How to make your own wooden bed frame - Super King Size - DIY

Here's a real easy way to make your own bed base out of softwood timber.
This is a perfect solution to making the ideal bed base without spending hundreds of pounds.
In this project I am making a Super King Size bed, but this method can be used to make a single, small double, standard double, and King size bed.
You can do without the center slat support if you are going to make a single bed.
This DIY bed project is perfect for all skill levels, so whether you're a seasoned DIY enthusiast or just getting started, we've got you covered.
ESSENTIAL TOOLS
👉 Skill Saw: amzn.to/3Qbofvn
👉 Drill and Driver: amzn.to/3FbxYeT
👉 Tape Measure: amzn.to/3ZNZrgh
👉 Speed Square: amzn.to/3tjU0td
Below is the cutting list for the timber I used: (Super King Size)
4x posts 3"x3" x 375mm
2x top/bottom 2"x6" x 1825mm
2x sides 2"x6" x 2010mm
2x slat supports 2"x2" x 1900mm
1x slat support 2"x3" x 2010mm
16 slats 3"x1" x 1800mm
👉 Bed brackets from Amazon: amzn.to/36EimQo
MAKE A SMALL DONATION - Help me continue to make interesting content
paypal.me/just...
Thank you so much for your support
All tools used can be found at my Amazon Store: www.amazon.co....
MAKE A SMALL DONATION - Help me continue to make interesting content
paypal.me/just...
Thank you so much for your continuing support
CHECK ME OUT HERE:
Instagram: @jbpaintingdecoratingcarpentry
TikTok: @j.b.tv
Pinterest: @justinbailly74
Web: www.justinbailly.co.uk
CONTACT ME:
Email: [e-mail]
As an Amazon affiliate, I make a small commission on qualifying sales
#woodworking #diy #diywoodworkingprojects #superking #carpentry #diybed

[@brentward1831]

I have been thinking of doing something like this for a few days, and you crystallized EXACTLY how I envisioned it after all that thinking. Great job!!!

[@Aaron_Lindenberg]

Just built this for a full-size mattress and it's great!! Thanks for the amazing video! It felt amazing to be able to build this by myself and not have to go out and buy one.

[@georgianwindow]

Well done you

[@fontybits]

Suggestions: Make the legs high enough to enable you to use the large area under the bed for storage, e.g. suitcases, mother-in-law, etc. Also, cut out a rebate on the bottom of 2 legs, to allow the bed to be pushed up flush with the wall & avoid hitting the skirting board.

[@stephenbernard4675]

🤣🤣🤣🤣mother-in-law huh? Classic🤣

[@PrettyGreenMonk]

Last place id want her

[@lyndamarthaak]

Mother-in-law under the bed😮😂

[@carl8568]

You definitely don't want a bed pushed up flush with a wall. You want some airflow to discourage mould growth.

[@brianmagicman3556]

​@@carl8568What fucking mould grows in your house?? Mould is caused hy damp - not by a wooden bedframe Jesus fucking Christ

[@familyclemens986]

Thankyou, I have made this bed and it's awesome. Extended the legs and made a headboard. Couldn't have done it without your video. 'It's Friday night and I'm having a beer' is now a standard quote in our house.

[@mariavako]

Loving the option to disassemble and reassemble, mainly because people move, and it's far easier to move this heavy thing more quickly and safely. Thanks!!!

[@rolandorivas9119]

Hello My British Amigo!! I am a Latin man living in Canadá!!! I watched some other videos on KZbin how to build the best and easiest bed frame. I was about to give up with someone else's design when your video came up!! I AM SO HAPPY!! I watched yours 'cause is THE BEST!!! my friend !! The easiest to put together and and take apart for moving purposes. Pretty looking clean frame and must have for sure nice aroma too. I don't like to copy-cat 100%, but pretty close..I will just make one small change in the little piece of wood that goes in the center from front and bottom of 2"×6" to hold/support the 2"×3" timber that hold the slots across. Congratulations I give you 100% ☺️👊👍Muchas Gracias🙏..Hasta Vista🙋AMIGO..!!SALUTES desde Alberta, Canadá

[@D3cyTH3r]

Hi Rolando, did you make this bed in the end? If so, could I ask what change you made to the little piece of wood? I feel like that is the only week spot in this design. It's basically a 1" strip of wood holding the 2"x3" (it's only as strong as it's weakest spot, and the screw is going to doing be most of the work).

[@littlesarahautism9787]

I can't thank you enough, you kept it basic simple and straight to the point I've watch over 20 videos and I've gotten an instant headache just watching them. I love this bed I can't wait to get started. . Thank you again, new subscribe.

[@JBTV]

Bless you 🙏

[@James-ye7rp]

That is absolutely wonderful. Thanks. My wife just walked in and saw that, and guess what my next project is?

[@firestar7774]

I am giving my other half his new project. He doesn’t know about it yet 😃

[@gregvglover4476]

This is the best king frame design that I’ve seen. Sleek modern lines. Simple and elegant construction. Great work!

[@JBTV]

Thanks Greg Greg

[@brianmagicman3556]

​@@eliteonly5344Cardboard, dartboard, chess board, bread board

[@maheendrannair9557]

I have watched many videos on DIY bed for a similar bed frame. I am fully satisfied with the design,it's making and the mode of presentation. One of the best designs I found in internet. Thanks for the simplest design. Nice job well done.

[@annieholbrook2852]

Hi Justin, Just to say we followed your video, and have completed our double bed. Our local wood supplier was most helpful, when we told him what we were attempting. We chose to make the (head end) legs higher, at 39” (100mm), and the foot legs 20”(50mm). The upper legs we have included to horizontal bars, thus giving us a headboard. Comments so far have been positive, we tell them it was from your site. 👍👍👍👍

[@gailjohnson3544]

Any pictures

[@alexbalfour6041]

I’m another ‘bloke’ who likes to do his own stuff at home. I have to say, not only is this a fantastically helpful clip but you seem like a top man to boot. Thank you for your wisdom!

[@JBTV]

Thanks for the nice message

[@whomadethatsaltysoup]

Absolutely fabulous! I'm on making one for myself. The old divan has given up the ghost, and I'm not about to part with the thick end of a grand for a wobbly, squeeky, particle board contraption. Not when I can easily put one together that will be rock solid, and at a fraction of the price. I've already watched a few YT tuts on how to make your own bed, and this is by far the most straight forward. Thanks for sharing. I'm on the lookout for the headboard upgrade.

[@JBTV]

Brilliant, thank you, and glad this helped. I have a headboard video too!

[@LITHIUMINWATER]

I am going to scale it down for my dogs bed, fencing two of the four sides. This is a beautiful, simple, sturdy design. Thanks a lot!

[@robert51045]

Design engineer and many years ago taught joinery and cabinet making. This is by far the best instructional video I have ever come across.

[@f1bomb]

This is exactly what I wanted but I wasn’t sure how to build it but now I do!

[@MargoKruczek]

This video gave me the courage I needed to start wooden frame of the bed. Thank you.

[@traceurernest2222]

I didnt even think about using hardware for the bed frame, usually all the videos that pop up are all joinery techniques that take a long time to prepare. This makes it much easier for people without the proper shop. Also liked the beer scene in it lol

[@michaelocallaghan3025]

we just built ours fallowing along. first proper bit of furniture we've ever built. cheers :)

[@Lostadvent]

Wow the hook like brackets are really smart holy buckets!

[@jay-co2vq]

Quick , Simple & clean, most importantly , you are able to disassemble it, I'm going to make it with some slight alteration particularly taller legs for the headboard. Great video .

[@cathylindsay7576]

Thank you. I am going to make this bed frame. I've been looking at building plans and I like yours the best !!

[@EEX97623]

Had this tutorial video and cut list tucked away for a few months. Just completed the bed frame build for EU king size, as per all the spec. It’s a solid beautiful bed frame! Plugged feet post counter sink holes, added a salvaged piece of maple as a headboard. Thanks so much Justin🍻

[@JBTV]

Great stuff, really good to hear 👏

[@Falconurbex]

Ur matress looks nice amd thick do u mimd me asking what sort of matress it is ie posterapedic or memery foam etc great build btw thanks for the step by steo unstructions im going to build my own now so a massive thank you.

[@JBTV]

Thank you so much. The mattress is a gel filled climate control type. Cooler in the summer, and warmer in the winter, it's very very comfy. Good luck with the build 👍

[@moody1981]

Excellent job, simple and easy

[@jjalandoon]

Awesome! You design some parts to be removable, but those plugs will make it permanent

[@JBTV]

True, but the top and bottom sections are relatively small

[@ronaldharris5562]

You did a great job!!! I love how you plugged the screw heads and chiseled it flush. Could tell there was ever a hole

[@JBTV]

Thanks man. Close up you can see the plugs, but very unnoticeable from a small distance.

[@alexc6293]

Hi mate, Thanks for your video, its just what I've been looking for. I think I'm going to use a slight variation on your design. I have a few questions that I hope you can answer for me. How has your design held up over time? Is it still solid? What type of wood did you use? I've seen some comments on websites I've looked at saying to use only hardwood. From what I've seen it looks like its OK if big enough pieces are used. I want to make it taller for more storage underneath. Do you think the type of wood and joins will be strong enough with added height? I guess they'll have more leverage on them. I think I'll just incorporate the headboard into the legs at the head by extending the legs up. Do you see any problem with this? Can you recommend anywhere that sells cut and finished wood? I live in an apartment so if I could just get the specification of wood I want delivered, pre-cut and finished it would make things easier. I have a tool library near me so I can get the tools I need if I cant find a place to do those bits for me. Cheers, Alex

[@alexc6293]

By finished I mean prepared

[@danjo2253]

Nice job man! That frame looks absolutely strong and sturdy, just what I need! Now ..... I need you to build one for me!? Great video! ThanQ

[@JBTV]

Thanks Man, appreciate it.

[@GodsVibes]

Magic, I will be starting a single bed next week - Really enjoyed your video, bed looks Great

[@jared7211]

Thanks for the great idea. I was thinking about buying a wood bed frame but I never thought about building my own.

[@owenbooth6891]

Am planing building my own bed and I only though this was the way to do it good job 👍

[@dengueberries]

Did you predrill the holes for the brackets before screwing them in? I can't see if you did. I have a much lower quality combi drill and am worried I won't make it through but also I find sometimes when I pre-drill it doesn't get completely straight. Thank you for your help. Thank you

[@JBTV]

Yes, ALL holes were pre drilled. Good luck 👍

[@maximusstar9960]

Well done Justin...clearly the best on KZbin DIY

[@JBTV]

Thank you 🙏

[@Mr69souprman]

Down sizing and Using this plan for my grandbaby bed for our house for her visit ❤

[@sunilkumarpvasudevan]

Thank you! The first time I saw a video where one can make a bedframe by themselves, without spending on costly machinery :) which is normally the case...

[@dgibson2314]

Thank you. This is exactly what I was looking for , Justin. Job well done.

[@dengueberries]

Do you think two 6x120 mm screws through the 3x3 legs into the top and bottom would be OK? I have modified your instructions to instead use 2x4 so now I have to basically fit the 6x120mm screws in between the 4x40mm screws of the bed brackets, but the margins between the middle two screws is so small. I am making a smaller bed though, at 140x190. Thank vou very much in advance.

[@jessicaking-fv2yv]

where would you suggest getting the wood from and do you have a rough cost breakdown ? is there a stark difference in building yourself and buying a new one ?

[@jlr1487]

Nicely done ! Simple clean lines, great detailed execution. Good work man !👍 I do have question if you don't mind: did you consider adding a center post to help prevent sagging/improve solidity ?

[@juanlopez0808]

Good work, I like the corner hooks for future undoing/moving

[@Marcel-ju2gy]

It's a great build with basic tools I would love to see a build of a rectangular bed-end Ottoman for this bed.

[@soukiallen1]

i have research all kinds of home made bed frames this is the nicest one i have seen and planing to approach my bed frame project like yours thank you....

[@andyczech117]

Not too bad... When i was doing mine i decided that the best way of fixing all together is to use bolts and nuts not a screws. And also for this such a size of the bed it's stronger to let the side and front panels lying on the legs... Just my suggestion...

[@maya7376]

I just built this. I totally agree. The hinges I should have put on the corner posts. Currently the feels a little rocky. Although I think I need to reduce my height. I’m also going to secure it with L-brackets. Otherwise feels quite sturdy

[@romeorice583]

Maybe in the UK that’s a super king sized bed, but I can assure you that’s a Queen sized bed. Nice frame either way

[@suequinn4212]

I'm in Australia and that bed is bigger than our Queen. Our Queen is 1500mm wide, SK is apparently 1800mm wide. Our Queen size is the same as their King size, not Super King size tho

[@jasonkaminski6230]

Simple clean design & good info

[@galemaynard6665]

Hey thanks I like the way you build it I will build one for my wife.

[@michaelaburt1195]

Nice! I think this will be the template for the frame I plan to build next month! Thanks!

[@jmtfishing450]

This is great, learning from you is awesome, and what's good is that, now you can actually make your own king size bed. Cheers and can't wait to see your next videos.

[@JBTV]

Thanks very much Tawita 👍

[@seanorourke8470]

Class,the thing I bought was rubbish,nice Job

[@cachibachi5037]

I’m about to buy some timber and make one myself. Great video

[@susanjeffay3851]

This was the best video! I looked at every KZbin for a bed that I can make and take apart when I don't need it in the mini school bus we have. Your explanation is the easiest for me to understand and Ive ordered those brackets from Amazon too, as I once had a bed with them- totally fits my need!

[@JBTV]

Brilliant! Thanks Susan, glad it helped 😁

[@ChrisS-bq4pj]

You mention that you measured the bed beforehand. What is the width of the front and end woodbeams in cm? Is it 180cm? Or is it more? What is your Marge

[@majambomajeed6887]

Thank u .for doing this project learnt so much .very basic but learnt so much .it was brilliant .you could be a very good teacher in joinery .thank u again

[@JBTV]

Thank you so much

[@majambomajeed6887]

@JBTV thank u .and reward u with this world and everything in it.god bless u and you're family .thank u for all you're hard work

[@ahmedelnezamy6361]

You made it so easy thanks

[@JBTV]

Thank you 😁

[@jamieryderofficial4171]

Love the video very helpful 🎉 what are the brackets called

[@JBTV]

I'm not sure exactly, but search bed brackets and they'll soon come up

[@theacase8738]

Excellent demonstration with detailed instruction. I am thinking of using this tutorial to make an elevated dog bed so my dog can look out the window.

[@nissarahmed8064]

Great carpentry. Well done.

[@JBTV]

@@nissarahmed8064 Thank you

[@Gstonesheat]

Best one I have seen yet, thanks for sharing this bed frame idea 👍

[@ningis21]

Nice little job...How much did it cost in the end? Fabric under slats is the way to go if you intend to move....easy dismantle and roll up...and a spacer block at each corner to secure...(think spindle spacing on stairs). Don't have to many beers....and now.... let the testing begin...ha

[@TrixyLixyStix]

Hi, couple of questions. Did you end up screwing all the slats? Does this build actually squeak when you sleep on the bed? And did you get the wood supplier to plane the timber or did you just buy it off the shelf and sand it yourself? Ok tjat was more than a couple of questions. Cheeky last question, how would you have done it if you wanted the legs to be central to the sides and ends?

[@anoshya]

Very good presentation..simple to follow..thanks

[@kabelutshilama6385]

Very smart Job that you've done Justin.

[@JBTV]

Thank you

[@handarchitecture7709]

I built this bed. It turned out great but I did add a couple elements. I added heavy-duty corner braces and spacers for the slats. I like to turn my mattress now and then and don’t want the slats to move.

[@gallowsongs]

quick question, did you buy as PAR? It's quite costly, I'm coming up at around £450 inc. VAT. the most expensive is the slats - I've worked out that I need 20 to achieve a ~31mm gap (50mm is the most recommend buy the mattress manufacturer) so this is 36m of slats! Trying to figure out how I can reduce costs. I'm also wondering is aesthetically I would want to deeper on the long boards, that would allow the centre support to be integrated easier. Also considering a tendon/mortice joint for the sides, and using the brackets for the heads/ends (just want to make sure the bed is sturdy in that direction 😜) Thoughts?

[@garvielloken3929]

Brilliant!!! Looks SOLID. Nice one JB!

[@TheAmazona67]

With the slats, you could permanently fix wood spacers along the rails. That would keep the slats from moving around too much.

[@khalidali4364]

Lovely bed

[@chrisboyd4433]

That was my idea. then the slats can just sit in place and it would be easier to break down for a move.

[@warkarma]

How are you planning to disassemble it later on? Since you glued all the holes for the screws :)

[@tommycollier9172]

Very nice job and beer breaks are essential

[@dcrtse]

The best part of this video was the mandated beer break. Cheers, mate!

[@emmaauty2922]

This is good timing. With a little one who comes in and out of our bed when he struggles to sleep (teething!). We’re looking at super king! Would love to save some money if we can!

[@garryn123]

nice job. im thinking of adapting ur design to use IKEA slats. you could staple some 'tape' between the fixed slats to prevent non fixed ones from moving too much .

[@EMNM22]

5:50 I hope you meant "when you assemble it"..... 🤔 LOL!!!!! I really love the simpicity of your design. 🤘😁

[@leonlion6713]

Very Clever and very Good Quality 👍

[@everardoayala5978]

LOVE-IT. I will try it really soon and come back with my results!

[@isauraaortiz]

Wow Exelent Work Done. Thank you for sharing ⭐️⭐️⭐️⭐️⭐️Love it! ❤️

[@lakshmanpussegoda9767]

Do you think a 'affodable' hard wood like poplar would be worth the extra material cost? Thanks for the detailed instructions and not rushing through it, etc.

[@JBTV]

It sounds like a nice idea, but probably not entirely neccessary

[@daviddavis6065]

brillent job what a cool bed

[@jblflatpicker]

Two thoughts: 1) all that weight being supported is dependent upon the sheer strength of the screws. Screws are not great for sheer strength. 2) all of that wood hanging past the mattress, especially the corners, is bothersome to me. Especially when considering getting in and out of the bed. I’m looking to build my own king-size frame and those were the only issues I would have, personally. Otherwise, I think it’s an excellent build!

[@kabeerjain11]

very nice, skillful

[@ChrisS-bq4pj]

I am curious whether the bed hardware that you installed are strong enough and that they last over time?

[@JBTV]

Well I think it's nearly 3 years on, moved it 2 or 3 times, taken some beating, all good 👍

[@williamtickle9679]

Would it be possible to place dowels in the rails and holes at the end of the slats? That way you could let the slats float and it would be possible to disassemble the bed and move it.

[@oscarmoht]

I stumbled on this video after almost giving up , just about to make a bed for my daughter and this is the best video here. Thank you so much.

[@salmanzaheer5060]

So helpful video. Thanks for guiding 👍🏻👍🏻👍🏻

[@amithyel]

Could be this frame use to build a loft/high sleepers bed? The legs obviously much higher and with extra support and stability - install another timer around 60-90cm from the floor. Could be enough strong and stable?

[@JBTV]

There's no reason why not, with plenty of support 👍

[@adriansteer4377]

Easily the best plan and tutorial for a bed I have come across. Love the simplicity and is just what i'm looking for. Couple of quick questions if I may: 1. Could you use pocket screws when screwing the rails into the posts instead of screwing into end grain? 2. Is it just a simple matter of making the legs longer if i want the bed higher to store stuff underneath? Thanks heaps

[@JBTV]

Thanks man 😀 You could use pocket screws, but it just wouldn't bite into the timber as deep. Perhaps throw a couple of big dowels in there too..!?

[@JBTV]

Just consider, the taller the bed, the deeper the skirt needs to be for stability and rigidity.

[@gerardoconnor2699]

Cool mate, loved it

[@Kingbluemena]

Would it be okay if I painted it black? Or would it ruin the wood?

[@Ramndom]

What wood did you use? Is it prone to bending in a humid environment?

[@JBTV]

Standard pine. The bedroom isn't humid, and the timber hasn't bent or warped after all this time 💪

[@Ramndom]

@@JBTV thanks. Going to try it. If I succeed I will let you know 😂

[@heathersullivan8833]

Great video, just what I needed to see, thank you

[@lawrencedavidson6195]

Very nice construction. I will be making a bedframe soon, although not quite as big. I found your video very useful. Greetings from sunny Jamaica.

[@jusseleanor8435]

Hello I'm going to be attempting this from your video and was just wounder what wood you used? I don't know much about wood other than oak is strong haha so what wood did you use in this video? Thank you

[@isauraaortiz]

I needed one Queen size Beauful! ❤️

[@MM-oq1lb]

Wonderful! And he is doing yoga too while at it:)

[@mauricelee7299]

I am so going to build this bed!! Awesome work.

[@danielwrekly3921]

Nice job will make me one i will use 2 by 4 joist braket and instead of slats use plywood

[@harmonsalmon7739]

Beautiful finish,i will make one myself.

[@dingshangliu2521]

精彩的视频！，虽然我听不懂英文的解说，但制作步骤对于我来说是非常有帮助的！。感谢分享！

[@dunsmoregaines4239]

Are you using those flat ended, threaded heavy duty wood-use “carriage bolts” for the attaching of 3x3 posts to 2x4 length and width of bed lumber and the center piece cutouts in the middle on each end that hold the center piece? They usually come in 3/8 and 1/4 thickness and a range of lengths, like 2,4,6 inches long. They’re called carriage or carrier bolts in the states.

[@JBTV]

Yes I am 👍

[@dunsmoregaines4239]

@@JBTV Thanks!

[@pennstater89ad]

Awesome job Mate!! I got a question, how far down are top of the support slats from the top of the frame, 1 inch, 2 inches? I'm wondering how much depth the foam mattress needs to sit in the frame to keep from sliding?? I'm building a twin size wooden bed frame.