Honda Civic Si K20 to K24a SWAP DIY (2006 2011 Si)

[@559powerscape]

Good Job Gerb! You did a great job on that swap!

[@dominiksamir6763]

dont know if you guys cares but if you're stoned like me during the covid times then you can watch all the latest movies on InstaFlixxer. I've been streaming with my brother for the last couple of months :)

Good video brother.. Very informative for a lot of people to not just hear, but see all the sensors and parts that are needed and have to switched over.

[@kevinharris-charles4066]

Hey Gerb, don't get rid of the K20. Keep it for a future build buddy.

[@ratedr2372]

He should do a head swap with the k20!!

[@JR_Subie02]

Hey gerb thanks for all your video just finished my k24a swap and running like a champ. I haven't gotten the flashpro but it's running like it should. That's for ur videos.

[@TheGerbsteve]

Np man, thanks for all your support 🙏🏼

[@LeandroGomes-sw3jz]

Hii José, you are running the k24 on a civic Si not tunne?is running good and strong? I gonna make this swap i have a 2007 Si coupe, i dont have the money for the flash pro only for the k24 engine.. 🙂

[@JR_Subie02]

@@LeandroGomes-sw3jz yeah Its been running good. Am saving up money for flash pro but haven't tuned it yet. It's been 11 month

[@JR_Subie02]

And it still running strong

[@BjYeager420]

I just bought a 2007 si and has a bad k20. After watching this video I'm definitely buying the k24 it's cheaper then what I can find a k20 for.

[@cheesehandles]

dude, literally bought mine a week ago and mine blew on the drive home 😂 good luck brother, i know we both need it 😂🙏

[@BjYeager420]

@Gabriel Villalobos bought what a k24 and swapped it. Or a civic with the k20 and it blew?

[@cheesehandles]

@@BjYeager420 bought an si and it blew 😂 probably gonna go back to k20

[@BjYeager420]

@@cheesehandles k24 is cheaper

[@taronate]

same here, i'm 2200 miles in and my mechanic found metal shavings in my oil and before that i thought i had a timing chain/tensioner issue due to my p1009 code

[@fruitydudexD]

You are a godsend I bought a jdm k24a not knowing about the water pump housing so I was about to lose it trying to figure out the pulley situation. Your video is very informative, thank you so much

[@TheGerbsteve]

Glad I could help

[@cesarz188]

My current project right now, thank you for the advice , def very helpful. I got k24A RBB motor recently after my k20z3 made it to 230k miles before head gasket blew.

[@DiyFg2]

This is really really good info. I just keep watching this over n over. Thank you dude.

[@diegomendoza5096]

Hmo K24a comes in tomorrow for me. Very helpful video answered a lot of my questions thank you Gerb 👍

[@TheGerbsteve]

HMO is the shit! I’ve heard nothing but great reviews about them. Glad I can help you out. Now go do your swap 🤣🙏🏼

[@jmejia2979]

This was actually very helpful. I'm currently looking to give new life to my 8th gen Si.

[@TheGerbsteve]

Glad it helped you out. Not a lot of vids out there, so I figured why not make a series

[@apehouseprezahg6665]

The most helpful video ever. Thank you so much bc im doing the exact same thing rn. Awesome help

[@TheGerbsteve]

Glad I can help you out 🙏🏼

[@ChrisHondaProductions]

Luv this vid my favorite line is learn something through a lens ! Thanks for the info bro !!! Share the knowledge!!

[@TheGerbsteve]

More to come eventually

[@mikellewis2346]

This was a very helpful video. I'm looking at buying a 07 si with k24a swope done allready.

[@julianperez1270]

I just did a k24A swap on my 8th Gen just waiting on Flashpro. But the only sensor you have to change is the Crank sensor and the Vtec sensor behind the engine. Everything else just plug in and you can use the K24A crank pulley and need k20z3 oil pan and CRV post mount..but Everything else is direct plug in. All I'm waiting is for my Flashpro which is coming tomorrow brand new Bluetooth.

[@johanfeli2044]

So nothing need to be transfer just a few things

[@matthews.9794]

Overheated my 06 si doing a k24 swap thanks for the vid really helpful

[@TheGerbsteve]

Glad I could help

[@crismgaming4379]

the fact you have this guide is amazing great video

[@TheGerbsteve]

Thanks man.. wait until it’s time to turbo

[@evan_n6136]

gotta admire the gerb, this guy has been goin at it day in day out. nice vid man. i used to have built k20z3 head/stock k24a2 block 8th gen sedan

[@andrewbrown1344]

evan_n I am currently doing this to my 8th gen coupe!

[@TheGerbsteve]

Appreciate the kind words and I’m glad you see the hustle 🙏🏼.

[@briggsbaskin1638]

My k24a coils worked in my z3 just an fyi for anyone wondering they are interchangeable

[@SeanGarcia-ms3cj]

Thanks for this video, in the middle of doing my engine swap and im doing full k24 with the z3 oil pan. Sorry about midnight I hope your next project works out well

[@TheGerbsteve]

Thanks for the support! It is time to focus on the clean fg2

[@DasilvaOGG]

Gerb thank you so much for making these videos You’ve helped so much couldn’t thank you enough 💪🏽💪🏽💪🏽💪🏽💪🏽

[@lamesamelame]

Thanks for this video. I'm planning on finding a 06 -11 Civic Si and doing this swap.

[@bobbydelamar606]

Build looks nice! I'm doing wiring on my K24 CRX.

[@TheGerbsteve]

Good stuff… I want an older Honda chassis

[@bobbydelamar606]

@@TheGerbsteve kzbin.info/www/bejne/oISXoqqLm7KDiNk Kind of an older video of mine. She's a lot further along. I just need exhaust and some various hoses or problems that I'm sure will arise 😆

[@humbleservant4724]

Yesss I’m finally going k24a2 on my fg2😭🙌

[@DrivenbyfaithAutomotive]

This is fire 🔥, me and my 14 year old son are getting ready to do this swap

[@TheGerbsteve]

You guys are going to kill it 🤙🏼🙏🏼

[@aaronmoura1158]

Hey gerb gonna do a 2004 k24a swap to my 08 si Civic 2dr and this vid really helped

[@TheGerbsteve]

It is a very rewarding swap! Best of luck

[@aaronmoura1158]

Thanks brother ! Down here in ma been watching you for a min seen you around providence a couple times to loll but quick question you didn’t have to change your Ecu right ?

[@MultiChimRichalds]

You got to put that k20 head on the k24. Huge power gains

[@TheGerbsteve]

I am going to in the near future bro 🤙🏼

[@Funk210]

Great video man! Trying to build my confidence to do the swap. Im ready to hit the buy it now option. Only thing stopping me is having my daily down for a couple days. My base rsx really needs a pick me up. Ive got fbo and ktuner. Have everything to do the swap except the swap itself. Real nail biter. Great videos tho!

[@TheGerbsteve]

Go for it, it's not too bad. I know the feeling, I need to buy a new daily. The k24 in the rsx will be worth it, trust me. good luck

[@glenglene8473]

May I ask where did you get your base map?

[@1magicmungia]

Appreciate the help! super familiar with B series and just got k series. I have a k20a2 thats just head to pan. Also have a element and was wondering how much stuff i could take from the k24 over to k20. This video helped. Thanks

[@Jeremy-io4hm]

I love your videos bro. Thanks for the content.

[@Hatsukemi]

Nice job! i want swap my usual civic FD7 whith R18A2 to K24A3. Salute from Russia.

[@jon18schmidt]

Thanks for the video literally about to do this

[@chriscvgg3611]

You can run the car with out the oil cooler just get the tsx water pump ,, for those on 2024 make swap 💯

[@sethking3]

Dude, in the beginning I thought you were reaching for a Faygo orange. That's my fav orange pop. ✌

[@kridicalxsi1177]

Might hit you up when I get closer to to doing mine. Built k24 is definitely next.

[@dead_slide]

The vtec solenoid from k24 only has 1 plug cause the jdm motor doesn't use an oil pressure switch for vtec iirc. A usdm k24 would have both plugs I think.

[@mach389]

My thoughts exactly.. great video 11:03

[@TheGerbsteve]

🙏🏼

[@bradwysong4254]

I swapped my k20z3 to a K24A and it ran on its own for 15 or so seconds and cut the engine cut out now it won't start. Fuel is coming out of the fuel line and the engine has healthy compression on all four cylinders. I need to do a spark test. I was wondering if you encountered any of these issues. P.S. you're videos were a huge help when I was debating if I was going to perform the swap.

[@henrivillegas8050]

Thanks for the info bro really helped me out

[@adamuberschaffenheiser8501]

Good video my k24a2 has most of the questions answered. But for the computer..... No idea.

[@Gxthica]

Thanks for the video about to do this now

[@AlexWaters-i8b]

Does the k24 oil pick up unit fit in the z3 pan correctly or does the z3 oil pickup need to go into the k24 with the z3 pan

[@TheGerbsteve]

@@AlexWaters-i8b k24 fits into z3 pan

[@coolymanh9305]

What year crv post mount will I be needing?

[@DavidTheCarGuy8]

04-08

[@ItzzLex]

thanks bro pulling motor like my 3rd time thinking about k24 soon not sure yet tho

[@TheGerbsteve]

Go k24

[@ethanbunch1142]

hey man do you have to swap the oil pump to fit the pan or does it work fine?

[@tazimali1650]

Hey Gerb I am helping my friend with a K2.4 swap on an Acura CSX 2010 same as the civic 2010 can we pull the engine & transmission from the top rather than taking the subframe from the bottom & removing it from under the car

[@dafb6dafb62]

My boi keep doing your thing very good video 💯🙏😎perfect info

[@evan_n6136]

Also, ABSOLUTELY throw that z3 oil cooler on if you're doing that swap!

[@NguyenKevin15]

Wouldn't I need a new ecu and wiring harness or a retuned?

[@BassheadDemo]

I bought NGk coil pack from TSX u think they will fit on 8th gen civic si plug wiring harness the part number changes 48699 and k20z3 NGk coil pack part number is 48922

[@EhDerek]

You give me inspiration

[@scoped4k915]

do you have to buy flashpro for the tsx or can you use the one for the fg2 once k24 swap?

[@danielvidales8630]

Hello, what oil bayonet did you use? Does the oil level stay the same?

[@tylerskates4moms]

Called a dipstick, keep the k24 oil dipstick

[@johnrosario5273]

What year in specific for the crv post mount

[@BAKEN-420]

Hey I was just wondering with the side motor mount you need a 2002 to 2006 CRV post mount but what else do you need do you need the whole motor mount assembly from the CRV or just the post mount

[@EduardoGonzalez-hx8ee]

Hey Gerb I have a question. does the factory ecu of the fg2 work with the k24a or is the FlashPro a must for it to be drivable?

[@danielvidales8630]

Hello! How many liters of oil did you use with z3 oil pan?

[@keithgaboy3067]

How do you deal with the immobizer

[@johnnyquinones1380]

I recently bought a fa5 with a k24A and I want to change the spark plugs but idk what car to buy them for, can you help me out? Thanks!

[@Luigi-007]

I am looking to do the same on a 07 civic si. Its hard to find another z3 since my brother spun the rods so im looking for the k24a. Could i use the same ECU and transmission from the k20?

[@TheGerbsteve]

Pier B nice man. It definitely is hard to find a clean z3 engine. If you do find a nicer k20z3, you’ll be paying top dollar for it too! Yup, you can run k24 off of k20 ecu and tranny

[@Luigi-007]

Gerb I appreciate that man! One mor thing, the k24 redline stops at 7 and k24 at 8. How do you go about that? 7 would be my new top?

[@Luigi-007]

Gerb How does that work about the 7 top rpm on the new k24. Thanks man

[@lifeschoice6235]

what did u use to remove the k24a oilt filter thread bolt?

[@tazimali1650]

I read the that you can pin it to about 45 degree I am in Canada do you know if that can be done and is it safe to do so

[@thatblue_fa5448]

In the middle of doing my swap, and I noticed that the k24a block has studs for the oil pan. How did you remove this?? I didn’t see it in the video and I’m stuck now as to how to remove it safely

[@rodroguez909]

What year of crv did u get that post mount bracket off of

[@WexfordGamingNetwork]

Do i have to change the mounts or mount locations at all?

[@tazimali1650]

My Acura CSX engine blew up I bought the tax K2.4A2 engine it is a little taller (19 mm / 0.748inches)than the k2.0 can I use the TSX intake& exhaust manifolds & would it fit

[@tazimali1650]

Hey Ferb my car is a daily driven all that is available now is the TSX K2.4A2 the guy it would fit I saw you swap all the sensors just wanted to know could I use the TSX intake and exhaust manifolds

[@elijahsouthern144]

I recently bought a civic that had the k24a2 swap. It has the skunk 2 headers on it but slap the firewall hard. what did you do for the clearance issues?

[@joset2235]

he put spacers on the rear lower mount t😁

[@joset2235]

basically let’s the engine move forward up with the spacers and let’s the header clear better

[@Fudgiedahboss]

What axles did you used on k24?

[@victorwilks88]

Cant wait for the comparison video

[@ovtec15]

So i have a 05 rsx with the k20z1 and I’m gonna have to order a new harness but eventually I wanna go k24 bottom so if I swap the sensors n all will it work with my ktuner ecu or would I need hondata?

[@TheGerbsteve]

Should work with your k tuner

[@vibeouttothisyall9575]

Would this work for a base rsx k20a3 swap to k24?

[@TheGerbsteve]

I’m pretty sure you can run k20a3 ecu, trans, and some stuff. You have to look more into it though man, don’t want to get your hopes up

[@TommyBlazeHD]

Google search didn't help. If we have a 8th gen Si, will the stock ECU work? What type of tune is needed? If stock ECU is needed, thinking of using two ECUs so I can pass CA smog. One with a tune, and the original one for passing smog.

[@TheGerbsteve]

Stock ecu works and a tune for k24

[@cleatcheck45]

@@TheGerbstevecan you elaborate on this gerb? Will the z3 base map run the car and pass smog? Or did you have to flash the 24base?

[@DVrec22]

I need to order a clutch kit today and need to know for which car do I buy the clutch kit for

[@DavidTheCarGuy8]

if you have the K20z3 or K2, 4A/A2 you can use the oem civic si clutch

[@cesarz188]

Did you need to flash tune your ECU on k24 after you installed everything ? I heard it’s necessary to do a tune to make the k24A swap run as it should.

[@Red-ev8ls]

Yes it is

[@amored_up]

What bolts did u use for the crv post mount? And are you using the torque mount that was used in the k20?

[@itachithegoatg6803]

on the oil cooler did you feed the block line thru the factory k20z3 fitting on the k24 RAA block without any work

[@TheGerbsteve]

Yeah, everything bolted right up. It's cake to swap everything over

[@itachithegoatg6803]

@@TheGerbsteve Thank You!

[@annmarkjamcom1448]

Hi buddy I’m I have a Honda Civic 2007 1.8L I’m planning to swap k24 can I used the harness and old stock manual transmission?thanks

[@tazimali1650]

Hey Gerb I swap the K2.0Z2 from my Acura csx with K2.4A2 TSX I am keeping the OEM air box what hose to use from the air box to the K2.4 intake manifold can you send me a picture or the part number

[@kymani-vauncampbell341]

*GERB* I’m doing the swap , do I need a tune once I’m finished doing the swap?

[@TheGerbsteve]

I would recommend it

[@kymani-vauncampbell341]

Gerb hey man I appreciate the quick reply I’m gonna order one from eBay right now

[@kodeystockton1124]

@@TheGerbsteve Do we need a special basemap to start with for this swap?

[@Parzival971]

Did you have to tune the car in order for the k24 motor to work

[@TheGerbsteve]

No as long as you are keeping it close to stock (no cams, big injectors, etc)

[@benjaminrivera3106]

After doing all that everything good no light on in the dash? Or nothing?

[@TheGerbsteve]

Everything was good, started it up, no lights, perfect compression along the board, and it ran like a beast!

[@raudyjorge4665]

From what year i need the crv post mount

[@IsaacPoopsAlot]

i think the 3rd gens

[@BoostedGti910]

Brother I’m doing the same swap in my 09 si where’d you get the top mount

[@TheGerbsteve]

Someone actually sent it to me man. CRV post mount

[@tazimali1650]

Hey Gwen if I use tge OEM aluminum oil pan how much oil I have to put in the engine

[@tazimali1650]

Hey Gerb K2.4A2 swap in an Acura CSX OEM same as the Honda si aluminum oil pan how much oil to put with out over filing

[@michaelmercier9569]

How Did you remove the oil cooler stud from the block ??

[@TheGerbsteve]

Took the nut off then used an Allen wrench, I believe

[@K248thGen]

will my k20z3 ac compressor fit the k24???

[@TheGerbsteve]

Yes

[@DiyFg2]

Brother..did you use the same bolts from the z3 to mount the CRV post mount or are they different? Bolts?

[@rhyanreycalamiong583]

Hey gerb can i use my skunk2 alpha header to k24a engine swap?

[@TheGerbsteve]

Yes you can. Just need to find out how many washers you need to use

[@rhyanreycalamiong583]

Gerb how many washers did you use?

[@EddieSwaggy]

Thanks for the video bro! quick question did you have to replace your k20 ECU to k24 ECU?

[@TheGerbsteve]

I kept k20 ecu

[@EddieSwaggy]

@@TheGerbsteve thanks for your reply bro

[@oscarjsm24]

Hey bro so I have a bit of a problem maybe you can help. I did a k24a JDM swap on my fg2. I did the type s oil pump upgrade. But like you mentioned the type-s pan doesn’t have where to Bolt the rear mount. What do I do? Can I use the z3 pan orrr? Thanks for the reply in advance.

[@oscarjsm24]

@@krazykk4 awesome thanks man!

[@oscarjsm24]

@@krazykk4 another question bro. Finally addressing the issue tomorrow. What header are you running?

[@oscarjsm24]

@@krazykk4 thanks for the reply again. Awesome I’ll have to pick up a set. No cutting necessary right? Headers have clearance between them and the rear mount bracket?

[@hassansafeer7411]

Helloo gerb bro, I want to ask u that what is the difference between k24a rbb2 engine, and k24 rbb 3 engine. Like u have rbb 1, whats the basic difference between rbb1, rbb2 and rbb 3.

[@timnies1461]

Gerb, how much hp you think your making right now? Love your videos bro, keep on filming

[@TheGerbsteve]

Hard to say, maybe 210 hp or so. More videos to come for you my friend

[@TheJkrouse88]

What’s up man. So I just got a k24a2. Doing a 20/24 but I’m getting conflicting information on something. With the z3 pan on the 24 block what oil pump and pick up are you running? Did you have to use the z3 oil pick up? Thanks man!

[@drsully]

the best stock oil pump for your application is the fd2 type R oil pump. it has the extended pickup just like the stock z3 oil pump but is closer in design to the k20a2 rsx type s pump. do not use the type s pump because the pickup is not tall enough for the deeper z3 oil pan. its not worth the risk. use the RRC fd2 civic type r pump. its cheap and bolts right up.

[@AlexWaters-i8b]

Did you use the k24 half shaft or the k20 half shaft.

[@TheGerbsteve]

K20 shaft

[@leofabian1161]

Hey question is this swap worth it .. is this noticeable power ? I’m running stock k20z3 with bolts ons and honestly I’m happy with it I just want to know if a swap like this is really worth it power wise

[@darnellbabb3865]

Do yo remember what year crv postmount?

[@joeyortiz2987]

From the CrV that has the k24

[@williampierce5225]

2001 I believe

[@rapture7551]

Hey. I just found out on my 06 si k24a2 swap from 06 tsx . Im running the stock ecu on the k24. Can it ruin my engine? The car is still fast.

[@semaJPlayz]

nope use your stock ecu if your in an 8th gen

[@rapture7551]

@@semaJPlayz Oh ok. Thank you. So, just use flashpro?

[@evoiv98]

@@rapture7551 I wana swap my 07 si with k24. How is it running in stock ecu

[@garrettmehan3904]

With this video, can I supercharge this motor after I swap it?

[@garrettmehan3904]

Or do I need to to more mods

[@TheGerbsteve]

You sure can. Just make sure you get it tuned, run bigger injectors/fuel pump and if you’re running stock oil pump, keep rev limit to 7800 max!

[@em2_7thgencivic5]

Hey @Gerb, great video, if I'm JDM K24a swapping my 7th gen, coming from a d17, do I still need to swap all the sensors for it to fit with a USDM 02-04 rsx type s harness?? 🤔💯

[@paperboyraf1337]

What about the trans. Did they bolt right up ? I have an 07 as well that’s why I ask

[@TheGerbsteve]

Yessir