Thanks Keith, hope you recover quickly and the pains pass!! I am just finishing up the restoration of my 1972 10EE 20 I/M. This later generation of 10EE lathes replaced the motor-generator with vacuum tube electronic regulator rectifiers for the DC power supply. My machine was being moved with a fork lift and had fallen over on it's face and damaged ball cranks and handles then sat for 13 years with no love. The 2 C16J vacuum tubes were also bad and could barely make the lathe run. It would start running on one tube then the speed control would run away to 1800 rpm. As an retired electrical engineer I designed a solid state replacement for the vacuum tubes. My SSC16J tube replacements worked perfectly the first try, damage repaired and the lathe is back running like new. I am waiting for re-designd printed circuit boards (PCB), they should be here today or tomorrow. I redesigned my prototype SSC16J PCB to be build up for the larger C16J or smaller C3J tube replacements and fit as drop in replacements in the 10EE. The C16J tubes handle the stater winding up to 30 amps @ 0 to 300V while the C3J powers the field winding at about 2 amps @ ~45 to120V. When all 3 tubes are replaced with my SSC16J and SSC3J circuits no warmup delay is required and I can bypass the 2 minute power on delay timer for an instant on lathe ! By eliminating the heaters you reduce the heat by 160 watts and the solid state replacements have a lower voltage drop that reduces waste heat at full power by over 500 watts. The only change to the 10EE required is to adjust the compensation pot in the control module for the slightly higher efficiency of the solid state over vacuum tubes. Adding a single wire bypasses the delay timer for instant on.
@scottpecora3719 ай бұрын
Christ: WHAT? I was told as a child it was just magic which has seemed reasonable through my adult life, only now to discover there's technology and engineering involved!
@ronkellis76911 ай бұрын
FWIW I learned a heat gun will soften up the old sealant and the sight disk will pop right out. The scratches will polish out rather easily, by hand is best as the surface will ripple if friction heated. I used Gasgacinch and haven't got a weep, let alone a drop.
@dagwood132711 ай бұрын
You are doing a great job on the 10EE. Hope your stone passes soon.
@carlbyington518511 ай бұрын
Get well right away Brother Keith !!! Feel Good man,
@richb31311 ай бұрын
Passing kidney stones are never fun but they do pass and you feel better after, Great job with the restoration so far Keith.
@steveschwartz613811 ай бұрын
LOOKS GREAT. KIDNEY STONES ARE NO JOKE. I FEEL FOR YOU. WORST PAIN I EVER HAD. NURSE SAID IT WAS EQUIVALENT TO GIVING BIRTH.
@jdmccorful11 ай бұрын
Ditto, and then some!
@annacalise833611 ай бұрын
I'm a hobby gunsmith and machinist and deal with small screws original to whatever firearm I'm working on and the last thing you want to use is a typical flat head screwdriver, you should get yourself a set of hollow ground bits, the blade has parallel sides and when using the right sized bit wont slip or spin out of the screw damaging the head, they would be great for these flat head screws on this machine, I can't wait to see this machine run, I've always wanted a Monarch 10EE, very cool and it looks great!!
@boogiewoogiebubbleboy287711 ай бұрын
Great content as usual, my friend. I'm a big fan of that colour you painted the body. On my screen, it looks identical to what my friend and I painted all of my mine. I have OCD so the need for neatness where everything matches, like the colour of the machines, is strong. Like you, I have purchased rundown or damaged machines over the years to restore back to factory condition. I have done this for almost 15 years with the help of a dear friend of mine, Buster. Here's a bit of British history for you. Buster is the grandson of the infamous Great Train robber of 1963, Buster Edwards. Together with several other gang members, they robbed a train in 1963 just outside London, on a now famous bridge, stealing over 2.5 million British pounds. That would be about 60 million in todays money. But unlike his infamous grandfather, my friend stayed on the straight and narrow path, becoming an engineer at British Aerospace. Sadly, through an injury he sustained while canoeing, he had to retire from BritishAerospace at the age of 51. But not all was lost because he then came to work for me until his official retirement age of 65 two years ago. Now, he works with me on special projects or when he is bored. Most days, he is here with me, and if not actually working, he's giving out valued advice. Back to you. Like you, we lovingly restored all nine of my machines to an original state when they were first manufactured. Where possible, they get used on a weekly basis, but at the very least, we start them up and run for 5 minutes every day, just to keep the kogs oiled up. The furniture looks great now that it's been painted, polished, and brought back to life. Most of my chrome parts were either too far gone, which meant they had to be replaced with parts from machines broken for scrap or they were hand made. It's a shame about all the runs in your paint. You went so far as to repair, replace, and repaint the machine to a high standard, then let it down because of a poor paint job. Otherwise, what a fantastic looking machine. Can I give you some advice? Those drive screws you used for the serial number plate made by Tom are too short. In no time at all, the screws will become loose from the vibration. I suggest that when ordering replacement hardware for another project, you order enough longer drive screws to replace the short ones. Here in the UK, we have a saying. "The rule of thumb is." In this instance, "the rule of thumb is that there must be at least two-thirds of the screw or bolt needed to secure an object in place sufficiently." It looked to me as though there was not enough screw threads potruding the plate, especially when you hammered the first screw fixing in,vit was wobbly. You had to hammer it a second time and although four screws are used, the plate will still become loose, sooner rather than later especialy if that machine is used regularly. A longer length will enable a good anchor for many life times. Other than that, everything looks perfect.
@TMacinAus11 ай бұрын
I hope you feel better soon Keith! Love your work.
@normsweet171011 ай бұрын
Kidney stones, due to an abnormally small tube from Kidney to bladder on both sides; I can’t pass them, so Dr goes in and blast em with ultra sound, so I can pass em. NO FUN at all. Glad to see you’re up and working on one my favorite projects 👍
@MrChevelle8311 ай бұрын
thanks for the update i was there on the work day he mentioned. and glad to see them working on this machine! it was a busy day! great experience for me and my brother!
@bcbloc0210 ай бұрын
Lathe is looking great!
@blue-runner11 ай бұрын
That's the same model I first learned turning on 50 years ago. My first project was a 3/4" buttress thread for a vise. A beautiful, smooth lathe..
@MHolt357311 ай бұрын
Can't wait to see the chips fly
@one4stevo11 ай бұрын
Looking great nice job. Hope your over the kiddy stone and back to normal Keith.
@ydonl11 ай бұрын
I loved my CASE tractor. It didn't have much top end, but it was a beast off the line. All that torque! Gotta have the right tires on it.
@porthose20029 ай бұрын
Amazing job recreating those tags!
@kats171911 ай бұрын
The Monarch is looking the bucks guts mate will end up better than new . Well bone great restoration.
@robertlevine215211 ай бұрын
Keith, You have my sympathy. I feel for you. The pain can be excruciating. Many years ago I returned home from Pascagoula having spent working for the shipyard only to double over in pain from a kidney stone. I wound spending a week in the hospital. After a football game I went to dinner with my parents and brother. I made a comment that the stone wasn't too painful. My mother responded, "How would you know? You were so full of pain killer you couldn't feel a thing." The Monarch is starting to look brand new. I am looking forward to seeing it run. Bob
@hobbiesrus11 ай бұрын
Just beautiful looking. You are sending that my way when done, right? 😂
@glennstasse569811 ай бұрын
Of all the machines Keith has the 10EE is the one I wish I had. It’s awesome. Thanks, Keith for the ride-along and I hope you feel better!
@garythomas491411 ай бұрын
my sympathies are with you on the kidney stone. When I had one, my sister-in-law informed me that I now knew what the pain of childbirth is like. She has experienced both so I guess she knows what she speaks of! The Monarch is looking great, looking forward to seeing it making chips!
@normmcrae114011 ай бұрын
Looks GREAT - Plastics are usually pretty easy to polish - the hardest part is to NOT polish too much and make it melt. Yup - done that, and had to replace the part...... Hope the kidney stone passes quickly and painlessly!
@bryansmant87011 ай бұрын
Glad you're back on your feet! That's going to be a hell of a lathe when you're all finished.
@EnoRestoration11 ай бұрын
Nice work Keith! Hang in there!
@nealsmith704011 ай бұрын
Keith, sorry about the kidney stone, the worst pain in my life. When you finally pass it you will feel better quickly. Good luck
@BigLapua11 ай бұрын
Be well! We love your work!
@ozar6211 ай бұрын
Having delt with kidney stones in the past I know what you're going through, and I hope all is well now. Fantastic job on the lathe also, love seeing the transition from a barn find to showroom condition.
@geraldharkness883011 ай бұрын
get better soon keith!
@joewhitney409711 ай бұрын
Looking good Keith, getting close. Thanks for sharing.
@CSWeldFab11 ай бұрын
I love the machine tags. That's one of the last things my restored Index mill needs.
@RedDogForge11 ай бұрын
Saw your fb post. Heal quickly brother. Beautiful machine. Im green with envy :)
@unpob11 ай бұрын
Feel better Keith
@5x53511 ай бұрын
GOOD? Shoot fire, Keith, That lathe looks beautiful.
@kevinknutson459611 ай бұрын
Ha! You just said the exact same thing I did when I passed my first kidney stone. It went from "Man my back feels sore" to "I think I'm about to die" in an hour and I was freaking out. Condolences and congrats on passing the beast.
@robertlynch706811 ай бұрын
I've recently recovered from having kidney stones . One trip to the emergency room , several trips to my urologist , out patient lithotripsy , and follow - ups . This was my third bought since the summer of 2016 . I will say I know your pain ! Stay hydrated , drink a large glass of water with a shot of lemon juice , ( as much as you can tolerate) in the morning , reduce the consumption of salt in your diet and certain foods . I'm sure your doctor knows the best course of action . Hope you get to feeling better soon , from a long time subscriber !
@royd.mercer172711 ай бұрын
Great job! Looks like it just rolled off the line. You make it look so easy, even when we know it isn't.
@nobuckle4011 ай бұрын
Looking good! Thanks for sharing the progress.
@jrmintz111 ай бұрын
Feel better soon!
@bearbon211 ай бұрын
Yeah, I've been through the kidney stone drama too. Had to go to the emergency room with a pain level 10. An IV drip of morphine was instant blessed relief. What a wonderful drug for pain as any wounded soldier that survived will tell you. Once the stone(s) are in the bladder it's smooth sailing. When you urinate first pinch off your "hose" to dilate the urethra and build up pressure. When released will fire out those rocks easily.
@donteeple612411 ай бұрын
Keith, The 10EE is looking amazing ! Great work.....Can personally sympathize abt kidney stones, just hope and pray you dont have to get a stent to stretch things for the stone to pass..OMG that is worse than anything of the stone itself.....those that have had it know. Again the 10EE is looking super. Don
@Wachuko-111 ай бұрын
That came out beautiful. Got to love the artful design of old machinery.
@M5888-z3w11 ай бұрын
Your account of a kidney stone is extremely accurate I’ve had two of them ten years apart and your ad lib of the pain of dying I was rolling on the floor. It seems funny now but when it’s happening you think you are dying and don’t know from what hope your pain wasn’t so bad
@erichockuly981911 ай бұрын
I hate to say this Keith, but when I had the first of many kidney stones, my neighbor summed it up perfectly…it is like someone pulling a hot, rusty piece of barbed wire out at the speed similar to starting a lawnmower….and he was right!! Good luck! I have felt your pain many times.
@iDuckman11 ай бұрын
I know where you're coming from, Keith. When the body rebels or the situation turns to shit, some of the best therapy is to get back to work doing what you love. The lathe looks *awesome.*
@gerryoneill888111 ай бұрын
Forgot to say I wish you a speedy and painless recovery.
@elsdp-456011 ай бұрын
Thank you for sharing. Very nice on the sight glasses, Monarch looking nice.👍
@Digital-Dan11 ай бұрын
Well, Keith, you know what the Fisk Tire Boy always said: "Time to ReTire". More days in the shop ahead? I highly recommend it.
@richardbennett605311 ай бұрын
Bless you Keith, I completely sympathize with you on the Kidney stone, I hope the rest of the experience is painless and your back to good health and teaching us about machinery and machining.
@NotJRB11 ай бұрын
Nice video. I always look forward to Monday and Friday mornings. Cleaning the plastic sight glasses is the same basic process as restoring plastic headlights on vehicles. Very doable, but tedious.
@transmaster11 ай бұрын
The joys of the coffee ground strainer. 😢
@elmarqo_344811 ай бұрын
Those site glasses turned out great. Your polishing job worked wonders.
@tomfeller670711 ай бұрын
Keith, thank you for the personal stories and updates. It is one of my favorite things about your channel. You treat us like friends.
@robertschauer37611 ай бұрын
Love the 10ee
@Chillituber9 ай бұрын
Hope you get better soon. This too shall pass...😊
@billdoodson423211 ай бұрын
That lathe is looking fantastic Keith, they aren't at all common in UK, but if one comes up and I have the brass, I think I will go for it. My sympathies about the kidney stones, they really do hurt. When I had two of them (8mm and 10mm), the Lithotriptor that they use to ultrasonically break them up was at another hospital, then they found that the endoscope laser wouldn't work on them either, so they ended up pulling them out with the sort of instrument you would use for picking up a dropped spanner in an engine bay. Very, very sore.
@WilliamLeue11 ай бұрын
I hope you feel better soon, Keith. A kidney stone is no fun at all!
@garyramsey427511 ай бұрын
The 10EE is looking great! Sorry to hear about the kidney stone. Hopefully you’ll get through that soon and be back in top shape, Keith.
@Barnagh111 ай бұрын
Great work as always, and get well asap. I’m just a little surprised that you didn’t refurbish the inside faces of the doors?
@jamesreed612111 ай бұрын
It is good to see that progress is being made on the 10EE. I'm really looking forward to seeing the new electronics in place and working. Some day if I win the lottery I'll get a 10EE for my small shop. KOKO!
@camojoe211 ай бұрын
Kidney stones, been there, done that three times. The last time I couldn't pass it, Doc had to go in and get it. Hopefully you'll pass yours. Regards, Duck
@richardsurber822611 ай бұрын
Wonderful look to the lathe, Thanks for the video. I've been praying for your recovery on the last procedure and noticing the weights loss. Glad most of the pain for the stone is past, pray for that as well.
@stanleyknight817311 ай бұрын
That is one beautiful lathe from a barnyard find to a showpiece. About the kidney stone, a friend had one. The Dr. recommend that he pee into a fine meshed strainer to make sure it had truly passed. He still has his stored in a tiny medicine jar. 😅
@oldgoatherder11 ай бұрын
Keith, you could use one of those headlight refinishing kits to polish the plastic sight glasses. They usually have something to seal the plastic at the end of the process.
@thisolesignguy273311 ай бұрын
WOW the ole 10EE sure looks like a brand new shiny penny! Great job guys! That's beautiful, even for Battle Ship Grey 😁
@walterplummer380811 ай бұрын
Good morning Keith. Hope you feel better soon. Thanks for the videos.
@mickestahl617811 ай бұрын
Love the fantastic work you put into these videos, I hope that the kidney stone get out without to much pain. Much love from Sweden // Micke
@richardtaylor71993 ай бұрын
Great job.
@paulkinzer766111 ай бұрын
I wish you a very quick recovery, with as little pain as possible! And I was very glad when you decided to try to save the plastic windows. I've been amazed at just how clear and clean beat up plastic can be made with several passes through ever finer grit and polish. I love this particular machine as it has gone from how you got it to this beautiful state. I'd love to see an updated shop tour at some point, but you sure have plenty on your plate already!
@GregWhipple11 ай бұрын
I had my first one a few years back... I hope I never get another one. Good grief! Best wishes on your recovery. Nice work on the lathe. It's looking great! I can't wait to see it running.
@scottvolage175211 ай бұрын
Hope you feel better soon Keith. The project is looking good.
@petegraham145811 ай бұрын
Best wishes and prayers for your recovery! The EEE is looking beautiful, looking forward to seeing the electronic modernization work via a performance test! I enjoy your posts !
@ron82711 ай бұрын
What recovery?
@CRUZER180011 ай бұрын
@@ron827 Passing a Kidney stone... Ouch!!
@ydonl11 ай бұрын
Impressive restoration of those sight glasses. I was surprised at how well they turned out!
@tmveronee11 ай бұрын
I hope you get well soon. Thank you for all you do!
@neilpuckett35911 ай бұрын
A beater surface plate, I like that you're a practical man 😊
@SciPunk21511 ай бұрын
Looking good !!
@Tammy-un3ql11 ай бұрын
Best wishes and prayers for your recovery
@johncloar169211 ай бұрын
Thanks Keith for the update video. It all looking good.
@tonyn312311 ай бұрын
Good video. Sorry about the kidney stone. Ouch!
@tomswindler6411 ай бұрын
Very nice,looks good as new .great video 👍👍👍😎😎😎
@mbbmidwest355611 ай бұрын
Be glad you passed that stone!! You're a lucky man...I've had laser surgery three different times since mine tend to get stuck. The after surgery experience (healing, stent removal etc) is...ummm....not pleasant...so when they say to drink lots of water I suggest following through..
@samuraidriver4x411 ай бұрын
The 10EE is looking fantastic, shows that putting a lot of elbow grease into project like this really pays off. Rattle can paint job looks good, alot better then it was before you got started. Hope you pass that kidney stone without to much issues and be up and running again soon.
@bobflores11 ай бұрын
You didn't clock those sight glass screws. 😉 She a beauty of a machine. I'm looking forward to seeing what you figured out for the electrical. I hope you pass that stone without undue difficulty. Take care.
@rexmyers99111 ай бұрын
Yikes! So sorry to hear of your ordeal. Thank you for all you do for us, but, first take care of YOURSELF. We can wait.
@Nf6xNet11 ай бұрын
I'm so sorry to hear about your kidney stone. They're awful! I've passed a few, and the trip from kidneys to bladder are the worst part. The rest of the trip hasn't been bad for me.
@Rovinman11 ай бұрын
Metal Polish works wonderfully for plastic lenses ! Love these restorations ! Tell me about Kidney Stones ! I was operated on with the Hammer and Anvil technique ! I was passing Purple fluid for days afterwards ! 25 years ago ! Stu xx
@andywithers59211 ай бұрын
Its a beautiful little lathe. Nice to get an update on it. It’s amazing the amount of quality content you share with your subscribers with just one day a week in the shop! All the editing and production work probably doesn’t happen my magic either! Thanks Keith. Never had a kidney stone but I hope it’s over and done with soon!
@MrCowering11 ай бұрын
As someone who gets kidney stones every few years, that little sharp pain as the stone goes from bladder to (ahem) toilet becomes a welcome feeling! Good Luck Keith
@ypop41711 ай бұрын
Very Nice Job Keith ! Glad you are feeling better!
@willfromhythe11 ай бұрын
The work looks amazing, factory new condition 👌👍👍
@mdlanor541410 ай бұрын
The Monarch 10 EE is the ultimate dream Lathe. That virtually all machinists would love to have in their shop. The only problem I see with the Monarch 10EE is the vacuum tubes and the other electronics that control the lathes motor. Are not being produced anymore. I often wonder if there are any Monarch 10EE’s out there that the original motor controls still function? I would think most machinists would do a conversion to eliminate the vacuum tube and electronic motor controls. Anyway good luck with restoring all the machines you restore better than when they were new. I often wonder what became of the Steam Locomotive Stoker Engine? The last video I watched on the Stoker Steam Engine. You were trying to figure out how to mill the main body section that was spray welded. Did you give the people that owned the Stoker Steam Engine back to them? It doesn’t make sense that quite a few Stoker Steam Engines were not sent to a scrap yard. They became common place as the Steam Locomotives Fire Box became so large that a Fireman could not keep up with the demand for coal by manually shoveling coal into it. My Great Great Grandfather was a Fireman on the Pennsylvania Railroad for 10 years before he was permanently promoted to Locomotive Engineer. I can still remember his son. My Great Grandfather telling his stories of his father and himself. My Great Grandfather was also a Fireman and Promoted to Locomotive Engineer on the Pennsylvania Railroad. My Great Grandfather would tell my brother and I. Stories of shoveling coal into the firebox on Steam Locomotives. As the Steam Locomotives size and firebox became larger and larger. That it was near impossible to keep up with shoveling the coal into the firebox. That the Locomotive Engineer would also help shovel coal into the firebox. My Great Grandfather was so thankful when the Stoker Steam Engines started being installed on the largest Steam Locomotives. That as a Fireman. There were times when it would rain and then freeze the coal in the Tender. That he would physically have to break up the ice riddled coal. To prevent the Stoker Steam Engine Worm from getting jammed. He said the Stoker Steam Engines Worm would get jammed sometimes. Making his job even harder. Manually shoveling coal at the same time trying to free the worm that fed the coal into the firebox. Usually getting jammed from a rock that was missed in the coal. He told us the first Stoker Steam Engines didn’t have a reversing lever. So he couldn’t reverse the rotation of the worm to get it unstuck. Many of the K-4’s never had a Stoker Steam Engine installed. Mainly only the huge freight Steam Locomotives had Stoker Steam Engines installed. He had also told us. The Pennsylvania Railroad tried to have 2 Fireman on the huge Steam Locomotives. That there wasn’t enough room in the cab of the Steam Locomotive for 2 Fireman and the Locomotive Engineer. For the 2 Fireman to shovel coal into the firebox. My Grandson is now a Seventh Generation Railroader in my family’s railroad history. He just recently passed the Conductor Course.
@WayneT5111 ай бұрын
Coming along nicely Keith.👍 Good luck with the stone, try not too break anything when you pass it.
@ccrider539811 ай бұрын
I know from experience how painful kidney stones can be. Surgery for them isn't a lot of fun either. Keep up the videos. They are very enjoyable.
@sd459411 ай бұрын
Long term = bandsaw. The Buice collection is very impressive
@kevinwayne754611 ай бұрын
looks great!
@nkelly.911 ай бұрын
Goodonya Keith. Keep going Mate. Best wishes with your health. I have been told that the pain from those stones make your eyes water.....
@Krzysiek10611 ай бұрын
The best wishes. I make my carpentry workbench nine months end it is not finished yet. Compared to me , you go with your project like a storm.
@tosselton29111 ай бұрын
I have had many stones and have found the most relief is just lying in a hot bath i've had them blasted and cut out but prefer the knife as I always wonder about the fragments starting new stones! Best wishes my friend.
@mickralph462311 ай бұрын
Take it easy Keith. I have had a few K stones and they are definitely very very painful. You need fluids and pain meds! Hope you pass it soon and painlessly mate, The 10EE looks awesome!
@quintinsmits11 ай бұрын
If those little sight glasses are anything like the plexiglas watch crystals of vintage watches, 'polywatch' is a great polishing compound for them.
@WillyBemis11 ай бұрын
Dear Keith, it is wonderful to see so much progress on the lathe! The tags look great and the paint looks good too!