I make 220v electric Wind Turbine generator

[@kinghomemade]

*I turn shock absorber into a Cylinder Generator 90 degrees* kzbin.info/www/bejne/pnnCimCibZWdibMsi=kD0hVtZFO5ATaa3A

[@jdcrunchman999]

King home made, I’m really impressed with your workmanship, but please please don’t “fake” the numbers. Invest in a watt meter, and also show the real voltage you get from your generators. We are also interested in knowing the voltage drop one occurs when putting a load on the generator. Just be real dude…. And keep up the good work.

[@galaxymyt4834]

This trun on one 1.2HP motor and one fan together

[@nonyabusiness9747]

Agreed

[@nonyabusiness9747]

@@galaxymyt4834 what?

[@B52-v4h]

@@galaxymyt4834 its less than 0.5 hp

[@B52-v4h]

and its take like peak 10 amp and continuous like 1.5 amp to know the watt you 1.5x220=330 i guess its 400watt generator and its great any way

[@jeffmccrea9347]

I think it's a shame that he did such quality mechanical work just to bullshit about the output. I mean the reuse of stuff around him and the workmanship was genius but those coils, even cooled by the epoxy won't handle 8 Kw. I have a 7 Kw Troy Bilt gas generator and the generator head alone is the size of 3 shoe boxes. I question where the power was actually coming from because he had the yellow cable from the mill UNDER the spool by the fan then he had the fan and pump plugged into the spool. I suspect that the cable ended under the spool and the spool was plugged into the house through a hole in the roof. Also, he had no speed governor on the mill to avoid appliance burnout in high wind situations. The sound of the pump remained at a constant tone as the mill sped up and slowed down. The pump speed should have varied with the mill speed. He also had no mechanism to avoid having the output wire from wrapping around the mast as the mill turned and change direction as the wind changed direction. This is done with carbon brushes and slip rings on small units like this. He also has no 50 Hz frequency regulation. This is not important for light bulbs but extremely important for motors. With a rectifier bridge and some regulation, it would be a pretty good project to charge batteries and run an inverter.

[@GopalanSampath]

Yes yes yes and yes. Totally suspect the stuff, though the build idea appears ok, still mech stability, electrical stability, safety are issues remaining to be answered.

[@abhimanyumonu]

the rpm of motor is more then the windmill, totally fake 😁

[@jamilb327]

its max 300 w depend of cable size also when wind rotate the main fun cable will cut . Any way nice idea he need to make it 6 coil to get 3 line and but dc control

[@derpinbird1180]

This is for developing countries and stuff where you cant just get/afford that stuff. If you were careful with how you used it you could use it for a range of things

[@lucastonoli3256]

@@derpinbird1180 No one is questioning the application or the use of spare materials. The issue here is fake figures and promises.

[@snow_the_dev]

I dont know if it will generate 220 volts. Im sure it generates something, but not that high.

[@filipecb]

I have some question: 1st: It is well known that the required mechanical rotational speed of the rotor depends on the number of poles and required electric frequency. It is given by the formula: S = 120.f/p where: S: angular speed in RPM (rotations per minute) f: electric frequency in Hz p: number of poles in the rotor. Example: for 60Hz, given that his construction shown in this video has 4 poles, the required mechanical speed should be: S = 120 * 60 / 4 = 1800 RPM. So, unless the turbine rotates at 1800 RPM all devices connected to the turbine will be running off its nominal frequency, wich lead to serious problems no only for the devices as well for the generator. Unless you connect some power electronic devices such as Rectifiers and inverters, this kind of assemblage could not work for most electric devices. 2nd: you have used coils with no magnetic cores, which makes it "high reluctance" , in other words, low magnetic coupling poles, limiting the efficiency of the generator. So, it would be very interesting if you make a video showing: - Electric measurements (voltage, frequency and current being drained from your turbine. Just use some multimeters for that, Im sure you have some. -Give more details about the electric scheme (how you've wired the coils. After this, I'd be encouraged to repeat your construction! Nice video, though!

[@anthonymensah2855]

I concur

[@alifact2535]

The idea is good but there are observations 1 Wind speed is a limiting factor for energy production 2 The height of the fan assembly from the ground is a specific factor The higher the height, the higher the wind speed 3 The number of coil turns is a limiting factor 4 The strength of the magnets is a limiting factor 5 How do the wings rotate while they are flat We did not see the angle of inclination of the wings. Running a water pump& table fan at such a slow speed for fans is impossible

[@gustavobaires2849]

Maybe you could have a part of reason, but he did it and you,,, Don Quixote says "let the dogs bark, a sign that we are riding, Scientists method obligues you to make essays to affirm what you say .

[@jeandrapeau7449]

@@gustavobaires2849 Cuando los perros ladran NO siempre es señal que vamos avanzando o porque lo dice el hidalgo va a tener razon? No tienes mucho cerebro pero si mala fe, encanto!!!!

[@mangaTV110]

He was able to make the wing’s rotate even when they’re flat! It proves that he’s a real genius 👏🏻

[@Suzuki_Hiakura]

Pausing the video at 0:03 I can see how the wings are angled, it is subtle, but it is there.

[@MaDalamery]

15:50 when he is assembling it you can see that the piece of metal is bent to a certain angle

[@aliatef8006]

Well done. You need a breaking system to adjust fan velocity when wind speed increases otherwise van might be damaged or produce over voltage . Moreover you need to add a voltage regulator to adjust electricity output. You are ambitious guy.

[@theinstallerguy786]

You could’ve mentioned to make sure the gas bottle was empty! I got my neighbour to cut it because I don’t have an angle grinder, god bless his soul. May he rest in peace!

[@Time-cc2qb]

What ?

[@Time-cc2qb]

Sarcasm right ?

[@ReinierK123]

You mean, may he rest in pieces... (hell I hope this was sarcasm)

[@ldrcoupleinlove910]

He did that by tapping on it

[@VisTerAl0ne]

What?

[@flymachine]

Very clever indeed, if you angled your cut on the pvc pipe and kept the natural curve of the tube you could taper the blade which would be surprisingly much more efficient, you also need some sort of regulator to manage the surging and drop off

[@rogerphelps9939]

No it is not. The whole exercise is a waste of time.

[@TheRaptureIsComingSoon]

@@rogerphelps9939 can you please elaborate ?

[@3d.printed.flight]

Yes wy did you flatten the blades

[@dnomyarnostaw]

​@@TheRaptureIsComingSoon He is losing extra performance that an aerofoil shape would provide

[@TheRaptureIsComingSoon]

@@dnomyarnostaw thank you !

[@broniuksantanuks6605]

I don't trust people with flipflops. 🤣

[@Dead_inside....]

Класно придумал, и от воды защитил👍 Но нужно подумать про передачу электричества через щётки. Провод может запутаться и оборватся.

[@kinghomemade]

ok, thank for your intention

[@Dessa_O]

Больше ничего там не смущает???

[@jdcrunchman999]

There are no brushes, at least not that I could see

[@Drnardinov]

great job on the editing, and nice safety sandals! I have a pair just like that.

[@Mk101T]

LOL ! props I guess ... and you still got Five Toes :? i couldn't do it ;...* We'll actually I have to confess ... I work in crocs / Louisiana / the heat is to much for work boots. This winter though ... looking forward to wearing boots

[@billhall8745]

He didn't even have the sandals on in one part of the video. Can't have been doing this long as he still has all his toes

[@MrNelsonhsieh]

The taller the windtubine, the more power it has,

[@1943L]

Brilliant use of things available to use. I feel 8000w sounds a bit ambitious.

[@rajeshks2040]

I would love to have atleast 1.5kw setup. It is more than enough to meet my energy demand (energystorage device needed). And I would want the turbine blades to be made of stainless steel sheet (eco friendlier than plastic that release micro plastics)

[@rajeshks2040]

@irmux skeptic stainless steel sheet can last longer... and a structure that lasts longer is less harmful than the ones that you have to throw out frequently. And solar panels? Miniature wind mills can be made better than those. And the market doesn't matter to me, because it is irrelevant to how harmless it is to nature. And solar energy requires more energy storage units than smaller wind mills to just power your house.

[@obc7523]

@irmux skeptic output depends upon which factors?

[@DL-kc8fc]

@irmux skeptic A black electric cable runs from the small roof to the bottom of the pinwheel tube. In the upper part of the pipe, the electric cable is led out and connected to the yellow extension cable under the black isolepe, which is to mask this connection and at the same time hide two weak wires from the "wind turbine". It's a typical Copperfield trick that offers a fake switch ("wind farm") while energy is distributed from the home grid along the same path. Apparently it didn't work well, and the boy decided to capitalize on his investment as a KZbin trick. That's what many do. In terms of psychology, why would someone who has photovoltaic panels, that is, have a relationship with it and prefer proven technologies, attach a cord to an ugly wind farm that can't rotate 360 ​​degrees, is unstable, and has bad propellers. That is not normal. As for the project itself, which can work to a limited extent, there are a few mistakes. I will list only the most important ones. The gap between the rotor and the stator must be minimal, almost to the thickness of the paper. The magnets must be made of rare earths - they must have a high magnetic force and if the iron cores of the coils were used, preferably of transformer sheet, the effect of magnetic flux would be 10,000 times greater, but with alternating currents it is possible to use air coils - it's such a dynamo without commutator. The number of threads cannot be 300, but 3000. Just a lot of bugs that didn't work as planned.

[@knightgroup9167]

@@DL-kc8fc Is it possible to make an 8kw generator(as like you said rather than of 300 turnsbut 3000 turns) in this concepts adding some corrections over there .hope valen tino can givesome points.We have an situation of getting 9,000 Rpm where the torque is low can we generate 5-8 kw from it

[@wladimirfadeev9222]

Этот ветрогенератор должен был остановиться при включении вентилятора,а он ещё и помпу включил,ай да шутник.

[@sf_perforator]

Почему он должен остановиться

[@YanCen]

там еще поди бойлер греется от этого карлсона, мощи то девать некуда

[@олегсиниченко-й4е]

вентилятор то в одну сторону то в другую крутится а листья на деревьях не шелохнутся это всё на КЗ работает?

[@user-zq8bn4yp7Vlas]

Дурилка картонная! Таким генератором только телефон заряжать, и то ооочень долго. 😜

[@modpovel]

Ахахахаха, волшебник а. Привет от д. Дью,наепщик

[@JosefMPjess]

8000W/220V = 36A. And the coil wire did not overheat and caught fire.. AMAZING!!!

[@jokerx6520]

What is the size of the wire used in the wind turbine please reply from you

[@JosefMPjess]

@@jokerx6520 by the look of it it is 1 mm wire. Or, maybe you shall ask the maker of this film

[@jokerx6520]

Thanks

[@serhiyshudrec1311]

Ой да ладно ,при больших оборотах еле лампочки светились, а при таких низких оборотах 2 двигателя крутит. Ну да ,твой бы кпд устройства, можно было бы за вечный двигатель уже и не заикаться.

[@jeyphotographer7961]

смотрю креосан видео

[@dembeldembel2031]

Да он просто приколист. Это все ради лайка 😁

[@julioizaguirres4385]

Menos contaminación del planeta si fuera así otro gallo los cantaradesde Honduras tegus ❤😂❤❤😂❤😂

[@AmjadMiandad]

Very well done. The fan part didn't work practically with motor. But its a good project and someone can use basics you shared to make a good turbine.

[@gananathbarik8021]

Uja

[@СашСавар-ф5д]

Мне нравятся такие "бессмертные" которые пилят болгаркой без защитного кожуха! Премию Дарвина этому индивиду!

[@Dessa_O]

Тебя только это смутило в данном ролике??

[@neuser1308]

Меня лично поразило, что у него на все хватило одного диска. Уже обманом пахнет.

[@Dessa_O]

@@neuser1308 да это вообще видео для лохов,нет для ЛОШАР!!!

[@tuankhangly3701]

Hey you are Viet Namese right?

[@СлавикБрынзов-у7д]

Не ну ты конечно молодец)) но только работать твоя игрушка не будет))

[@vadimchernov2509]

ну если дополнить аккумулятором с преобразователем то заработает))

[@mistar-t]

это для хомячков видео, там столько наговнил он это просто жесть

[@n.8337]

Обмотки без сердечников залил эпоксидкой 🤦‍♂️ в катушках не возникает магнитного поля, а следовательно ЭДС.

[@mistar-t]

@@n.8337 там без сердечников нужно, я нормальный другой видос смотрел

[@n.8337]

@@mistar-t значит в другом видео тоже лапшу вешают. Это тоже самое, что из трансформатора убрать магнитопровод, и наивно думать, что всё будет работать. Работать не будет! Автор видео лукавит широкой публике. Если бы он хоть чуть-чуть разбирался в физике процессов, то не было бы так палевно... Но он решил врать, так врать. Во-первых вышеупомянутые катушки без сердечников, во вторых сам процесс преобразования механической энергии в электрическую. На видео видно, с какой легкостью он вращает вал и вырабатывает энергию достаточную зажечь несколько ламп накаливания. Это откровенная ложь. Да даже по видео видно, что изменение скорости вращения выла генератора не соответствует изменению яркости ламп. В общем никому не советую повторять это поделие.

[@falcon4232]

سبحان الله وبحمده سبحان الله العظيم واتوب اليه عدد خلقه ورضى نفسه وزنة عرشه ومداد كلماته ❤❤❤

[@NOVA-dc8hi]

عربي متخلف .. مزلت تومن باله

[@falcon4232]

@@NOVA-dc8hi البعرةُ تدلُّ على البعيرِ، والأثرُ يدلُّ على المسير، فسماءٌ ذاتُ أبراجٍ، وأرضٌ ذاتُ فِجاجٍ، أفلا يدلُّ ذلك على العليمِ الخبيرِ فهـذا الإمام أبو حنيفة رحمه الله يعرِضُ له بعضُ الزنادقة المنكرين للخالق، فيقول لهم: ما تقولون في رجلٍ يقولُ لكم: رأيتُ سفينةً مشحونةً بالأحمالِ، مملوءةً من الأنفال، قد احتوشتها في لُجَّةِ البحرِ أمواجٌ متلاطمة، ورياحٌ مختلفة، وهي مِنْ بينها تجري مستويةً، ليس لها ملاّحٌ يجريها، ولا متعهِّدٌ يدفعُها، هل يجوزُ ذلك في العقل؟ قالوا: هـذا شيءٌ لا يقبلُه العقلُ. فقال أبو حنيفة: يا سبحان الله! إذا لم يجزْ في العقلِ سفينةٌ تجري في البحرِ مستويةً من غيرِ متعهِّدٍ ولا مُجْرٍ، فكيف يجوزُ قيامُ هـذه الدنيا على اختلافِ أحوالها، وتغيُّرِ أعمالها، وسَعَةِ أطرافها، وتباين أكنافها، من غير صانعٍ ولا حافظٍ؟! فبكوا جميعاً، وقالوا: صدقتَ وتابوا. هـذا القانون الذي سلّمت به العقول، وانقادت له، هو الذي تشير إليه الاية الكريمة: {أَمْ خُلِقُوا مِنْ غَيْرِ شَيْءٍ أَمْ هُمُ الْخَالِقُونَ *} وهو دليلٌ يرغمُ العقلاءَ على التسليم بأنَّ هناك خالقاً معبوداً، إلاّ أنَّ الايةَ صاغته صياغةً بليغةً مؤثّرةً، فلا تكادُ الآية تمسُّ السمعَ حتى تزلزلَ النفسَ وتهزَّها.

[@falcon4232]

@@NOVA-dc8hi اسال الله ان يهدي قلبك للايمان ،❤

[@-alqahharservent6203]

@@NOVA-dc8hi طيب خليك هكذا لا تؤمن بالله حتى يأتي يوم الوعيد فأين المفر ؟

[@NOVA-dc8hi]

@@falcon4232 ههههههه اينشتاين هو القدوة و ليس رسول سخيف مختصب اطفال

[@Rehmatullah-c4x]

Excelent createvitiy

[@anthonycali6880]

Great job, I couldn't stop watching! Lots of work.

[@z810f]

Yes and totally FALSE

[@anthonycali6880]

@@z810f Hi, most of his loads had no real load. I certainly believe the motors fan and pump turned. But I suspect under even a mild load, there could be issues. But it was a great video!

[@MasterFeiFongWong]

This may be off topic but I think someone might find it interesting. :D Over Unity Water wheel electric generator: Top of structure has Huge slanted basin (If looking at it from the side it would be slanting down to the right). When filled with water the water naturally slides down and over edge where it starts falling straight down causing water wheels to spin. Water wheels are stacked on top of each other not touching but close. As water falls it hits them all one after the other making them all spin as it makes it's way to the bottom. At the Bottom of the structure there is a large slanted basin. This basin is slanted in the opposite direction to the one on top so the water slides down to the left, into a pool of sorts that is U shaped,(imagine right below the water wheels is the shallow end and as it slants down it gets deeper for some distance then winds around to the other side of construct and comes back up to another shallow end. Now directly behind the water wheels on a flat surface that is above the pool of water that's curving around it, there is another wheel positioned vertically but this one is not a water wheel, this one has powerful magnets embedded horizontally inside of it on both of it's flat sides so there magnetic repulsive field is pushing outwards away from the disc on both sides. (Also each embedded magnet is surrounded in high permeability metal or Mu-Metal to focus it's magnetic field lines into a condensed strong field. This disc is powered by one powerful electric motor. Now imagine long hollowed out cylindrical tubes submerged & sticking out of the pool of water and reaching all the way up and into the basin that holds water on top. Now imagine each tube has a windy slide inside that goes from top to bottom. Now imagine the tube has rings around it that are magnetically repelled so when the main wheel spins around the horizontally positioned magnets hit into the side of these rings causing the entire cylindrical tube to spin. The spinning motion of the tube will cause it to scoop up the water in the pool and the centrifugal force of the spin and the windy slide inside will guide and force the water back to the top. Now remember for this to work properly there needs to be enough water wheels spinning to generate more electrical current then the motorized wheel needs to spin. Key Element 1: Number & quality of water wheels. Key Element 2: Quality of electric generator connected to each water wheel. Key Element 3: Enough tubes to pull enough water from bottom basin back to top basin to equal the rate and amount of water filling both basins at any given time. Key fact: The accumulation of electrical current from the electric generators connected to the water wheels must be greater then the 1 electric motor needs to spin. Key Fact: One must divert the needed electrical current from the generators connected to the water wheels to the motor spinning the disc that has the magnets on it. Key Fact : If this is done properly it would be an over Unity Electric Generator. Reason why some may think this would not work: Some would say the amount of energy the motor needs to spin the disc with magnets on it will always be greater then the amount of electrical current being perpetuated by the electric generators on the water wheels complements of natural energy losses do to heat and friction. This assumption is understandable however I will explain why this does not stop this device from being an over unity device. You see it comes down to one simple truth. The motor spinning the vertically positioned disc is only actually doing a fraction of the needed work, it is the horizontally positioned magnets impacting into the tubes causing them to spin that is doing the heavy lifting :) and since the magnets are positioned horizontally on disc the push back against them is unable to hinder the motor spinning the disc to a degree that would require it to do loads more work. In conclusion this is a device that can be self contained away from the elements so as to not hinder it's effectiveness. And it is an Over unity device if built correctly. & to all you nay Sayers out there I would just like to add I hope you all have a great day and whether you like it or not this design works. :D

[@umaraziz704]

u hv knowledge bro hood job

[@linuxonbute]

If you can show it working for hours or days without editing the video I would believe you. If you watch the top basin water level you will find it is getting lower and lower proving as usual it isn't over unity. You know that is true just as we do. So it doesn't work. Nothing we can make is even 100% efficient. For this to work it has to be over 100% efficient to get any useful output.

[@ON____AIR]

Самое главное - запутать физику) За Дью!

[@sddiymakeitworthit7512]

Nice presentation and awesome 👏 workpiece 👍

[@kinghomemade]

Thank you

[@electromax7846]

Can not be 8KW, This setup may create max. 300W power

[@jeancarlof5717]

maybe 8kw a day

[@bernardthongvanh5613]

@@jeancarlof5717 kw is a per second unit, so 8kw a day does not make sense

[@andrey2332]

30w max

[@necaton]

@@bernardthongvanh5613 has nothing to do with seconds but ok

[@morsalinsifath1752]

@@andrey2332yes max 25-30 W

[@Shine___10101]

This is a great project! The comment section offered a lot of suggestions on how to improve the project, too, it's very insightful. Thanks!

[@notamouse5630]

To get proper power out of this: 1) add iron powder to the epoxy. 1a) make the steel in the casing 5mm thick to support the magnetic loading. 1b) full welds, not tacking. 1c) proper axial bearings, radial will not support the permanent magnet load. 2) A full bridge rectifier and a grid tie inverter is required to reduce the overspeed concern. 3) an emergency load for truly excessive overspeed. 3a) Can be in the form of a voltage controlled shunt: MOSFET switching a quartz bar heater on the DC bus with voltage divider can do this.

[@alfonsomolinarobles5295]

Nice job and nice design congratulation, but is a shame how you tried to fool people with the result. With 4 coils and with those RPM you did not even generate 50 mA. Still, good job keep trying.

[@kinghomemade]

thanks for your intention

[@hasanchalabi]

Yeah, he is trying to fool but amazing as you said again bro

[@premilabarathod6173]

He is making fool.... It's not possible with this speed.... Output he is showing seems to be cheated

[@mike289homebuilt5]

Powerful generators have heavier guage wire, 12 coils on each side of a central rotor in 3 phase, but building a larger one it would require speed regulator and brake

[@suparnobolang3685]

Aku suka sekali nonton video ini sangat bermanfaat untuk menambah ilmu saya terimakasih videonya kak.... 👍👍👍

[@greenaum]

The power rating of the pump he uses at the end as a test, will be the rating when it's under load, actually pumping. That will vary, too, according to how high it needs to pump the water. Free-running it might well only use a tenth of it's rated power. The fan is tricky, because a fan turns too quickly to be seen on video normally. So we've no idea how fast it's running, and therefore how much power it's getting. Probably this generator's coil windings are a good bit thicker than the ones in the fan's motor, so it's more powerful than that. Of course the blades are larger too, though the rpm is much lower. Would be difficult to guess at which would push more air, if the generator was wired up as a fan. Actually that might be a good demo / test. Power the generator, using it as a fan. Use the shop-bought fan as a comparison. Have them facing each other, and see which way, say, a piece of dangling string is blown. The idea would be to see which fan is stronger. From that, you could reasonably assume how much more powerful the windmill is than the fan. Since a motor and a generator are the same thing, the only difference is the specifics of fine-tuning it. Failing that, just have the windmill power a kettle and see how long to boil 1 litre of water, or to heat it by 10C or the like. Even better just stick one of those plug-through power usage meters in. Like the Hopi that Big Clive uses. Sorry I just saw the fan and got carried away. Regardless, nice build. The practical thought that went into making what he wanted from the parts he had is impressive. I hope he gets a lot of decent use out of it. The coil winding machine is nifty, I suppose he calculated beforehand, what sort of rpm he could expect, and what voltage he wanted, to know how many turns to use.

[@oswaldoriginal5037]

I think this was a SCAM video

[@prinegonbevaris1788]

We can make some assumptions about what output his generator is able to make, since he did the test with the lampbulbs. I don't think, those bulbs are using more than 60 watts, but let's be generous and assume, they are 100 watts each. We can only see them glowing a short period of thime, when his generator was spinning quite fast. As soon as it begun to slow down, the light was flickering off. Altough after the blades where installed, the generator was spinning constantly, but clearly slower than what he was spinning them with his hand before. Therefore we know for a fact, that he is producing less than 300 watts. I think, if we assume he produes 150 watts, that assumption would be fair. Eigher way it is impossible in my opinion that he would produce enough power to run the fan, let only the pump at the same time, so something fishy is going on here.

[@oswaldoriginal5037]

@@prinegonbevaris1788 we are experience youtubers and we can spot a fake immediately

[@joelopilato6625]

@@oswaldoriginal5037 I think that you're correct... IMHO, He doesn't have enough poles to generate the power requirements for driving a fan and a pump... The power poles in the background give it all away... His creativity is not in the design, but in getting the views which makes him money...

[@GWTechHD]

@@oswaldoriginal5037 I think so too

[@muhaimuldimas4955]

For DIY this is awsome.. I suggest you learn about airfoil etc to build HAWT or VAWT

[@the3dhermit]

When cutting on a tank that held anything that was remotely flamable or explosive, remove the valve, and full the tank with water first, to make sure there are no fumes left in the tank to ignite.

[@adammathieson1428]

Great work. Please, next project, fabricate a guard for that grinder before you cut your fingers off cutting up waste pipe.

[@TuckySlim]

I know right ! I have great safe tools and safety gear... And still have had 2 horrible finger injuries from my angle grinder.. I was cringing lol

[@vipproduct375]

20:20 ❤

[@evgenyrogov1384]

fake, ровная работа насоса на 50Hz от рваного вращения генератора, но прикольно смотреть как без всяких подгонок ровно приварено без биения и с идеальным балансом ))

[@frodosymkin7733]

НЕ ВЕРЮ!

[@n.8337]

Странно что никого не смутило отсутствие стальных сердечников в обмотках. Такая схема работать не будет. А была бы сталь, было бы залипание магнитов, соответственно вал бы так легко не вращался. Видео на лоха.

[@andriik6788]

@@n.8337 Прекрасно работают генераторы без сердечников - их используют как раз частенько в самодельных ветряках, чтобы избежать залипания.

[@n.8337]

@@andriik6788 магнитного поля внутри катушек возникать не будет, а следовательно и эдс. Физика 7 класс. Вы хотите мне сказать, что вал без магнитного залипания будет легко вращаться и вырабатывать сотни ватт мощности? Генератор под нагрузкой не легко провернуть. На каждый выработанный ватт электроэнергии нужно затратить больше ватт механической энергии, это связанно с КПД генератора + потери на нагревание проводников

[@andriik6788]

@@n.8337 С чего бы ему не возникать внутри катушек? Воздух магнитное поле тоже проводит, не только металл. Вал без магнитного залипания будет легко вращаться БЕЗ нагрузки, естественно. Под нагрузкой - с усилием. Тем не менее, не будет эффекта залипания, что облегчает страгивание винта на не сильном ветру. Наличии/отсутствие сердечников влияет на размеры генератора, а так же на то насколько велика должна быть скорость вращения. При наличии сердечников можно сделать генератор меньшего размера и более тихоходный. Но для самодельщиков это не критично - они могут просто сделать генератор под их задачу.

[@inhibited44]

I wish my electromagnetics prof at UNH years ago 40 years ago had us build something like that to show us the principles. The class was just books. I remember there was some equation concerning the voltage or power that was dependent on the number of turns of wire. I got a use for something like that. I might adapt it for a project. You must have put epoxy on the coils to make them stay together. I took four EE classes at UMass Lowell and the professors there said principles of how to make a motor wouldn't be seen until grad school - lol. There is another guy, Jeremy Fielding on youtube that loves motors too.

[@СергейВайс-э8ш]

Ну ты даёшь индеец. Я балдю. БАМ,БАМ,БАМ!👍👍👍👍👍👌

[@ГеоргийФедорович-у9с]

Компаунд понравился которым заливал вроде не эпоксидка,насчет 8 киловатт сомнительно,один или полтора кило не больше.

[@AHAMAY]

@@ГеоргийФедорович-у9с да какие уж там полтора киловата)) Ассинхронка 370ватт у него в холостую работает и то оборотов в 10раз меньше номинала. А если и рукой тормознуть шкиф то и вовсе остановится. Ватт 100 не больше

[@automobailenthusiast]

Amazing Bro nice👍👌

[@kinghomemade]

Thank you very much

[@dalnuu7425]

The man 👍

[@alpeshkmakvana7379]

Very nice lovely from I am (INDIA)

[@Ecksterphono]

You should have used 3 iron cores for the stator for better inductance. Plus use a rectifier for smoother performance. Not hard to make or purchase. A capacitor as well so it can store electricity and even out the fluctuations

[@kinghomemade]

thanks for your comment

[@rayhan-420]

Please tell me what's iron mm used

[@Ecksterphono]

@@rayhan-420 basically the iron core should be laminated and ground to that triangular shape and then put the pieces on a jig one wrap of rough electical tape and then wrap the windings around that. Insulation has to be good.

[@PappyDan]

good start, single phase, next time 6 coils, and full 3 phase, clean up the raw dirty power, in to a clean 60hz of power.

[@taffydubez4312]

I think this video is useful to beginners. We all know a lot is involved in making a perfect turbine.

[@jimjakosh2506]

You need to add details of the wiring of the coils, the angle of the blades and the output of the windmill. I take it is DC voltage. What is it used for? Is it run to batteries through a converter or run through an inverter into the grid????

[@mookyzook]

With moving a set of equal coils (300 turns) past a set of magnets north and south it's bound to be AC the Hertz depends on the wind speed. Basic electrics! He shows you how to wire the coils and connects it to a 240v ac pump, simple! All your questions are answered by actually watching the video. It's a pretty clever little unit, helped by this guy's very accurate measuring and welding.

[@neurotik69]

@@mookyzook yes you are correct, i am Reading so manu bullshits, ofc this system from an electrical point of view sucks, to be complete you should add recrifier-optional Energy storing system-inverter, the inverter Is a must because as you said the wm (Speed of the blades) Will be equal to we (Speed of the current vectors) but normal house Electric powered appliances are built and work with 60(America)50Hz(Europe) so this Is a cool and entertaining DIY project but Notting more

[@osmanghazi3215]

I think that he make the combination of solar & wind energy which make possible to run the heavy load even the pump. You should store the extra energy and keep it up bro 💯

[@aghaazhar9048]

Nice fabrication 👍

[@stevo1997gong]

Probs shoulda mentioned not to cut a gas bottle with a grinder. Wow that’s a new level

[@davekavanagh7599]

Fill the tank with water first, pushes out all the gas, then you can cut. Maybe educate yourself before running your mouth 👌

[@tommycabanaw4875]

I mean non flammable gas

[@danx6327]

Hay muchos errores y dudosa credibilidad la sección del alambre y el numero de vueltas es insuficiente para generar esa tension ,el devanado sin un núcleo tiene un pésimo rendimiento y además esta restringido el campo al ser blokeado por la tapa metálica ,el brillo de las lamparas no se acompaña de forma proporcional al giro que le da con la mano al rotor lo que hace sospechar que están alimentadas con una fuente variable ajena al generador ,las paletas no tienen superficie alar sino que son toscamente planas y tienen bajo rendimiento,la corriente de aire nesesaria para provocar un giro de unas 100 rpm seria como la de un uracan y de forma sostenida y no pequeñas corrientes de aire intermitentes como se da de forma cotidiana ,la carga conectada genera una resistencia mecánica al giro del rotor así que quedaría frenado si colocamos una lamparita de linernaa pilas

[@josem1799]

Hay fiasco evidentemente!!!!!

[@LuisJSFilho]

Sim, exato! Também percebi que havia muitos erros de projeto neste vídeo.

[@albertoramonacosta1212]

Ya no sebexpert opinan y solo queda replicar y comorobar quizas no da los watios q dice cuatro mil es una masa de hierro o silicio grande quiza otirgue 400 watios para arrancar un motor de 0.35 y un ventilador

[@ricardoaniballosadaherrera3690]

Efectivamente es una falsedad

[@LuisJSFilho]

@@ricardoaniballosadaherrera3690 si!

[@felixmarquez6791]

I love looking at this kind of stuff.

[@zajomizxn362]

It was easier if you cut strips of the metal sheet to make the rings. you didn't damage the first object.

[@engineerkohat]

Another genius.

[@M.i.n.e.c.r.a.f.t.e.r_yt]

Very genius 👍

[@keepingit_real5005]

Maybe 8000watt per day? Anyway that is an awsome design and made very well. AAA+

[@emiliorp786]

Es el mejor video que e visto sobre construcciones de aerogeneradores.

[@hansonigor]

Fantastic skills with tools and metal! Though, doubt it is more than 600 watts

[@westellmodel]

Which if you store on a 5kwh battery you can power a house.

[@westellmodel]

If he added a flywheel to this it would work as a mechanical battery and help with power fluctuation too

[@manuelrojas1839]

Excelente trabajo, Muy ilustrativo. Me hubiese gustado que mida el Voltaje y también Corriente en Amperios.

[@c.g.g.m1201]

Si así fuera, el título del vídeo quedaría como fraude, porque no genera 220, sino 12 Volts, es un alternador rudimentario.

[@alocin110]

Excellent project. Very smart engineering. Thank you for sharing. I liked your video. Keep up the good sharing.

[@j_s_projects1426]

Nice job, make video with connected Multimeter.

[@TheeeDannyD]

This is brilliant! Particularly love the flattening of the pvc pipe! I am gathering info to try make a smaller turbine with a gear system to create more spin that will use the air coming in my car to try power small gadgets.

[@tranhoaitrungmusicofficial6626]

Bạn thật tháo vát, tìm tòi sáng tạo, điện gió sạch đang là vấn đề hot toàn cầu, cám ơn bạn đã chia sẻ!

[@a.vinodkumar6709]

U should change blades to vertical , I think load runs on solar energy, but great job

[@СергейДмитренко-ш9е]

Такой генератор зажгет разве что 12В лампочку... Ни о каких 8 кВт там не может быть и речи.... Максимум 80 Вт и то при хорошем ветре.... Это Фейк!!!....

[@Jafar-Sadik]

You produce a great science-fiction content for people with no scientific background which is I guess 99% of our society. Good job.

[@mawkleeforest9814]

Good work and handy skills. However, power generated is doubtful. The water pump motor is runing very low speed. Could you check the frequency

[@mistar-t]

it is mistake

[@ronalddaub7965]

3 Hertz up to 80 cycle s without a governor or some way to control it what does it do with a big load?

[@ronalddaub7965]

I want to see the windmill run the welder that he used to build it.

[@theilluminatiresistance]

I gues one would need a transformer to get an even amount of current flowing

[@rinath8210]

Даже если самоделка работает, она крайне не эффективна, так как надо было собрать трехфазный генератор, а не однофазный

[@АлександрКоваленко-с5р]

Она не работает, это фейк.

[@СергейЧерешнев-н7м]

Если у вас есть возможность разместите ссылку рабочего агрегата. С уважением Сергей.

[@СергійЄрмак-о9з]

Вот ссылка на канал ,где человек делает самые разные генераторы и ветряки. kzbin.info/www/bejne/jnnSpIZoqJ6rY8k Этот аксиальный генератор выдаёт 1 кВт при 500 об/мин.

[@СергейЧерешнев-н7м]

@@СергійЄрмак-о9з Благодарствую за участие и помощь. С уважением Сергей.

[@reveal-lk6ip]

Возьми обычное мотор колесо от электросамоката или скутера, и приделай к нему ветряк - толку будет больше!

[@vincenttelfer4206]

King has talent, you could charge a lot of vehicles or bikes and your home. Ev's and electric bikes should have replaceable battery packs available locally

[@vladimirsamas3097]

ah this is fake not 8000W but 80w

[@vincenttelfer4206]

@@vladimirsamas3097 , technically it could be 8,000w outgoing, after charging some lipo's or super caps. Consider the amps, rpm's and the wire size, gearing the windmill would help a blade adj. with wind tracking like solar tracking and height. I have a project for king

[@vladimirsamas3097]

@@vincenttelfer4206 yes li po + caps for 2min 8000W but this generator mak very low power li po is dc 220V is ac no convektor ;;; plus is totaly fauls the blade dont spin at 50 hz.... the problem is than on YT i;...... sry for bad uk

[@ednagettobed5793]

Nicely done.

[@lathalatha-qo6tu]

டடடடடட

[@SardoR_rec]

Вытащить 1кВт из такой игрушки да еще при таких оборотах лопастей... Это что то из мира фантастики :(

[@varman001]

I don't know where all the commenters got the idea this generator puts out 8000 Watts. It says 1/2 HP on the motor label, which is around 370 Watts!... and yes... it makes sense.

[@Elcosmicstar1]

It makes absolutely no sense, go back and study your basic, I mean really basic electronics and you would see it is utter rubbish he is trying to sell us, come on man, for starters, the generator blades are turning at 3 revolution per second (3 hz), this is a 50 hz pump. This is riddled with flaws. And as far as the 8000 watts is concerned, what part of 8000w don't you understand? Did you read the advertised photo? YES!!! that is what he is advertising, THE PUMP draws 370 watts, this has NOTHING to do with the generator output. Does an appliance power consumption in your home determine the total power delivered from the electric company? Does the appliance you plug into your outlet determine the maximum power that can be delivered from that outlet? A 120 volts @ 20 amps outlet in your home can support up to 2400 watts, but that does not mean your blender consumes 2400 watts. Go and remove your comment, it is making you look stupid and the people who agreed with you and in future, avoid commenting on topics you don't understand for your own good.

[@tomconner5067]

From my experience with air boats, pancake cages and Ivo props, I see one issue under heavy winds while supplying a high demand, the thrust movement of the impeller ends may contact the mounting pole, unless you used very rigid mandrels for the blades. I would have accommodated for tip pressure migration as an instinctive measure, but I'm used to 3-700bhp with 350-900ftlbs of torque doing the twisting.

[@omarriosgaona9352]

Y

[@НАТАЛИТернова]

Дуже дякую вам . Ви майстер на всі руки

[@enos4819]

É falso, os eletrodomésticos não tem queda de energia, isso não aguentaria ligar tudo isso, no máximo um equipamento

[@kunjandave5526]

बहोत सुन्दर कला भाई आपका कल्याण हो 🙏👍👌😁

[@abdullahnaggar]

Good job Wonderful and beautiful work Thank you I am from Yemen

[@joseeduardocamposguzman2081]

Si entregara 10Watts reales, me quedaría impresionsdo.

[@marioadiez]

Para entregar 8 Kw el largo teórico de cada pala debe estar por los 5 metros, o sea una turbina de 10 metros de diámetro!

[@kurniawan7162]

Ini numpang tanya, untuk membeli alat penggulung dimana ya.....?

[@krishnaprabhas6737]

Nc

[@mickgatz214]

I appreciated your project very much. from Australia.

[@InsideTraderNancy]

It's bogus dude fr. Magnets were improperly placed and even with current conditions it'll produce 40 watts at best.

[@nakamuraka777]

I've learned a lot from this video..👍

[@fedeyoutub]

the only thing you can learn from this video is how easy it is to create fakes and make visualizations by fooling everyone.

[@tiberiolincoln5687]

Congratulation, Very good project.

[@kinghomemade]

Thank you so much

[@rasuljonizatulayev7362]

От ветра бежать некуда еще вентилятор включили хороший парень!

[@iamwholewithmysoul547]

If you would ever consider building them for human let me know cuz I would definitely buy one lol love it so creative

[@MuhammadSaleem-ef5vy]

Very good effort by you Your qualification please?

[@Ivan_grodna.]

Удивительные вещи делают люди , без точного измерения, получается точные и интересные изделия. Подшипники бы смазал.

[@tiagodemelo3500]

Faltou mostrar com o multímetro a tensão de saída...

[@devluinix843]

ele ligou 3 lampadas de ~60w da pra ter uma ideia, fora 1 ventilador junto com bomba hidraulica de 370w

[@tiagodemelo3500]

@@devluinix843 só q as potências não estavam descritas no vídeo.

[@devluinix843]

@@tiagodemelo3500 verdade. Mas a bomba Dagua tinha descrição no rótulo metálico e por ter ligado a mais ou menos 70% da velocidade comum já é muito impressionante. Chuto uns: ~190v ~1.6A ~300w (apenas no motor)

[@МихаилВасильев-ь2у]

Самоделка будет впрок, если дует ветерок!

[@thomaswomack3888]

considering the size of the wire in the generator coils I can't imagine getting more than a few amps of current. I would love to know the real output.

[@alla_alsayegh]

there is a black wire at 19:00 under the Turbine. it's really impossible to turn on a 10HP pump continuously without 60 ,or 50 hz sin wave and the Turbine has no reaction 😅

[@blackhatentertainments]

those are not 100W light bulbs , its just a 5W light bulb ,anyway its all fake

[@vtorsi610]

@@alla_alsayegh NOT 10 HP pump - It is a 1/2 HP pump ( 300 Watt ) under no load. But still, I am not convinced this is real

[@alla_alsayegh]

@@vtorsi610 if this is real he can sell power to countries, man not just upload a video in KZbin

[@mickgatz214]

the surface rust on the vice tripped me out! 😂

[@gerrygwag]

Great idea but I would suggest some kind of slip ring so the wind turbine can follow the wind direction without the possibility of wrapplig the cord around the pedestal.

[@randomx4289]

I was thinking the same.

[@gerrygwag]

@@randomx4289 It still works well though.

[@peterwiremuormsby9383]

Probably turns no more than 180degrees left or right so it would only need a little bit of slack in the cord.

[@gerrygwag]

@@peterwiremuormsby9383 Perhaps but it might get spun around. Wind is very un predictable.

[@peterwiremuormsby9383]

@@gerrygwag not if it's got a stop on it to limit it from turning more than 360 degrees.!!!

[@saulcaetano]

Why did you cheat at the end. Its a good project, but its impossible to stand with an electric motor and a fan.

[@davidfarage5252]

Okay very good

[@isahyusuf1368]

The problem why it cannot power those electrical alliances is that the speed of the rotation is too slow the best way is to connect gears and increase the turn of the coil.

[@Imtiyaz5power]

Yup...same here

[@ttose9292]

Same here

[@skliaw6127]

the magnetic field didn,t even cut thru the coil in the efficient way.

[@MrKlipstar]

Very smart,in fact. Mecatronics and domotics the future!

[@Misthema]

Here we are, witnessing the power of the internet.

[@Sc-dn8dp]

Haven’t seen a fan like that in 40 years 😳

[@bradskinner3574]

5 coils 4 magnets will prevent breaking bro, awesome video

[@aux1z11]

Can you run a 220v 5hp table saw on this and a drill press and a air compressor and air-conditioning all at the same time, By the way you can use a $14.95 worth of fiberglass resin instead of expensive epoxy

[@kinghomemade]

yes

[@Soneroğlu]

Very Nice system bro..you must do it vertical turbine

[@LuisDiaz-xg2gu]

Buena forma y fácil para obtener energia eólica. Felicitaciones 😊

[@Redwiat]

His Father: We don't need company's electricity. He: 😎

[@azimbakan3160]

👍⚡⚡⚡

[@azimbakan3160]

GAY😂

[@xyzxyz4575]

he just need a LiFe battery to store power!

[@John-NeverStopLearning]

Great skills!! How did you get the wiring from the rotation of the generator down the pole without having the wires twisted until they break?

[@armands9991]

The stator with coils and wires coming from them are stationary thanks to the bearings, only the magnet plate is spinning.

[@ingeniando8096]

Debes hacer revisiones periódicas, al menos una vez por semana, y desentorcharlo manualmente antes de que se llegue a trozar el cable.

[@texasRoofDoctor]

That was fantastic. The best part may have been the "propeller dance" where you flattened the blades. Keep up the great work.

[@alexfox8944]

no! its fake!

[@texasRoofDoctor]

@@alexfox8944 the dance or the whole video? The copper wire spooling looked convincing.

[@alexfox8944]

@@texasRoofDoctor whole video

[@texasRoofDoctor]

@@alexfox8944 copy that. Let me know if can think of a KZbin video that shows how to properly do something similar.

[@alexfox8944]

@@texasRoofDoctor kzbin.info/www/bejne/faXFkqKXfteAmc0&ab_channel=%D0%AD%2B%D0%9C