Hey do you have any idea how to change the oil coolant hose that runs on the side of the motor near the timing chain? the long hose not the not U shaped line that bends, there seems to be little to no clearance to remove old hose and install the new one.. any tips appreciated thanks
@wisin_k20Ай бұрын
@@dannyem4787 what I ended up doing with my civic was that I used a long niddle nose pliers and a long flat head screwdriver to help me pry it off once you slide off the clamp grip the hose with the pliers where the clap was and wiggle it right to left to break it free it probably been on there for years and it’s stuck.
@wuzT4027 күн бұрын
3:42 Quick question: Can you run this on Acura tsx K24A2 to keep my oil temperature cooler?
@wisin_k2027 күн бұрын
@@wuzT40 yea that’s what its supposed to do but it’s a small oil cooler , if you want a performance oil cooler that’s gonna help bring temps down better.
@joseraya89987 ай бұрын
Might sound like a dumb question. But which of the two hoses has oil running through them ? (Connecting to oil cooler) Both or none ?(only coolant ?)
@wisin_k207 ай бұрын
It’s only coolant
@joseraya89987 ай бұрын
Got it! Thanks Also replacing gasket and hoses on oil cooler , I would have to flush both oil and coolant?
@wisin_k207 ай бұрын
@@joseraya8998 yea. I would just add new oil and coolant.
@Daniel-i2g3t5 ай бұрын
Can coolant get into the oil if the oil cooler is broken?
@wisin_k205 ай бұрын
@@Daniel-i2g3t it might be possible I’m not 100 % certain but it could possibly happen if it is damaged.
@alwx_.2 ай бұрын
Hey so I’m getting a leak from the oil cooler it’s like repetitive drops of coolant I checked the gasket and it’s in perfect conditions what can it be?
@wisin_k202 ай бұрын
@@alwx_. if you replaced the gasket with a brand new one try adding a little bit of Honda bond to it so it help to seal it and to keep it in place and it don’t come off the grove when you are putting the oil cooler onto the block some times it will come off the groove with out you noticing and pinch the gasket and create a leak. Just add Honda bond to the groove then put the gasket on top of the Honda bond so it doesn’t fall off.
@wisin_k202 ай бұрын
@@alwx_. also make sure you torque it to 54 ft lbs.
@alwx_.2 ай бұрын
@@wisin_k20 haha yeah I tried that I even tried putting hondabond on the rim of oil cooler and it was still leaking
@wisin_k202 ай бұрын
@@alwx_. damn I’m sorry to hear that. Don’t know what else to have you check without being there personally.
@alwx_.2 ай бұрын
@@wisin_k20 haha yeah im just going to delete it for the meantime until I go turbo on my other k-series I’m building on the side
@jzur499 ай бұрын
What socket size did you use for the center bolt? And do you know if it's the same size for a 93 accord se?
@wisin_k208 ай бұрын
I used a 30mm socket. Not sure on the accords.
@glenglene84737 ай бұрын
how did you remove the threaded sleeve where the oil filter screw onto? If I use the vice grip, I will destroy it.
@wisin_k207 ай бұрын
I use vise grip it’s not on there tight at all.
@Hello_its_me_mario Жыл бұрын
How did you remove the oil filter stud off the k24?
@wisin_k20 Жыл бұрын
I just grabbed it with vise grip’s and twisted it off it’s not on there that tight.
@yenielyLopez7 ай бұрын
My k24 is leaking antifreeze out of the oil cooler you can it be a bad gasket?
@wisin_k207 ай бұрын
Have you checked the 2 hoses? The coolant runs through there.
@yenielyLopez7 ай бұрын
@@wisin_k20 yea there tight it’s just weird cuz I never had an issue with that so idk if it’s the gasket cuz it’s pissing out
@wisin_k207 ай бұрын
@@yenielyLopez I would inspect the hoses really good make sure it doesn’t have any hair line cracks cause under pressure them hoses would expand and make them leak. Are they leaking all the time or only after you drive and then park the car?
@wisin_k207 ай бұрын
@@yenielyLopez I don’t think it would be the gasket because I believe it’s oil that circulates through there.
@wisin_k207 ай бұрын
@@yenielyLopez well if it’s coming from where the oil cooler joins with the block then change the gasket cause that’s the only thing in between there. K24 don’t come with oil coolers from factory unless it’s the newer SI MODEL K24 I believe so if you installed the oil cooler it is possible that the gasket could’ve gotten pinched and not sealed properly. If you do go ahead and change the gasket go ahead and put some Honda bond on the gasket so it stocked to the oil cooler so it doesn’t fall off the cooler when you go to install it. GOOD LUCK.