KLE500 | Carbs adjust and sync

[@CD-pi8xq]

No talk, no music, just facts. Refreshing. Cheers.

[@markariewilliams]

Thank you for this, only thing i would add is if possible while everything is apart, do a valve clearance check first then balance the carbs for best effect.

[@Maistrou88]

Hello, helped twice already! Respect!

[@МаксимФищенко-к7т]

Я вообще синхронизацию делаю при снятом карбюраторе, смотрю по через свет заслонки и регулирую зазоры, все просто

[@tgap8817]

es efectivo??

[@jackpoell1673]

Good video, but did you really use a kind of locktite to settle the pilot screws? And synching the carbs is usually done with an engine that’s warm enough, so did I miss something!

[@DenonGregory]

Wish there was some vocal explanation and steps. For a person just learning or never doing this won't quite know what you're doing. But besides that it was detailed in other areas.

[@Maistrou88]

Bro, at any motorcycle service you'll hear more... Do it!

[@Конструктор-Евген]

Отлично друг. Ничего лишнего и понятно. Спасибо

[@IZHASAKI]

Самое лучшее видео! 👍Без лишней болтовни🤐👍🤝 Rakhmet!

[@TheThalassa50]

Nice patent with the tubes for the adjustment, what diameter are they in mm please

[@CrespoTorke8]

Muy buenas, muchas gracias por el video, solo me queda la duda del diametro del tubo, ¿Es de 0,8 o 0,6? te agradezco mucho que te tomases el tiempo de grabarlo y compartirlo.

[@stuartbrown1426]

What did u adjust then to sync them u didn't show it would of been helpful.

[@captain680]

Молодец! Полезное видео! Благодарю!

[@nikitniki680]

Thanks a lot for this 🏍️

[@chariskopsacheilis7684]

Hey man, nice job contributing to the KLE community :) These videos help a lot. Can you tell me what was that thing you put on the pilot screw before you put it back on? Keep them coming!

[@CronoCueva]

Hi, its only a soft glue (screw fixer i think), you don't really needed but it will stay a bit longer in his position

[@haraldfauske1599]

Thank you!!

[@pawelo821]

Super, dzięki za filmik

[@constantinistrate72]

Hello! What liquid is there, gasoline colored with something?

[@barpex_]

This Video has a problem... wich screws did he turned?

[@JensEskildsen]

Look from 4:40, or in the manual regarding synchronisation :)

[@badmadmat20]

Hey, great video. However, how long did it take you to unmount the carb? Was it difficult? Do you have any advise ? Thank you :)

[@miloshadzic8099]

Can you tell me the diameter of the plastic hose that u are using? I guess it has to be a good tight seal on the carb

[@antoniogarciabaquero3765]

He puesto aceite de moto 2 tiempos y nada, se lo bebe. Desisto. Ya no se que hacer. De todas maneras, muchas gracias por tú interés.

[@sefatop8784]

there is still deviation in the sync setting left down right up

[@ManuelRamirez-sz7hk]

Alguien sabe que balancines son compatibles con la 454 modelo 86

[@UgurYenigun]

wonderful

[@LMCtubokuChannel]

Nice work 👍

[@GuntarsAm]

Does any body knows problem when my kawasaki kle 500 warms up it lose power on full throttle? On minimal throttle it goes well..

[@BenimYolumMyWay]

Hi, thanks for the nice video. My motorcycle does not work in the first run without giving gas while it is cold. When I run it, it stops if I do not gas. There is no problem with the engine warming up. What can I do?

[@CronoCueva]

Hi, I don't know, but maybe you have too much gas in the mix, not enough air (that's why you need to give gas). I recomend you to chek every single screw from the carburator, air filter maybe? but i really don't know...

[@leobardogarcia8307]

CronoCueva Hola me gustaría contactar te para asesoramiento yate deje mi correo hoja la algún día lo leas saludos

[@BenimYolumMyWay]

Thank you There is no problem. He's interested in valve settings. The setting was fine.

[@N.D.678]

I have the same problem with my KLE. He just refuse to keep working when he's cold. I need to pull the choke or as you said to I have to turn throttle a little bit down for 1 minute while he's warming up. But recently I noticed that eventhoug I keep throttle dow for 1 minute he stops working after that. pleas e reply this if you find the solution of this problem . greetings

[@TheKilab]

In my case I have this problem after riding for a while. The problem usually goes away after I clean the carbs

[@antoniogarciabaquero3765]

Muchas gracias, puede servir aceite motor del coche 10w40?

[@CronoCueva]

Si, prueba con el de motor de coche, el de moto creo que es demasiado liquido ya que está hecho para mezclarse con la gasolina, si con el de coche no funciona el que el tubo que utilizas es demasiado grueso. Pero en principio con el que comentas te deberia funcionar.

[@riskromer9773]

I guess I understand but it would be nice if you could say what the parts are called and what you are actually doing. If you don't want to speak at least some captions would do. Thanks

[@XxJockerSergioxX]

Que líquido es?

[@623dnb]

What's in the hose? Red?

[@KLAYDIOS1]

the liquid you have in the tire the red what is

[@Smodlee]

Who taught u that trick with the wood and tubes? I thought I was the only one in the world that invented that?

[@CronoCueva]

i read it on internet, looking for a cheaper solution than buying a vacuum gauge...

[@josequintero2193]

Mis carburadores tienen sellada esa parte

[@DanielContreras-ho6ql]

Es un tapón que se puede quitar amigo saludos

[@623dnb]

how much rpm?

[@saroshqureshi4814]

when adjusting, do u screw on the pilot, or the throtle screw ?

[@CronoCueva]

the pilot 1:04

[@davidmolnar3803]

Throtle

[@erciyesceteci9242]

I couldnt understand how did you adjust the vacuum, is there a screw for it.

[@brendymorales-qc8uq]

Si hay un tornillo enmedio de los dos carburadores que se jira para sincronizar los carburadores

[@antoniogarciabaquero3765]

Buenas tardes. Alguien puede echarme una mano. Yo conecto los manguitos a ambos carburadores y en cuanto la pongo en marcha, se bebe la gasolina. Algo estoy haciendo mal.

[@CronoCueva]

Hola, dentro del tubo tienes que poner aceite, no gasolina, y luego comprueba que el tubo no sea muy grande o el aceit muy liquido para ver que funcione bien, lo normal es que sea lento moviéndose. Suerte!

[@MarioDiaz-co3px]

Eres de Catalunya?

[@N.D.678]

what is the substance in tube on 1:18?

[@CronoCueva]

Screw fixer! :)

[@egorkin1982]

@@CronoCueva I would say threadlocking adhesives.

[@АлександрПурин-ъ1о]

Ага, было бы это все так просто.... Геморрой

[@Maistrou88]

Не хочешь срать-не мучай жопу, а потом геморрой.

[@tonielezi8458]

I learned nothing, thnx

[@Maistrou88]

Read the book then

[@clarkjoel]

Annoying video sounds... if no talking about what's happening, put music so we dont hear all that squeaking & breathing

[@Maistrou88]

Skip it & go for moto service then