FORD MONDEO mk4 HEADLIGHT REMOVAL AND BULB REPLACEMENT - DIY

[@lazyspaniel]

Huge thanks for this - only took me 5 mins once I knew to pull the lower corner into the engine compartment a bit. (Feel chuffed with my little self now).

[@DIYProjectX]

So happy to hear this, thanks. Well done, you !!

[@teodorserbanica2137]

Very usefull thank you for the tutorial sir!!!

[@DIYProjectX]

Glad I could help.

[@dannywales7971]

Thats great. Thanks for the tutorial. I have a dead wide bulb i have to change. Also on the same side the main hulb only comes out n after i tive it a bunp on yhe outaide. I hope its just a loose connection.

[@DIYProjectX]

Happy to help.

[@davidbower9103]

So many thanks for posting this - you saved my NYE! I found the hardest part reseating the unit - being winter I was paranoid I might split the plastic bumper grille but mercifully I didn't (wonder how many new ones Ford have happily supplied!). Also lucky that the failed dip beam bulb was a standard H7 55W for which I had a spare.

[@DIYProjectX]

So happy to hear this. Glad I could help. Happy holidays.

[@s1mpleton]

Thanks for this! Watched the video once and managed to change the bulb under 10 minutes without a hitch :) would be a real hustle without your tips.

[@DIYProjectX]

Glad to hear this. Happy holidays.

[@ScroogeGaming]

Thank you for this, my Mondeo's headlights got water in them so needed to know how to remove them, thanks DIY!

[@DIYProjectX]

Glad I could help. Good luck.

[@rya789]

Great job, thanks a lot 😊👍💯

[@DIYProjectX]

Happy to help. Thanks.

[@rudolfabelin383]

Thanks!! It was a little trick the first time with the inner corner. I carefully used a flat screwdriver to "bend" the corner in or out.

[@DIYProjectX]

Well done! Glad I could help.

[@ludjakkivication]

Great tutorial my friend. A month ago i watched another tutorial and it helped a little bit when i changed the light bulb but it didn’t show the tricks that you used. I spent 40 mins changing the light bulb because it was hard to get it out and even harder to get it back in. It sucks that i first connected the light bulb and then put it in its place that’s why the light bulb was a little bit off when i drove the car. Today i had some time to finally put the light bulb correctly and did it in 10 minutes with the help of your tricks. Thanks again for the tricks and the tutorial

[@DIYProjectX]

Comments like yours make me truly happy. Thank you.

[@rumpleforeskin5233]

My tab broke on the connector, wtf do i do 😢

[@DIYProjectX]

That sucks... :( I suggest you tape it in place and then a replacement..?

[@anthonybee1981]

Thank you for this. I've just changed both of my headlamps and there's no way I would have been able to remove the headlamp casing without the 'trick' with the inside corner. You've just saved me a painful trip to Halfords and £18!

[@DIYProjectX]

I'm so happy to hear this!

[@soresilgen9066]

Very helpfull thank you

[@DIYProjectX]

Happy to help

[@Davidallen9]

Great video, thanks

[@DIYProjectX]

No problem, thanks.

[@philgrimes8259]

Clear and straightforward - thank you.

[@DIYProjectX]

Very welcome. Thank you.

[@hubi645]

Is not easy to put it back...But i did it(thank fuck)😊

[@DIYProjectX]

Well done, mate 😀

[@steviemacmuttley]

The connections at 02:05 are not on my headlamp - all I can see are some posts - why is this?

[@DIYProjectX]

Do you have Mondeo mk4? Strange, the headlight must ve connected, it should be there. Could it have broken off, by any chance?

[@blondu198021]

my tab is broken and i’m not able to get the connector out

[@DIYProjectX]

☹️

[@krisekeberg1292]

And now that you’ve handled the globes with your bare fingers they’ll blow very soon due to the oils on your hands! 🤦‍♂️. Always use gloves or clean with spirits!

[@DIYProjectX]

Never happened. But thanks.