Kemper Profiling Amp with Behringer FCB1010 (no chip). Part 1.

[@andraskokavecz]

Very nice tutorial! It's 2023 and I am still using it to learn how to program the FCB 1010. Thanks a lot! 🤘

[@marc_leblanc]

Much less expensive than the Kemper remote. Thanks for sharing this!

[@JohnStraussmusic]

I know this is old but its still great for showing everyone the FCB1010 programming. I almost didn't watch it all the way through because you were talking about stuff I did not need. but once you got to the FCB1010 man you did a great job explaining it. Thanks for sharing

[@konstantinilin]

Cheers, man! Thanks for the feedback!

[@zipperhead101]

I am so grateful to you for putting this out there. I was intimidated by the stories I heard about how tough it was going to be to program this controller. I do believe I can get it done with your excellent video, and the one to follow is no doubt just as good. Thank You!!!

[@Domio2000]

Your video was a huge help for me getting started with my Kemper and FCB1010. Thanks so much!

[@konstantinilin]

+Feckless Productions Thanks for the feedback! Glad to be helpful!

[@Podjack]

Hi Konstantin! Thanks for showing this as it was really helpful. Happy New Year to you!! Sheldon

[@konstantinilin]

Thanks a lot, Sheldon! I really appreciate your kind words! Happy New Year to you too!

[@ZillaYT]

How do you do a performance change with the controller, just a bank?

[@wikstroms]

I have FCB1010. I don´t want to have programchange. Only snippets on our X32 mixer and this is midi channel 2 on the mixer. Can you make a simple film about this configuration. Snippets on the mixer is 00, 01, 02, 03, 04, 05, 06

[@ShawnHolderfield]

So, rather than assigning a specific rig to a specific button, how would you 1-5 to rig 1-5 on any given performance?

[@javyclubsoda]

hi, when are you release the part 2 of this video?

[@konstantinilin]

Will do it today! Great that it is required! Actually it is filmed already, just need to make a cut.

[@diecaverna]

what about tap tempo?? how can I control my tap tempo (delay)

[@barrettjulian]

Hi Friend ! Julian again. I have another question. If I want to set up a DELAY for example, but I wish turn on it with the pedal number 6, and then I want to turn off it with the same pedal (Number 6 again) How I should do ? Now, when I want to turn off the stomp boxes or MOD or DELAY independently, I have to press the program botton and everything get off. EXAMPLE: PEDAL 1 (HI GAIN) when I press PEDAL 7 MOD IS TURN ON - when I press PEDAL 6 DELAY is TURN ON... If I want in this moment just turn off the MOD, I CAN'T, and I need pressing again PEDAL 1 AGAIN and put MOD with pedal 7.

[@konstantinilin]

Yeah, this is not possible. That is the one limitation without specialized chip. You need to press either program pedal again to reset to original settings of the preset or to use two different pedals: 1 for switch on, 1 to switch off.

[@barrettjulian]

Friend ! I have great news for you, I just result the riddle !!!! It is possible without de special chip. I tell you how. Example: Will suppose that you have setting a DELAY in a pedal number 8. Well, You are sending this information with 6 in the value 20 and some value more than 00 with the expression pedal... then you hold numer 7, push again 7 and light sarting blinking, you select value 20 again , then you push UP and push de expressión pedal to 00. NOW WHEN YOU PUSH THE PEDAL 8 WILL THE DELAY TURN OFF ! Try it !!!!!!!!!

[@konstantinilin]

Ok, so as I understand in that setup FCB will be sending two control messages to Kemper every time you press: one with 00, one >00. I actually tried this couple years ago. But it didn't work. Basically what happens - Kemper receives two messages simultaneously to switch delay on and off. I suppose they have implemented the code to handle this situation correctly, if it works for you now! Good to know, mate! Kemper guys are doing great job in firmware! Thanks for letting me know.

[@barrettjulian]

You are welcome my mastero

[@samtheinsaneshred]

This is so confusing mate

[@MiNdLeSs1234567890]

Nice setup 👌🏻 the band Trivium uses Kempers with Behringer controllers

[@FelcSE]

Why are all the bottom 5 buttons starting to flash when I hold the down button?

[@konstantinilin]

I don't have the controller for several years already, sorry. Check the user manual, it should describe stuff like that.

[@AdTheMusicMan1991]

Am I rite in saying for instance. Say in a gig I would like a few patches I can assign. Patch 1: 1-clean. 2- crunch 3- chunky gain tone 4- lead sound Etc. But for different songs in a set list I can move up the bank to number 2: And do the same again. 1-clean with some chorus and delay. 2- chunky gain. 3- lead tone with delay Etc??

[@konstantinilin]

Correct! That's how I use it. Also you can assign couple of free pedals to switch on or off stompboxes. Just in case you want to add extra boost or delay.

[@thenoisyguitar]

Great guide! Thanks for sharing! Gonna buy a unit soon!

[@Hucho]

Hi Constantin, First of all many thanks. A while ago I programmed every slot till performance number 12. Now I wanted to program it further with your videos and then what happened: I want to program performance number #61 in bank 03 on the FCB1010 using footswitch number 6 on the FCB I do this: while having a LED red on footswitch 6 and bank 03 on I press and hold down once. Then I press up once. Then I press the footswitch 6 once so it starts blinking. Then I press up once. Then I type 61 and press up. Then for some reason 61 starts blinking once again on value 1 so I press 61 once again and press up again. And then I hold down and I'm back but for some reason it doesn't work. It doesn't sent 61 to the kemper :( Could you help me out ?

[@konstantinilin]

So here're your steps: 1) hold 6 in bank 3 to edit pedal dettings 2) Press Up 3) Press 6 4) Press Up 5) Type 61 etc... The mistake is on step 3. After step 1 and 2 you are in the pedal 6 settings. Now you need to choose what message to send. To change banks you need Program Change message. You want pedals 1 or 2. Pedal 6 sends Control Change messages. So try to all the same actions but on step 3 press pedal 1. Btw, since you've already changed you settings for pedal 6 in banks 3, when you get to step 3 you'll notice that pedal 6 is lit. Make it switch off. I think you should hold pedal 6 to make the light shut down. This will prevent controller from sending wrong Control Change messages to your Kemper.

[@BenvanGeest]

Thanks a lot for the explanation on how to programme the Behringer FCB1010! This was extremely helpful. However - is it true that you can only add two stomp box effects per bank? Let's say I want to add a delay on controller button 8 on bank 00. Then I'll set it to on, on button 7. Then I will add a reverb and I set it to button 7 and set it to on on button 6. However, when I try to add an effect on let's say button 9 it no longer works because 9 will have a different configuration now. In other words - it seems you can only use effect stomp boxes on button 6-8 and in reality this means only two stomp box effects effectively per bank. Is this correct? Thanks!

[@konstantinilin]

Hi, thanks for kind words. Each pedal in bank can send 2 stombox control messages at the same time. So, with th each pedal you can control two stompboxes at the same time. So it is two stompboxes per pedal, not per bank. In one bank each pedal is capable of changing presets as well as stompboxes. Does it make sense to you?

[@BenvanGeest]

Thank you for your response! Much appreciated. Well, you see - when I apply both a reverb and a delay for let's say pedal 1, then for pedal 2 the same two effects are already applied as well. So, I don't know what's going wrong here. That's why I thought maybe there's a maximum of two effects per bank instead of per pedal. Do you know what I mean?

[@konstantinilin]

Ben van Geest What do you mean by "for pedal two effects are already applied"? And what configuration do you have for pedal two? I mean, which functions did you configure on it?

[@BenvanGeest]

What I mean is this: when I apply two effects for pedal one (for example a delay and a reverb) and I want to apply two effects on pedal two then the effects I already applied for pedal one are ALSO applied for pedal two. SO, when I want to edit the effects on pedal two I ALSO change the effects for pedal one. This is obviously not what I want. So, now it seems I can't edit effects separately from pedal to pedal you see?

[@konstantinilin]

How exactly do you apply effects to pedals? What do you change?

[@justinarmbruster3960]

Do you have to program the fcb1010 first?

[@konstantinilin]

Justin, maybe I misunderstand your question, but in the video I actually explain how to program the controller.

[@justinarmbruster3960]

Ya I got it figured out. I was just confused because all the other videos said you had to program it first. Thanks for the video it was very helpful!

[@konstantinilin]

@@justinarmbruster3960 Thanks! Glad it worked out for you.

[@diegochinellato6550]

Hi Konstantin, Thanks for you guide, it really helped me in getting started with this pedalboard. I actually had no idea about what to do. I configured the first 5 presets of a perfomance with pedals 1-5 and they work correctly. Then I tried to configure the volume pedal in the same way you did for preset #1, the "switch 1" led activated but it just doesn't work. Any suggestions? Do I have to tweak some Kemper setting?

[@diegochinellato6550]

I solved the problem: I had to calibrate both expression pedals and now they work.

[@pililaman97]

@@diegochinellato6550 How did you calibrate them?

[@diegochinellato6550]

@@pililaman97 I'm sorry but I really don't remember. I used it for a small time then switched to the kemper remote, it's way better.

[@AntEnnit]

Great videos! Thank you!! Is it possible to use the screen as a tuner like you can with the chip? Or can you not use a tuner?

[@konstantinilin]

You cannot show tuner on FCB screen, only on Kemper screen. The great feature in Kemper is that it shows tuner when Volume pedal is in Heel position - when sound is muted.

[@JW-ne6qg]

Thanks for this great tutorial! Just one question: The stompboxes that I have configured for my performance are all switched off once I save the performance to a button on the Behringer. Does that mean that I have to configure all the stompboxes seperately like you showed in your second video? My idea was that for example the compressor is always on with the performance and I could add a boost if I want by configuring button 8 for example. Thanks a million, again!

[@konstantinilin]

Hi, I'm glad that it is still helpful even though it's been a while :) The initial state of the performance can be saved. And when you switch to that performance later that state will be restored. So if you want the compressor to be always on, just enable it and then save the performance.

[@JW-ne6qg]

​@@konstantinilin Thanks for your super fast reply. Unfortunately it doesn't work that way. The compressor is on until I press UP for the last time to save the changes (Step 8). This goes for all effects in front of the amp in the signal chain. On the other hand, reverb, delay etc. after the amp stay on. Strange, isn't it?

[@JW-ne6qg]

OK, I found the bug :-) It's in the rig manager! Storing the stomp box there isn't enough, it has to be stored in the perfonmance on the Kemper itself, then it isn't turned off when stored.

[@konstantinilin]

I usually modify performances in the Kemper unit itself. I use Rig Manager occasionally if I want to browse through many profiles.

[@gianpietrocollavini]

Great man! Good job!Thanks a lot.

[@chopshop777]

Best video on this subject, Konstantin I know you recommend being in the Perform mode but your instructions will work in the Browser mode as well. no ? cheers. Ed

[@konstantinilin]

+Ed Mehrzad Hi, thanks for the feedback! Sure, the controller will work the same way and you can apply same configurations. Though in Browser mode you have to do one extra step: - go to Browse Mode PrgChg page in System settings and select the Program number for the rig. In Performance mode they are assigned to performance slots already and in Browser mode you have to assign them to rigs manually. To get to this menu press SYSTEM hardware button, navigate to page 7 (in my firmware 3.0.2, might be different number of page in other versions). I have assigned QUICK hardware button to open this page, so I can access it very fast. Hope it helps! =)

[@chopshop777]

Konstantin Ilin Awesome Konstantin, thanks so much. would you happen to have a facebook page so I can add you to friend's list, if you don't wanna post it here it would be great if you could send me a message through youtube if not that's cool too. all the best. thanks again. cheers. Ed

[@konstantinilin]

+Ed Mehrzad Sure! I have personal page and music page. Would be happy to add you. facebook.com/konstantin.ilyin facebook.com/KonstantSingularity

[@chopshop777]

cool, got both of them, just sent you a friend's request, thanks Konstantin. cheers. Ed

[@ethanmiller473]

Thank you for this video! Very helpful.

[@improvementyard]

awesome video. thanks

[@haveguitar]

Great video, thanks!

[@konstantinilin]

And here comes the Part 2 kzbin.info/www/bejne/f5PHeml9jN-dqpI

[@robertoponte]

Great video!! Thank you very very much!!