this as with your background in electronics you might be able to understand and technical information from either OpenTx or Jumper RC themselves.

[@Painless360]

Range test is the best way as that also checks the local environment for noise too. I also have the ImmersionRC Power Meter V2 that you can use for that as well..

[@probante]

ordered one to use with my dragonlink system. Hope it'll work fine. let's see. thanks for the nice review

[@short5stick]

I have the jumper. Please do a video on setting up a 4 aileron with a 3 position switch. Up all ailerons work as aileron,middle switch 50% flap down ,down switch 100% flap all with down elevator trim. Only the 2 centers will be flaps and the outer will be normal ailerons. This would be great.

[@Painless360]

OpenTX is OpenTX so all of my OpenTX videos are relevant to the radio. I'd suggest my Advanced Plane Setup video. Best of luck!

[@short5stick]

@@Painless360 I did it I did it. Use 2 aileron and 2 flap in model setup in the mixes copy flap change source aileron,switch to SA up position all 4 work as ailerons. I copy flap for each switch position and set offset for 50% middle switch and offset to 100% for down switch for flaps Now go to elevator and copy and set to position middle and adj offset you need for trim down and copy again for switch down position. That is how I did roughly it and it works. Took me 5 minutes now I can do it even less time.

[@saltvatten]

How large is the throw in the gimbals compared to a X9D+?

[@Painless360]

Slightly less, It is not something I've noticed using it myself.. But then, I'm not a stick banger :D

[@saltvatten]

@@Painless360 How is it compared to the Frsky X-lite? I am in a hasty need of a new radio since my X9D+ broke yesterday and I find that the gimbals in the X-lite is too small. Is the gimbals in the T16 comparable to the X-lite? Thank you very much in advance.

[@HyvelTjuven]

Can you flash an XM+ with EU firmware using this radio? Thanks for the review!

[@niranjan1948]

I'd love to see and video on a inav plane setup with this tx and differential thrust mixing on the transmitter

[@Painless360]

You wouldn't do that in the TX. Youd set that up in the iNav mixer.. see my latest iNav2.1 build.. happy flying!

[@tomaskonkol8894]

Hi Lee, thanks your great video content. My t16 arrived nearly 2 weeks ago and its great or was great. but i have problem possible with module and looking for somebody around MCR to test different module to confirm if its just module faul. radio its working and also i have correct voltage on on pin 2-3 but module not detected by radio.

[@ChrisBalmforth]

Great review as usual! Lack of Companion support would kill this for me, I hate setting up my FRSky radios manually. I know that the T16 isn't officially supported by OpenTX but are you sure that you can't use Companion to set up models and load them onto the T16? The feature set looks identical to the FRSky X10 so I would try using it with the X10 profile.

[@Painless360]

It's something I will be testing as the hardware layout is very similar...

[@SuperZerofreak]

Does it support JR DMSS Protocol?

[@interman7715]

Hooray finally a Chinese radio that looks good ,finished well and it is full size ,they are gonna sell millions of these.

[@jackholding9010]

I'm in the market for a transmitter upgrade from an old FS-i6. Want something with opentx. So would you recommend this over an Frsky radio?

[@Painless360]

Not at the moment. Stay tuned as the next best thing is due in very soon....

[@jackholding9010]

@@Painless360 OK thanks for the reply I take you will be showing the video soon?

[@mithrandir1313]

So I wonder how much of that radio is Futaba?

[@Billbobaker]

Nanny of the Jetsons for sure.

[@akselhansen7670]

With that fine screen is possible to setup telemetry with pixhawk and some receiver like frsky xsb? (no need for 433mhz mission planner telemetry with ac quadcopter?)

[@Painless360]

That's something I can look at as the LUA script shown on the package does look like the Ardupilot/pixhawk one I've looked at on the channel..

[@RType2966]

just got my jumper t16 and want to connect to my Frsky Xsr Eu lbt. what settings would I need to change on the jumpter T16 cheers ;)

[@maixechrys6264]

T16 with the cheap telemetry you did with omnibus but this time with pixhawk! I think the screen is a very good selling point really makes it seem more modern.

[@kayakconfessions4121]

How do you set up dual rates for fixed wing?

[@Painless360]

See the OpenTX on school playlist.. best of luck!

[@kayakconfessions4121]

You got a link?

[@Painless360]

Please see this video - kzbin.info/www/bejne/hmXWoIVshsyCoZI - that should help you find those videos of mine and help you find the answers you need quickly

[@PcandTech]

I would like a case and better gimbals, maybe the m9 gimballs fit?, also I would like to see things like latency and range vs the original

[@NATGEOANDSTUFFPaulbrannan]

looks great this one.love it.jealous lol.great review buddy as allways

[@smnaol80]

They fix the ROLLER button?

[@Painless360]

Mine isn't broken...

[@Cristianxb]

Hi There, Your videos are helping me a lot getting started with this hobby. Now its time to buy a Transmitter, I cant decide between the Jumper T16 and the FrSky X9D Plus. Which one will let me keep progression in the hobby for a long time without the need of changing the equipment? THANKS!

[@Painless360]

There seems to be a few issues with Jumper at the moment so I'd go for FrSky..

[@Cristianxb]

@@Painless360 Issues like? I read about the Emergency Screen, but it has been solved. Any other I should be aware?

[@josephbove528]

Ever thought about Spektrum or Flysky? The Flysky i8 look really nice. My Jumper was defective right out of the box. Continuous static coming through the speaker. Seems fo be related to the screen.

[@josephbove528]

@@Cristianxb Continuous static coming through the speaker. This is what I got right out of the box. When the screen dims it just gets louder. Go for Flysky or Spektrum!

[@josephbove528]

@@Painless360 Spektrum and Flysky are nice options. My Jumper was defective out of the box.

[@patrickfrensdorff7485]

So cool radio, BUT!!! RECEIVERS??? Micros? Abilities with those receivers? How many channels? Etc

[@Painless360]

You've not watch my T16 series have you?... Check out the playlist, I cover how at the end of every video.. Happy flying!

[@javieruriel]

Where did you get it? I want to buy!!

[@MCsCreations]

Really nice radio, Lee! It really seems to be fantastic! 😃 I'm thinking about getting it for my father... But let's see. 😊

[@ralphyvazquez1471]

Thank you for your informative video it was great. I have the jumper t12 and I am trying to bind it to the lizard 95 can you show a video on how to bind the two

[@julianwhite1077]

Great to see it finally cracked open. I'd like to know if the spring loaded switch can be moved to the left side?

[@javieruriel]

Which receivers are suitable for this radio? Or which multi protocol device do I need?

[@Painless360]

It'll work with just about anything but I'd pop a 'real' FrSky JR bay module and use the x series receives..

[@primitivocruz]

I have a brand new $300 TBS Tango that I will be selling to get this Jumper; what do you think about that?

[@alasdair4161]

Great review Lee, I want one but might wait a bit for an internal module. There appears to be design elements included to take one, so down the road maybe.. It also looks as if we finally have a company making radio's that employs designers who actually fly RC... versus others who just copycat other players. It's a great step in the right direction for the hobby. Thanks for posting.

[@brianscutt6298]

Would your trust this radio on a 50cc and up aircraft ??

[@Painless360]

Not mine here. It's first generation and has a lot of quality issues. The later ones are much better now...

[@brianscutt6298]

I was thinking about buying one.

[@Painless360]

Check out the RadioMaster TX16s..

[@madforit9661]

So show me how you can add your own sound, eg voice track and assign it to a switch

[@Painless360]

Already done. Google something like 'Opentx sounds painless360' and you'll find it..

[@Phrancis5]

Will their future T20 look like the terminator?!! I've been using Flysky with the iRangeX module for years but looking at the jumpers for some time now. This one looks like the one to finally get.

[@robertpetrosky3067]

how do I donate Mr. 360

[@Painless360]

Hey Bob, links in the description. Patreons get extra early access, extra content, polls and support too.. thanks for considering it.. happy flying!

[@kevinmahoney9205]

This looks like a nice radio, but I just recently purchased a Taranis QX7 and can't justify buying another radio any time soon. What I'd really like to see in one of your videos is a comparison of multi-protocol modules and how to set them up in my QX7.

[@Painless360]

I've done the setup already - Google something like 'multiprotocol painless360 opentx' to find it..

[@kevinmahoney9205]

Thanks! I watched it and that was helpful. I'd still be interested in a comparison (if there's enough out there to compare).

[@SamStack]

You sure companion won't work? Jumper say to "update the firmware via OpenTX Companion software".

[@Painless360]

Using it to update the firmware is one thing, using it to create and manage model memories is something else entirety. Is there a Jumper T16 radio hardware profile in Companion? There is a reason that this isn't called OpenTX on this radio - see my other Jumper reviews for why ;) I will be trying in another video to see if it'll 'work with Companion on a X10 setting without buggering up the radio.. happy flying!

[@SamStack]

@@Painless360 Awesome thanks! I was all set to order one but not having companion would be a deal breaker for me.

[@sampsonguo8150]

@@Painless360 It can be flashed with X10 firmware, :-) Just LS/RS/S1/S2/T5 are inverted.

[@Painless360]

Cool! When did you try that?

[@sampsonguo8150]

@@Painless360 I have been using X10 firmware 5 days. Page button can't switch main screen after setting telemetry main view with Jumpertx firmware.

[@marukothekid]

Thanks!!! I'm getting one of these! One question though. Do you prefer iNav or Ardupilot? Why?

[@Painless360]

I've made a few videos on this topic. Here is the latest.. kzbin.info/www/bejne/qpaXdZKcn6eJnK8

[@GregoryBrown-fe5js]

What Rx can be used?

[@Painless360]

With the multiprotocol module, almost anything..

[@SM-cf7kv]

Beautiful video waiting the tbs video on it 👻

[@richardr3178]

I wonder if this radio is compatible with RadioLink? Great review!

[@Caroline_Tyler]

I can't check this from work but there is a companion section on the Jumper GitHub... Is that it? github.com/JumperXYZ/JumperTX/tree/2.2/companion

[@sjonjones4009]

I'm just now getting into the hobby and don't know the requirements for some features. Interesting specs for the processor: stm32f429bit6 www.st.com/content/ccc/resource/technical/document/datasheet/03/b4/b2/36/4c/72/49/29/DM00071990.pdf/files/DM00071990.pdf/jcr:content/translations/en.DM00071990.pdf If the specs are right then it *might* be DIY upgraded for: touchscreen 4k resolution screen (FPV screen?) more I/O 168 inputs (if you really need more- robotics?) I'm really hoping to upgrade to Halls gimbals if I get this radio. I need to research more before buying it.

[@FrugalFlyer]

Will it work with Futaba FAAST?

[@brownie6451]

I noticed you said it's not supported by OpenTx companion. Does that mean you couldn't get the Lua script needed to configure the SR6/8 recievers?

[@Painless360]

That's not a companion thing.. SXR and Crossfire scripts on the SD card..

[@brownie6451]

@@Painless360 So your saying the SD content you download from Open TX is compatible with this radio even though it's Jumper TX.

[@Painless360]

Comes with SD card already setup...

[@PropsOff]

Well, That's why my middle name should be "late". I just pored money in to upgrading my QX7 and have no more funds for this... However, I like what I see. Great review!

[@darrenfisher5838]

Hi could you please show how to put lua scripts on radio if you cant use companion on it also what do you use instead of companion Keep up the good work Regards daz

[@Painless360]

Cool, will do..

[@shozzy69]

Does any one one if this can work with hitec recievers they are afhds I think

[@mikebrown7366]

I believe the JP 4in1 module will work with that, but you should be able to check it out using Google.

[@ottokueng4236]

Good product, without Companion not usable for me. To complex Mixture for manual entry.

[@flimunki114]

As much as I like using my X9D it does feel like outdated technology, a colour screen with a decent resolution that can be read in daylight seems like the very least of an upgrade that the X9D could do with and if FRSky are going to rest on their laurels then credit to Jumper for bringing out a better spec'd transmitter at a very competitive price. Such a shame that they cannot take full advantage of the "open source" openTX, I hope they continue to develop their fork and who knows maybe even better what is being done in openTX. It does feel like FRSky have taken their eye off the ball and with the TBS Tango 2 on the horizon they may well find their grip of the market starting to slip!

[@ChrisBalmforth]

FRSky have already brought out their updated X9D - the X10. Same interface as this one, and it IS supported by OpenTX and Companion. I love mine, the only downside is the high price. Maybe FRSky will have to reduce this now to stay competitive?

[@flimunki114]

I don't really consider the X10 to be an updated X9D rather a new, higher end, model as it's almost twice the price of the X9D, not even Apple take the piss to that extent :)

[@ChrisBalmforth]

It depends how you differentiate between an upgrade and a new model! The X10 is functionally identical to the X9D, just in a new case with a nice colour display and high quality controls. Totally agree about the price!

[@Painless360]

I understand that the hardware for the X9D design was inherited by FrSky so its interesting that so many still consider it their best radio. Vendors who don't listen to the market and give customers what they want leave places for new vendors to take market share. Competition is good as it forces complacent vendors to step up their game with their products, or less usefully, sell their inferior tech at a much lower price point.. OpenTX shouldnt be an FrSky only OS and should be investing time making it easier to use and lowering the knowledge needed to use the system.. it'll be interesting year..

[@billsomrak]

Finally a Jumper TX that doesn't look/feel like a toy grade TX (sorry, but having had a Taranis X9D+ for 6 yrs. has spoiled me). I liked your video, but it definitely has an audio problem, where audio levels drop to nearly inaudible levels several times during the video .. at least, that's what I experienced here. That said, looks like this is one Jumper I could get behind .. but, already having a Taranis, I doubt that I'll 'take the plunge'. Cheers.

[@Painless360]

How odd, works fine for me here on PC and tablet, thanks for letting me know.

[@billsomrak]

@@Painless360 Hi Lee. I just went and listened to the entire video again. This time there were no audio drop outs. Strange. Maybe I kicked the sub-woofer under my computer stand and the connection went bad ... only thing I can come up with. All seems fine the 2nd time I listened to it. Now I'll have to be on the watch for a loose audio cable connection on my PC. Cheers!

[@mrb2917]

works fine for me too

[@upperechelon3456]

No audio issues here.

[@anybag7007]

I think they look like C3po after being smacked against a wall

[@filiped7298]

Thanks for the the review, Lee. The multi-protocol module says it supports Crossfire. Is that indeed true? So we don't need to buy that expensive TBS Crossfire module

[@jimhimesjr]

No, you’d need to buy the crossfire module separately. The multi basically does frsky, fly sky, spektrum and futaba.

[@filiped7298]

@@jimhimesjr ah ok. It knew it was too good to be true :-)

[@Mateyhv1]

Looks nice in that Futaba case. No turn off for the screen (means high battery consumption), side sliders seems easy to move inadvertenlty and worst of all, no Companion. Maybe not that bad for drones but for planes I use Companion a lot. No rush to change the X9D.

[@MrBumbles2]

ill wait a yr see how support goes ,, do like it need the extra channels ... frsky has a grip on the market see what happens , im sure there not happy. nice to see some decently priced products unlike hitec and futaba which i used for 40 yrs until recently . there great products just got tired of buying someone house . i have a few 1000 dollar tx that are useless and very limited. and there service well just buy another is there answer. maybe jumper will keep frsky from following the greedy little trail

[@ze3312]

Where can I buy this??

[@Painless360]

Lots of places are getting them in now, use Google to see who.. happy flying!

[@ze3312]

@@Painless360 every i look it is in backorder or out of stock...

[@mrb2917]

you'll have to wait then

[@mrfourtysevenman]

AVOID AVOID AVOID!

[@Painless360]

Why why why??? ;) thanks for leaving a comment but that's not useful at all. Why avoid?

[@stran92129]

jumper needs to work on their qc, reliability are horrid! frsky is so much better at this. cost affective is worth zero when i have 2 dead radio going on three, yet frsky i only have the one, and still working. make it more reliable and cheap and we got something. problems with reviews is they dont talked about the 6mths down the line. if they did it be a different review, might includes more swearing words. something a wise man once told me that comes to mind, " i am too poor to buy cheap stuff".. think about it.

[@bilalrak4432]

its very convincing what u said.. so much so that it makes you sound like u work for Frsky.. why u keep buying jumper when already two dead plus u got the one from Frsky that still works? and if u are getting replacements then why cry over money.. but then what do i know. i never owned a radio or flew anything