Kitchen Faucet Leaks at the Base. Easy 5 min Fix

Link to Universal "O" ring set.
amzn.to/3ElQYrF
This link also shows how to measure the o rings you need for your specific faucet.
Here is a link to a small tube of lubricant. It is a good idea to grease the seals when you put it back together:
amzn.to/3t4TT1w
If you have a Single handle faucet that leaks at the base where it swivels. It is an easy 5 min fix. The O-rings that seal the neck only cost about $2 and it something that you can easily fix yourself. The faucet in the video is a Price Pfister Brand. but most single handle faucets are similar. In this video the faucet uses a cartridge system. if you have a faucet that uses a ball with springs and seats (old delta style) than you will need to shut the water off. follow this link to see how to repair those.
• Fix a leaking Delta Fa...
Key Words:
fix, leak, leaking, kitchen, Price pfister, seals, drip, dripping, moen, aqua source, sink, kitchen faucet, how to fix leaky faucet, faucet repair, how to fix leaky faucet, how to fix leaky faucet handle, how to fix leaky faucet in bathtub, how to fix leaky faucet single handle, faucet, how to fix, leaking kitchen faucet base, leaky faucet repair, leaky kitchen faucet, leaky faucet, kitchen faucet leak repair, kitchen faucet leaking at base, leaky bathroom faucet, single handle mixer tap
“As an Amazon Associate I earn from qualifying purchases.”

[@worldofnature6731]

Thanks for this video. I was able to take apart my tap this morning with your help, and discovered a lose fitting. I was able to fix it by simply tightening it up. I love the music too :)

[@aznation4592]

So you didn’t have to replace those black rubber rings ?

[@worldofnature6731]

@@aznation4592 No, I did not, I simply tightened up that top brass nut. It has been working flawlessly ever since I did this too. I did install the faucet myself, and think the nut just might not have been tightened enough from the factory.

[@aznation4592]

@@worldofnature6731 Awesome thanks for the response

[@worldofnature6731]

@@aznation4592 you are welcome :)

[@stevendreith4343]

Thanks for keeping this video under 30 minutes. Very direct, and helpful.

[@SkyManagement]

Glad it was helpful!

[@unclefred6119]

A BIG "10" for explicit repair directions! Thanks for this video. Will tell others about your channel!

[@SkyManagement]

Thank you so much! We appreciate the support :)

[@agamomma]

I appreciate learning about this fix and I also loved the music! I could watch it through to the end and i didn’t feel irritated. 😂

[@boardcandidates138]

one of the best videos on youtube. stunning. note: my o-rings didn't fit, however vinegar on the calcium deposits and some grease did the trick... for now.

[@SkyManagement]

Thank you for the support :)

[@palefeathervaldez3563]

Thank you so much for this fix it video, the leaking water from my kitchen faucet was driving me crazy, didn't know what to do I use to have to put rags around the faucet for the leaking. I made my husband come watch this video so he will do it tomorrow. Thank you, Thank you.... :)

[@SkyManagement]

No problem! Glad we could help! Thank you for supporting our channel :)

[@nikobitan7294]

You should try fixing it yourself. It's nothing you couldn't do yourself.

[@Alan-gh8X]

What f**k is a faucet or are you meaning forceps.

[@jermainewindham6024]

Wow! Great video. I just noticed my exact type of faucet leaking this morning. I just order the o-rings from Amazon. I plan on repairing the leak whenever the Amazon order arrives today. Liked and Subscribed 😊

[@SkyManagement]

Awesome! Thank you for the support :)

[@jangrigsby7480]

Thank you so much for your informative video! I was able to fix the leak in my rental duplex for my tenants. . . . .and save myself a plumbing bill!!

[@sigridohealaigh1512]

Thank you for the video. Great job!.....I am a female and think I can do this lol :) And I love the classical music along with it....Crative!

[@ccroy2001]

A great help! The process was straightforward, but I found no branding at all on my faucet. I had to buy a 7/64" hex key and channel locks, then measure the O-rings and guess. First guess wrong, 2nd was right and the package says for "Delta and Peerless Faucets". Hope this helps someone. So nice not to have a leaky faucet anymore!

[@lenadesousa9492]

Why is the part a person needs to n replace when neck of kitchen that connects to base. does no swing back and fourth. smoothly

[@ThuLe-eh1xe]

I like Mozart music. Helps me feel less stressed. Thank you for the simple instruction

[@SkyManagement]

Thank you for the kind words! Always happy to help :)

[@FoodPornNetwork]

I just replaced the cartridge hoping it would fix this problem, nope, now I will fix it thanks to you!

[@SkyManagement]

Glad we could help! With a new cartrage and O-rings, you should be good to go for a while :)

[@FoodPornNetwork]

@@SkyManagement Thanks yesI need the o rings and life will be looking up!

[@michaelstoliker971]

Thanks for the video. I thought the leak was caused by the ball valve. I bought a ball valve kit when I should have bought couple o-rings.

[@orion1983uk]

Thanks for uploading this. My tap looks similar to this and is leaking in the same place. Will give this a go!

[@SkyManagement]

Glad we could help! You may want to take the old seals off first and take them to the hardware store with you to make sure you get the right size replacements. They do come in a few different sizes. Thanks for watching!

[@XanderRowlet]

First time homeowner, the leaky faucet was driving me mad. Thanks for the help. Kitchen faucet is bone dry now

[@SkyManagement]

That’s what we like to hear! You are now a pro!

[@kretonslovechild7999]

Just fyi, before buying new o-rings check to make sure yours didn't just come unseated. This was the case in my Moen single handle faucet. The o-ring had partially come out of the groove of the plastic piece it sits in but was otherwise okay. I suspect pivoting the faucet from one sink to the other unseated it over time. Reseating it fixed my leak.

[@joeyd3324]

Not exactly what I needed but led me down the right path...Thanks Bud...

[@SkyManagement]

No problem. Glad we could help.

[@bankimpandya4648]

Great video!! It helps with quick steps and good music too! Thank you.

[@SkyManagement]

Thank You!! Glad it helped!

[@chrisschmieg8373]

Just taking apart the tap and tightening the Cartridge Nut worked for me.

[@deep_fried_midget]

Worked perfectly. Thank you. I wish i had put some plumbers grease on there though, just to make the spout easier to lift off next time.

[@ericsanmiguel8898]

Thanks a lot sir... You helping lot of people by solving our problem.

[@SkyManagement]

No problem! Glad we could help :)

[@shaundburch]

Thanks so much! Just working on one of these today. Thought it was the cartridge but it's still leaking. This should do the trick!

[@SkyManagement]

Did it work? Awesome! We appreciate you more than you know!

[@KrystalHorizon]

The music, makes it feel less daunting! Simple and detailed. Thank you for this!

[@craigtee8832]

Thank you! I was afraid to take the pliers to the collar until I watched your video. I KNEW something had to be holding the neck down but couldn't see what it was. Thanks again.

[@SkyManagement]

Glad I could help!

[@johncyples6343]

Excellent video. A washcloth under the pliers would prevent scratches, but very good. Tks

[@craigtee8832]

@@johncyples6343 Good point! I used a scrap of old inner tube I had sitting around. Worked great!

[@fh3486]

I took mine off as instructed and just cleaned the casket off because years of build-ups. I put it back and no more leaks. Just make sure you use a a towel to wrap around the bottom piece when using channel lock. It will scratch the metal finish. Other than that I did it

[@SkyManagement]

glad we could help!

[@timulman715]

Great video, excellent choice of music!! You've got another subscriber. Thanks much.

[@SkyManagement]

Sweet! We love the support! We will try and make some other great videos.

[@manpreetsidhu9017]

Saved me some money 💰 thanks

[@tonycarlton2029]

I installed a new faucet not too long ago, very similar to the one in your video. It started leaking bad out of the base. I watched your video and then took my faucet apart. I noticed that plastic ring was below the neck instead of inside the top of it. Am thinking maybe I installed it wrong. Going to try that ring on top and see if it helps. If not then I'll replace the rings. Thanks for the great video!

[@SkyManagement]

No problem. Yes… rings should last a while. You can help them along by adding some lube but being new I wouldn’t expect it to be necessary

[@staywoke1474]

I was getting ready to call the plumber till I came across this vid thanks a lot it was just a loose fitting

[@SkyManagement]

Glad to hear! Stick with us! We have several great videos. Anything you want us to help with? We would love to hear ideas :-)

[@big_brother_is_watching_you]

thank you sir, saved me time and money

[@SkyManagement]

No problem! I’m just glad we could help.

[@pjamajones8304]

Nice easy steps to see...Bit concerned multigrips would bite and scratch chrome collar though

[@SkyManagement]

Yeah, they can. A lot of the time I will wrap a towel around the top before I grab it with the pliers.

[@yourmomisanicelady8186]

Awesome. I have the same faucet. Thanks

[@SkyManagement]

No problem. Glad we could help!

[@QUABLEDISTOCFICKLEPO]

Looks easy I'll try tomorrow.

[@SkyManagement]

You can do it! We believe in you. It’s a good idea to turn the water off first if you are unsure what type of faucet you have. And although it’s not shown in the video, we would recommend using some grease on the o-rings.

[@QUABLEDISTOCFICKLEPO]

@@SkyManagement Okay, I'll add some Plumber's "grease."

[@palefeathervaldez3563]

Nice and simple fix, thanks.

[@doccock1662]

I followed this video’s advice without turning the water off and it spewed water all over my kitchen!!!!!!!!FUUUCK!!!!! My entire tap disintegrated.

[@polson8084]

Love the music!

[@SkyManagement]

Glad you like it. Some like talking... others... music. :-)

[@normancecilnealjr3111]

Hey it was real good and helpful mom is just a different brand and older and I was just kind of just hard you know how it is hell can you have it all but I thank you though aren't sitting everyday brother take care

[@SkyManagement]

Glad we could help! Thanks for supporting our channel.

[@markhoward6347]

Very helpful. Love the music.

[@jimacheson4933]

Thanks for the great video. All my parts usually end up dropped in the drain, I spend more time fishing them out than the time to change the rings. 😂

[@SkyManagement]

Haha. Yeah. I’ve been there. 😂

[@brohick8868]

I take a paper towel and just lay it over top of the drain. That way if I drop anything it won’t go down the drain. It makes life much easier

[@VaQm11]

This was amazingly helpfull, thank you!

[@SkyManagement]

I'm so glad!

[@Alaska610ish]

That was an awesome video! Thank you. Wish I could tell what brand we have.

[@mwestaway211]

This is a very helpful video! Thanks

[@SkyManagement]

No problem :) glad we could help!

[@forestgubs6389]

Luv the watch.

[@peachdaisy3478]

The music makes it even more epic

[@SkyManagement]

Thanks. My brother likes the videos where we don’t talk. I tend to get long winded.

[@panzerabwerkanone]

Eine Kleine Wasser Musik? Sehr schön

[@pookiecatblue]

Great video. Thank you.

[@kennydieu2694]

Thanks for sharing .

[@SkyManagement]

No problem! We are always happy to help :)

[@tawnyjones1]

Love the music.

[@SkyManagement]

Thanks! I find it kind of calming. I know the classics aren’t for everyone... But that’s the beauty of the mute button. 😂

[@EnchantedSmellyWolf]

If only sink was designed this easy. Mine is cryptic.

[@SkyManagement]

Yes there are some brands that are not as easy to work with to be sure.

[@IMRANnet]

Great video.

[@SkyManagement]

Thank you! Glad we could help.

[@txtabby]

Good vid. Like the music too! Should of done more prediction value for more fun. More pointing, more thumbs up. Lol👍🏼

[@SkyManagement]

Thanks for your support! We are still pretty new at this, I appreciate the advice :)

[@tomascapone164]

How come you didn't use the recommended silicone grease on the O-Rings? The faucet will rotate more freely and smoothly, resulting in not tearing up the dry O-Rings.

[@JohnDavis-yz9nq]

I always use a wipe the inside of the neck of the faucet with petroleum jelly before sliding in back on.

[@SkyManagement]

Yes! If you have it with you, that would make things slide smoother. I agree.

[@JohnDavis-yz9nq]

Sky Management slides easier and protects the rubber O rings. Also I don’t think it would hurt to put regular pipe dope on the O rings. Plumbers always say if in doubt dope it.

[@leochou7022]

applying "Faucet Grease" is a safer option.

[@JohnDavis-yz9nq]

Leo Chou pipe dope.

[@gives_bad_advice]

About the only good thing about the internet are fix-it videos.

[@SkyManagement]

Glad we could be that something … for you!

[@anthonymarroquin1952]

Awesome

[@alexxlify]

Very helpful! Thanks!

[@michaelhelton2394]

me thinks you should put a food grade grease on rubber o-rings, and also might put a cloth around chrome piece before putting channel locks to it

[@creativegirl9710]

Your right. Other videos suggest that grease/oil/lubricant.

[@MrNizamusa]

thanks

[@jaynealrowton1025]

Awesome Video, thank you for posting!!!

[@SkyManagement]

No problem! Thanks for watching and supporting our channel :)

[@bridgetdavis9752]

Bravo! Thank you!

[@SkyManagement]

No problem! Happy to help :)

[@DavidGonzalez-pi5hj]

Thank you!!!!

[@SkyManagement]

No problem. Glad we could help!

[@korosensei4384]

Bought a new faucet because the plumber said this cant be fixed. I wish I watched this vid earlier.

[@jackieurueta3547]

I was told the same

[@stevee7774]

Y’all need to find a new plumber.

[@ochachaway]

Nice straight forward video. Curious as to why I have to replace the top seal before the bottom one though?

[@SkyManagement]

You don’t have to. But, when rolling the o-ring down if you put the top one in first, the bottom one can roll over the top of it without getting stuck in the groove. Probably more important when removing them. If you do the bottom one first, it can pass over the top one. Without getting stuck in the groove and have to dig it out again.

[@musicloverdavid]

Some Mozart for your plumbing job

[@SkyManagement]

Oh... you know it...

[@Sketching_Science]

I’m getting water at the base as well as below the sink - should fixing these o rings fix both of those issues, or is it likely that I’m dealing with a bigger problem?

[@beautifulbluebird3238]

Awesome!!!

[@SkyManagement]

Glad we could help

[@derrickoliver3835]

Thanks 🙏 a million you’re dope!!

[@jrry660]

I could not remove the neck on my American Standard faucet. I tried to pull it off and thought I was going break it off the sink. As usual, these videos make things look simple, but in reality they are not. I will call a plumber to R&R the seals.

[@stevee7774]

It ain’t rocket science.

[@saviorgm7413]

I believe most people add some silicon grease to the O rings? Thats what i ve seen in other like videos

[@dancelep]

I wish we could see the other side where the taking things apart actually happens. I have a faucet like this, but I can't see any sort of red thing to pop off. So tiny, which I could see what it should look like.

[@larkenbradley6704]

Thank you very much. My husband has one question: "How do you get the hex key into the hex screw on the back side of the faucet handle? I can't see what I'm doing and can't get the key into the screw . . . .. Very much enjoy your choice of music."

[@SkyManagement]

It can be kinda tricky. It’s hard to see in the little hole. I’m not sure I can help very much… you have to have the right size wench (not all faucets are the same) and then just kinda feel around for it. 🤷🏼‍♂️

[@larkenbradley6704]

@@SkyManagement Thanks very much. We'll try, try again.

[@VicVinegar84]

@@larkenbradley6704 There’s always the possibility that the hex screw is stripped or so old and worn that it’s essentially apart of the fixture. If you have a small mirror, it wouldn’t hurt to use it to see exactly what the condition is. There’s always penetrating oil, that should help.

[@patrickcgreene]

I have a Price Pfister faucet myself. Looks very similar. Mines leaking above and below the spout connection. Took everything apart but I can't see to get the spout off. I yank and pull up on it and it moves maybe a 1/16" of a inch up and down but doesn't come off. I've tried tapping it up with a wrench and still no luck. The spout spins and moves super freely but no luck getting it to come completely off. I am still waiting for Price Pfister to get back to me with the model number and replacement parts as its under the lifetime warranty.

[@SkyManagement]

I have had them be pretty stuck before. I usually just wiggle the neck up and down until it breaks loose. I know that’s a real technical explanation. Lol. If that doesn’t work, you could try shooting some wd40 in there. To help loosen it up.

[@idottery]

Could the leak at the base also cause leaking under the sink? My base is leaking and also water dripping under the sink. I’m going to try the steps in this video and hopefully it fixes both my issues.

[@SkyManagement]

Yes! Most of the time we have to fix this issue it is because a resident has seen water dripping under their sink. Water comes out around the collar or “neck” of the sink and runs down and finds a way underneath . Ultimately dripping down below. If your sink has water coming out around the collar while on… this should take care of you! Good luck! 🍀

[@idottery]

@@SkyManagement it’s fixed! Thank you!

[@pauld205]

Great video! So you dont have to turn off the water under sink?

[@SkyManagement]

We would recommend Turing the water off. Especially if it’s your first time. If it’s a Cartridge style like the one in the video, then you technically don’t have to. If it’s the older style that uses a ball valve, then you will need to turn the water off.

[@gavinfoster9118]

What size Orings suit this size tap?

[@DaBeanz75]

Thanks! Made look easy, Helped Mucho! I liked the music. If NOT ur cuppa, then hit mute, LOL

[@DHYNETT12]

i like the music too : )

[@johnrogan9420]

The u tube repair never goes haywire...have seen complete truck engines on big rigs fried as the trucker does a "simple" lamp bulb replacement.

[@TheMainBoards]

Very good video. 100%%%%%%%%%%%%%%

[@susancastle5274]

I can't get the collar off with the channel locks. Any more suggestions?

[@SkyManagement]

Make sure the water is off in case you have a ball joint style, then you can tap around on the ring with your wrench or something to hopefully break loose any build up. Then if you still can't get it, you can use a pipe wrench, but I'd put a towel or something around it because it can tear up the finish on it pretty easy.

[@rhonda90402]

What would cause a Grohe Eurodisc faucet to leak from the bottom right after I cleaned it? There was some moldy-looking stuff where the faucet base meets the sink and I used a toothbrush to clean there. It leaked for a little bit and now stopped. Why would it stop leaking? I just fear it is going to start again. Thanks, in advance.

[@stevespanos75]

Good Job my man. Nice and simple, thanks a lot.

[@SkyManagement]

No problem! Happy to help.

[@michelebinder8074]

Ok, the hex screw is out. And now, the handle doesn't want to come off. I pulled up pretty hard. I'd just like to understand first what's keeping it together. It doesn't appear to snap in place, so maybe I won't break something by using more force. Good to know, thanks.

[@yellowsnomimosas]

Unscrew the collar first. He showed it in the video

[@mrih1586]

Liked, Mine leaks at the base like this one. Then drips into the cabinet below. Will this fix mine? It's a moen same design as the one in the video.

[@SkyManagement]

yes, its pretty common that a leak like this will end up inside the cabinet and damage the inside. this should fix the issue.

[@mrih1586]

@@SkyManagement Thanks for the reply..

[@ohger1]

"Moen" is Norwegian for "persistent leak"

[@SkyManagement]

Wow … I did not know that but it makes sense lol

[@jaysoulpurpose8782]

Very helpful...thanks!

[@SkyManagement]

Glad we could help! Subscribe for lots more DIY videos.

[@ptturboe5792]

That fix it if water on the outside of the wide base below? No water under sink?

[@SkyManagement]

Yeah, I would say this is probably a good place to start

[@spyrish]

What if it’s leaking at the base of the pressure lever? The handle for the water

[@SkyManagement]

it could be coming from the o-rings, or it could be coming from the cartridge. it would probably be a good idea to replace them both since you are going to have it apart anyway.

[@kellygannon9516]

The allen nut thing to take off the handle will not budge. Any ideas on how to get that to budge? I tried WD40 but still nothing.

[@SkyManagement]

I’ve never actually had one that I couldn’t get off. I guess if I couldn’t get it to move, you could drill it out. But then you would have to find a replacement.

[@zs5098]

Where do I get plastic cap on handle? Does anyone have a link?

[@nuffsenuff2890]

This is a very helpful video and I'm set to order O rings from amazon. I don't know what I'll do with all the Os that aren't a fit...make Christmas tree decorations? There is a whole lot of grunge where the plate meets, or is supposed to meet, the counter. in my kitchen I'm not sure if the tap is leaking or if it's splashing water that's causing it. Any ideas?

[@SkyManagement]

The link to the o-rings in the description shows how to measure them if you want to order individual ones in the size you need. We have multi-family properties, so having extras around is never a bad thing. Lol If you are getting calcium build up around the base, then i would guess it is probably leaking. Especially if you live somewhere with hard water, this is extremely common.

[@nuffsenuff2890]

@@SkyManagement Thank you very much indeed for this advice.

[@BEYEXI]

I’m confused I bought the o ring set u linked and they all seem to small even tho my faucet looks like the one is this video? Am i missing something?

[@SkyManagement]

It can be confusing which is why we linked a universal set that should cover most faucets. There are many single handle tap faucets that look “similar”. I would think one of the larger o rings in that set would work. They are meant to be a tight fit so you might need to stretch them over the top so they slide into the channels . When in doubt you can remove one of the rings and take it to a local hardware store and they should have something that would work. I’m sorry you are having issues.

[@jamesvoutour1866]

Yeah, turn the water valve off.. fixed my problem with 5 gal of water in my kitchen. Thanks sky. Never again.

[@dumpster1005]

Mine is leaking from further down

[@SkyManagement]

If it’s leaking below this all of the time (not just when the sink is running) then it’s probably time to replace the faucet. If it only leaks when it’s running. Then, try replacing the O-rings like in the video. They are cheap and May fix your issue.

[@elizabethfleming8818]

Think about how much more useful the start of the video would have been if you actually showed the side you were working on -I.e. had the camera facing the side you were working on. All I can see Is the back of your hand.

[@ghazaliwaqas6953]

How to open collar neck nut video please

[@SkyManagement]

First turn off the water at the shut off valves under the sink. Then, we use a pair of adjustable pliers in the video (you can also use a pipe wrench) to unscrew the collar. They can get pretty stuck on there over time. Sometimes it helps to gently tap on the collar a bit with the wrench to help break it loose.

[@QUABLEDISTOCFICKLEPO]

I just installed my Bilt Single Handle Kitchen Faucet With Sprayer.(I looks just like yours) It was surprisingly easy to install, BUT IT LEAKS BELOW THE SINK.

[@SkyManagement]

It’s hard to say without looking at it… if it only leaks when it’s running then I would check the sprayer connection first. If it uses the quick connect, sometimes they can be a little finicky if it’s not snapped on just right.

[@QUABLEDISTOCFICKLEPO]

@@SkyManagement It looks like you got it. It's difficult getting down there with my bad back, but I figured that you must know what you're taking about, so I made the effort to see where the water was coming from. It wasn't a leak, it was just water pouring unhindered out of the CENTRAL nozzle. So, it looks like I have to reconnect one of the hoses to the Central connection; then, I have to decide what to do with the...no, wait, the diagram explains. I was right to connect the hot and cold water lines to the two outside threaded cylinders extending below the sink. Then, the sprayer has to be connected through the central hole.. I will then have a sprayer. My old set-up had the hole for the sprayer plugged-up. and that was good enough for me. (Who needs a sprayer?) However, I have no objections to having one, and if my new faucet set requires that it be installed, so be it.THANKS A MILION!!! I THINK I CAN TAKE IT FROM HERE.

[@AshiteMiyavi]

What do you do when the collar neck is stuck? Mines is screwed on so tight I can't undo it 😫 plz help anyone 😔 😭 🙏

[@douglasbollinger3626]

At 3:50, when you slip the last o-ring on the top spout part, was that a new o-ring, too, or did you just replace the other two? (I know it's best just to replace all of them if you're repairing it, but was curious because I'm not sure my repair kit came with that third particular o-rings.) Thanks!

[@SkyManagement]

That ring is a plastic one. Some repair kits come with replacement ones, but it’s not really a seal. It sort of just helps guide the spout when you spin it. I typically reuse them unless it’s broken for some reason.

[@douglasbollinger3626]

@@SkyManagement I'll be fixing my mom's leaky kitchen faucet in the next day or two and appreciate the video and information. Thank you very much!

[@havefun2952]

So what caused the leak? The rings are not of the right size? I have a Moen kitchen faucet installed and in a couple of days this problem began to occur. After a few months, it has gotten more serious! The plumber did not admit this problem and said it is because I let water splash on it.

[@SkyManagement]

If it started again immediately, then it could be that the seals were the wrong size. The carriage can also leak out of the top and it will look like the same issue. But replacing the o-rings won’t fix it. Here is a link to a video on how to change the Carthage. kzbin.info/www/bejne/eWibc4SfoJtgl8k I hope this was helpful.

[@ilfisarmonicistapazz]

Very difficult for me to find the right o-rings (they have a special form). Should we use also tap grease on the rings?

[@SkyManagement]

Yes. It is a good idea to grease the fitting when putting it back together. I would think most any hardware store would carry most sizes. If you have a very unique faucet, you may need to go to a plumbing supply store. Unfortunately, they can be a little harder to find.