Klipper - Mainsail - Fluidd - 2022 - Chris's Basement

[@bobwtech]

Got Klipper and Fluidd on my thin client then I was clueless on what to do. This video filled in the blanks and I'm up and running. Your instructions are the best!!!!

[@ChrisRiley]

That is awesome! Thanks so much for the support! Always great to hear my videos helped someone!

[@pneumantic6297]

For the people that might get confused since he left it out, when he puts in make the first time after he puts in make menuconfig

[@ChrisRiley]

Thanks!

[@SchwettyBawls]

Decided to finally try clipper and immediately searched your videos. Yet another awesome video that helped me immensely. Thank you for being awesome for all these years.

[@ChrisRiley]

Glad I could help! Thanks

[@ogmaker]

Given the dirth of Raspberry Pi stock, Kiauh is a really amazing tool that will install Klipper and your choice of UI, moonraker, etc. to almost any system running Linux. This allows use of the alternatives to Pi easily without having to do manual installations.

[@ChrisRiley]

Thanks Bill, I haven't checked Kiauh out yet, I will now though. I think that is worth a video.

[@bobwtech]

I just used Kiauh to install everything on a thin client today. Now, thanks to Chris, I can finish getting the Klipper on my printer. I chose Fluidd by flipping a coin ;).

[@gaxon1920]

Orange Pi works as well and stock is still available at normal prices.

[@darthkarnagge8343]

Without this guide I would have never even tried to install Klipper. Thank you!

[@ChrisRiley]

Glad I could help!

[@ScottLahteine]

That was a really great summary of the lengthy Klipper setup procedure. I actually found it cathartic!

[@ChrisRiley]

I'm glad I could help!

Duude! Most complete and straightforward video! Awesome! Congrats man!

[@ChrisRiley]

Thank you!

[@doyouflytoo]

I'm running mainsail on 4 printers fluid on 1. I still wanted to watch Chris's video because I knew I would still learn something.

[@ChrisRiley]

Thank you!

[@justindelpero]

Same. Full Klipper user but I like Chris's delivery on these topics and it's arrogant to assume I know it all haha

[@jannejcperme3238]

Chris thanks for this video. Most of guys on KZbin have the old method, where u download your klipper and flash via Etcher. This is far more simple. Hi from Slovenia !!!

[@ChrisRiley]

Hello! Thanks for watching!

[@christophe_decenon]

Hello, fantastic video, I have gone through a lot of documentation on Klipper through the internet. Chris, your video is an absolute reference, thank you for this work ;-)

[@ChrisRiley]

Glad it was helpful!

[@FeistyAcorn]

Great tutorial! I wish I would have found this video before my dive into Klipper. It would have saved me a lot of time!

[@ChrisRiley]

Glad it helped!

[@NoNameAvailable23]

Mainsail and klioper have been game changers. Great vid, learning lots!

[@ChrisRiley]

That's great, thanks!

[@3dstampa]

I am soon going to start with klipper experimenting (long time marlin user here) so these type of videos came in a right time for me. Great stuff!

[@ChrisRiley]

Glad it was helpful!

[@53Ericd]

Thanks Chris! I have tried to load Kipper in the past and failed. Your set of new videos will get me there. Looking forward to seeing the others!

[@ChrisRiley]

I'm happy to help. Thanks for watching

[@Casuallylost]

you sir are a legend! been trying for days to get klipper to work...

[@ChrisRiley]

Thank you!

[@DJ-Hollandica]

its great you ppl make these video's ill gonna steal this one and put it on my cloud ...pretty hard for a noob this helps allot...you use the pi to compile any board ..iam on it thanks

[@ChrisRiley]

🙂👍

[@zora_tech]

Awesome thanks for the video. You always make very in-depth videos that are easy to follow I can't wait to see the other ones you will be making

[@ChrisRiley]

Glad you like them!

[@JohnOCFII]

Excellent overview of Mainsail and Fluidd. I’ve tried them both, but settled on Mainsail. Looking forward to the rest of the series

[@ChrisRiley]

A fine choice! Thanks for watching

[@justindelpero]

Nice work. One thing I think you should cover is the ability to flash klipper over serial. I do it periodically and it's nice because my electronics are a pita to get to. Serial flashing allows you to skip the SD card dance.

[@ChrisRiley]

Thanks for the info!

[@Plan-C]

As usual, thank you for breaking it down.

[@ChrisRiley]

I'm happy to help!

[@f1hotrod527]

This is all over my head. I guess I just need to try to do it step by step

[@ChrisRiley]

There is a lot of info here, but it follow the docs, so it helps to have those up at the same time. This way it's easier to copy and paste commands.

[@mitsre]

Just for a coffee! Many thanks for your videos!!!

[@ChrisRiley]

Thanks!

[@corlissmedia2.0]

I posted some comments on my efforts to get my Lerdge K board working on your video about doing the same.

[@ChrisRiley]

I'm working through all these to get to your most current post.

[@brewerbrewer0623]

Thanks for the knowledge! First-time tinkerer who just got Octopi running Klipper but you've encouraged me to expand my horizons! Leaning towards Mainsail but you presented Fluidd really well too! Great job breaking everything down into salient points with clear explanations. Have a like and a sub!

[@ChrisRiley]

Glad I could help!

[@PMcDFPV]

YASSS ! My ender 3 is coming along, in my test prints an issue followed me from marlin, my cube is still not as close to 20x20x20 as I need, so its deff mech, I ordered some new gates belts \ pullys and idlers for X and Y and hoping that helps :) BUT if it does not, would you consider doin a video on what to do to get closer to that fine tune, or did i miss one along the way ?? lol :) thanks good sir !

[@woodwaker1]

You might want to watch the video by Vector 3D, He has developed a system to calibrate your printer. It is about $5 to purchase, but I have used it on 3 of my printers with success. Take a look kzbin.info/www/bejne/h4vXf3doeZaIZ6M&ab_channel=Vector3D

[@ChrisRiley]

Hey Paul, glad it's coming along. I have never done a whole video like that, but I will think on it. There might be a way I can show how different changes effect accuracy.

[@-_Robert_-]

Thank you Chris. You'd help me a ton.

[@ChrisRiley]

Glad to hear it! Thank you

[@timzimmerman7893]

Chris, Can you do a video on the Kraken and it's setup with both Klipper and with Marlin?

[@ChrisRiley]

I don't have a Kraken yet, but I will see what I can do.

[@SheLeftMeUnsupervised]

Love the way you go step by step on your video's. Going to try Klipper on my x5sa. The printer is a real POS with stock firmware. Have had this thing a year and haven't even been able to get it to level or home. I hope klipper will be my rescue for this machine. Just can't make up my mind which ui I want to try. Long time user of octoprint but I am open to fluidd and mainsail. Maybe I will just install all 3 lol. See what happens. Have octoklipper installed on my sd card now. Should have more sd cards in the mailbox tomorrow for trying out the other 2. If Klipper runs well on the x5sa I will probably try it on my flsunqqs pro and ender 3 pro. (Kinda want to build a voron and ratrig too..)

[@ChrisRiley]

Awesome, glad you like the video, I really like mainsail, not sure why, but it seems easier to use.

[@SheLeftMeUnsupervised]

@@ChrisRiley I ended up installing KIAUH klipper on my pi for testing. I attempted to flash my mainboard and found out it has a strange firmware. When I went to flash it nothing happened. Apparently I have to use different software to flash to an older firmware to then flash to klipper. This is getting interesting lol. I am almost to the point of just replacing the board and putting on a bltouch. With the KIAUH I can experiment with all three of the UI's so looking forward to getting this thing working. The main reason I want to keep octoprint is Home Assistant. Nice thing is I can still use them all so I call it a win. So If you have an X5SA and going to flash klipper its going to be an interesting process!

[@musicdad]

I have my folgertech ft-6 running klipper. It's great

[@ChrisRiley]

Awesome! Good luck with your projects

[@aaronk3678]

Hi Chris. I used Fluidd as my goto for a long time. I now install both of them with every setup. I find Mainsail is becoming more my thing for the moment. They are both solid and similar features. Thank you for the great videos!

[@ChrisRiley]

They both have their attributes. Thanks for watching.

[@retroluminico]

I have a request Chris. A print quality compare betwen an ender 3 with klipper and with RepRap of the mellow fly. Despite of the cool of the firmware the main purpose of a 3d printer is to produce 3d printed objects. Maybe klipper can really produce better prints on the same hardware. PS. Your videos are truly a main guide for me thanks for your time

[@ChrisRiley]

Thank you! Yes, we are going to take a look at print quality as soon as we get the basics done.

[@onleditpas]

keep up the good work Chris, I have started migrating my x5sa to klipper so I’m definitely interested in getting more. So far I have both mainsail and fluidd running on the same computer but have mostly used mainsail.

[@ChrisRiley]

Thanks, more to come!

[@woodwaker1]

Chris, good series on Klipper. I know you are not a fan boy the way I am, but you have presented a very fair explanation of the process. I loved Octoprint and Marlin, until I discovered Klipper. The big difference is the ease of editing the configuration files, once you do get it set up - you will never have to compile again. You might delve into how Klipper moves the work onto the Pi from the printer mainboard and other things it can do like pressure advance and input shaper. Rat Rig has an image that is really different - RatOS that is complete with optional configuration files for each version of their printer.

[@ChrisRiley]

Thanks Dave, I'll look into it!

[@QTheMost]

Thank you. I blew my x5sa board.. So i just installed klipper and mainsail. Now i just need a better cfg file

[@ChrisRiley]

Awesome, glad it helped out!

[@mitsre]

Thank you for the great videos which you do. I have a custom ender-3 with a SKR E3 Turbo board and dual lead screw with dual stepper motors. Still today I use Marlin by z stepper auto align (G34). I'm thinking of trying Klipper but I don't know what choices there are in this case. So I believe that will be a great idea and helpful, if you can make a video like the "All things z - deep dive" but this time for Klipper!! Many thanks in any case!

[@ChrisRiley]

I'll look into it, thanks!

[@noahmiller794]

Can't wait to see the Klipper on the Andriod video

[@ChrisRiley]

I'll see what I can do.

[@nejcklenovsek5372]

If you did not exist i could never run klipper on my printers, thank you again :D

[@ChrisRiley]

Glad I could help!

[@JeanPierreLereboullet]

Thank Chris for this great video. I’m still using Octoklipper, and I’m wondering why Mainsail is so loved, and if this could be linked to the way to update Klipper version?

[@ChrisRiley]

I think Mainsail is just a little more dedicated solution for Klipper. The updating alone probably makes it worth a try.

[@gottria]

Just watched your video on Octoklipper, now this one all done fantastic, thanks. But between the 2 which do you prefer?

[@ChrisRiley]

Thanks! I really like Mainsail, it just seems easier to use.

[@Brainwork66]

Thank you for this video, it is really informative. I want to ask, if im running octoklipper now and want to try mainsail i have to make an new config file and upload to my printer or i just need to install mainsail to my raspberry and connect ?

[@ChrisRiley]

Thanks for watching! Just mainsail on Raspberry Pi. I would look at the Kiauh install it will let you install it as well very easy. www.lpomykal.cz/kiauh-installation-guide/

[@cranborile]

Thank you everything explained so well & clearly 👍

[@ChrisRiley]

You’re welcome 😊 Thanks for watching

[@ColdBloodedCreaturae]

This tutorial has been awesome. But any idea how I can figure out the right GPIO pin for my Anycubic Vyper?

[@ChrisRiley]

Awesome, about the only was is through and example config github.com/Klipper3d/klipper/tree/master/config or hope someone has done it and you can google it.

[@EsotericArctos]

Have you ever used KlipperScreen on a touchscreen at the printer? Is it similar to Octodash for Octoprint?

[@ChrisRiley]

I have and yes it is, check this one out. kzbin.info/www/bejne/m6Wsm3-PbLOIj7s

[@jdclegg74jc]

Changed to BTT E3V3 after my Creality 4.2.7 became faulty. All back up and working with ease after following this video. 👌 One question though, my ender 3 pro screen was showing some basic info (temps, fan speed, progress%) but now its just blank? Can I get that info back or is the screen now redundant?

[@ChrisRiley]

Awesome! With Klipper, they don't support very many screens, so most of them cannot be used I'm afraid. They intend for you to use the web UI.

[@mickredfox]

hi Chris, great video, Where can i find the gio pins to set at micro-controller startup for the skr1.3 board? I don't find it. thanks for your answer

[@ChrisRiley]

Here it is, looks like you don't need to change anything with GPIO for this one. github.com/Klipper3d/klipper/blob/master/config/generic-bigtreetech-skr-v1.3.cfg

[@mickredfox]

@@ChrisRiley thanks Chris, I look at it

[@paulnolastname9422]

Well, I think I'm going to give this a try. I recently was able to free up my Pi4, so nothing is holding me back. I'm still running an old version of Marlin, so I guess I'll take the plunge. I have an old TAZ5 that could probably use some updating.

[@ChrisRiley]

Good luck with your projects!

[@matuskunik2068]

I need to switch the states of endstops, because my shows triggered when they are not, and open when they are triggered. In marlin it was an easy step to switch the detection, but cannot find nothing in Klipper/Mainsail. Thanks for help.

[@ChrisRiley]

Put a ! in front of the pin number to flip it

[@orionmec]

Chris, your videos are very good. You put is out there so that it seems pretty easy... But damn. It is a lot to take in. I just tried the Creality Sonic Pad and it will not work. I have a CR-10S Pro and had to put a BLTouch on it, when done the Sonic Pad still errors. Im thinking that I may just go the Pi method... But you can't get one reasonably so I'm looking at the Bigtreetech CB1..... Do you have any info on that one for install Klipper install?

[@ChrisRiley]

Thanks! I don't know much about the CB1, but be careful, some of the board you see still require a Pi. Not all the vendor models seem to do the job well. I am still looking into a few of them.

[@ouzts12]

I'm building a custom IDEX printer and now just need to configure and flash firmware. Which UI might be better for IDEX--Mainsail or Fluidd? Or does it not matter? Thanks

[@markwreich]

Awesome video! Thank you!!

[@ChrisRiley]

Thank you

[@yaVDRgda]

Before doing a "make menuconfig" I would do a "git pull", because the Klipper files could be rather old. The sudo command doesn't ask you for the root password. It asks for the pi password. Normally you would delete the root password for security reasons, so a login for root would be impossible. sudo would still work, because it is not the root password that is needed.

[@ChrisRiley]

Thanks for your insight!

[@yaVDRgda]

@@ChrisRiley You are welcome. I would have done the installation of Mainsail and Fluidd differently, more easy, but I don't want to tell about it in the public.

[@justindelpero]

@@yaVDRgda kiauh?

[@prongATO]

What brand of drums do you play/love? I finally got a nice natural maple Gretsch 5pc single.

[@ChrisRiley]

I played Sonor for years and really liked them. I switched to DW about 10 years ago, they have been really great, awesome sound, very well made.

[@Dan_Murphy]

Any idea why my cr-10s pro wouldn’t connect to mainsail until I installed the rc script and switched the microcontroller to Linux process? It’s not listed in the documentation as a requirement unless you’re setting up an adxl.. but nothing I did would get my printer to connect until I did that.

[@ChrisRiley]

Wow, I don't know, maybe the config you had didn't need a certain config item and the re-flash somehow cleared it. I'm not really sure.

[@TheBobekProduction]

Good day I'm building Voron2.4. After G28, the Hotend homing, but the Z motors don't lock, you can move them up and down with your hands even if they light up blue. I can't get further because it fails on QGL. The board is Spider 2.2. Can you advise me? well thank you

[@ChrisRiley]

You have something turning the motors off somewhere. Does anything pop up in the console after you G28?

[@TheBobekProduction]

@@ChrisRiley t was a mechanical problem, it's solved, thank you

[@3dstampa]

Thank you again for this video! I am runnig klipper+mainsail on my E3Pro (with skr e3v3) from CB1 and Pi4b adapter. Is it possible to use one instance of Mainsail and translate it to second E3Pro or would I need to buy another CB1?

[@ChrisRiley]

You can do it, but I'm not exactly sure how it works. There are a few folks on the internet that have worked it out.

[@3dstampa]

@@ChrisRiley Thanks Chris. I'll take a look :)

[@maximecarrein]

Hi, trying to install klipper on my SKR E3 V3 as well. However I can't seem to find what to do with the "GPIO pins to set at micro-controller startup". In this video 30:03 . What GPIO pin did you use. Any idea? Or where did you find the info? Thanks in advance!

[@sz7795]

Hay chris I can't find what gpio pin should I set for mks robin nano 1.3 can you please point me in a direction where I would be able to find it

[@ChrisRiley]

See if this helps. github.com/Klipper3d/klipper/blob/master/config/generic-mks-robin-nano-v3.cfg

[@The1Perfume]

Chris what’s the gpio pins for a stm32f401 ? I can’t find anything

[@ChrisRiley]

Which board is that, I can't find that chip.

[@mohyki123]

you are the best my man

[@ChrisRiley]

Thank you!

[@whatif8741]

If i have already flashed klipper to my mainboard i don't have to follow the steps at 9:35?

[@ChrisRiley]

Correct, that part is just to flash it to the board.

[@nicholascarssow4800]

How do you find the GPIO pin #s ? I have a Mini SKR E3 V3. Help?

[@ChrisRiley]

The best place is in the klipper examples. Not all boards need this setting. github.com/Klipper3d/klipper/tree/master/config

[@NetDoc2k]

That was awesome. Thanks.

[@ChrisRiley]

Glad you enjoyed it!

[@BrianVoelker]

Thank you so much for this!!!

[@ChrisRiley]

You're so welcome!

[@Nitram_3d]

how to flash the mainboard is stated is the printer.cfg file for respective board in the documentation... if you have a common board.

[@ChrisRiley]

Cool, thanks!

[@highspeedpiTV]

Mainsail all day!!

[@ChrisRiley]

👍🙂

[@carlhaw2601]

is there a way two run 2 printers on a single pi using mainsail.?

[@ChrisRiley]

Yes, the easiest way is with Kiauh, check this out. kzbin.info/www/bejne/gnrQmnmjnbJ0eJIsi=xgjkWfxiRmbjTfWZ

[@Geek82]

yah i cant get the fluidd local to work. I can ssh into the pi and everything but i cant log into the fluidd web interface. im about to just try it with octoklipper. im not sure what the deal with fluidd is but the network issues are odd.

[@ChrisRiley]

I have problems with .local addresses sometimes. It could be some issue in the Fluidd host file. Ask a question over on their github, it might be a known issue.

[@Geek82]

@@ChrisRiley currently planning on flashing it all from start. And seeing if that helps. Probably a config file

[@Geek82]

@@ChrisRiley also tried via the Mac and the IP. Connection refused. It's a known issue but the workaround is even crazier.

[@LejeuneBryant]

IS there any way you could help me out directly. I've been trying for 4 years to fix my Ender 3 Pro , and I need some help . I 've watched many videos on how to install klipper on my printer. I have WinSCP, a Raspberry Pi 3 MIcro sd card. I live in ORegon so I'm on Pacific Time zone.

[@ChrisRiley]

Hey, I can try and help, send me an email [e-mail]

[@thegmkiller1967]

If I have a preflashed pi and board from fysetc that has klipper installed with octoprint. Can I use KIAUH to change to fluidd from the octoprint

[@ChrisRiley]

Not sure yet, stay tuned

[@jakefromstatefarm8545]

Hey Chris. Is there any way to install Mainsail, Fluid, and Octoprint on the same pi? I keep reading that there is, but I don’t see how it’s possible when the imager just overwrites the SD card. Is there another way to go about that?

[@ChrisRiley]

I would think you could, but you would have to have them with separate installs. Or there would be some serious hacking as far as ports and things. I will think on it, not sure how all that would work.

[@csdstudio78]

Kiauh.

[@dannyperkins4220]

help from anyone I am using a MacBook Pro, what can I use instead of putty for setting up Klipper. any help will be appreciated .

[@ChrisRiley]

I've don't use Mac, but I have seen tools like this. termius.com/free-ssh-client-for-mac-os

[@wavywave2597]

i have a ender 3 with a stock 4.2.2 board but i have a 4.2.7 silent board coming in the mail and i was wondering what gpio pins i would need to type in for it also would they be the same. Thank you!

[@ChrisRiley]

Check you the example configs, they have all the pins in them. There is one for both boards. github.com/Klipper3d/klipper/tree/master/config

[@wavywave2597]

@@ChrisRiley hi I was able to figure it out but now I’m stuck again with a .hex file which I have no idea what to do with

[@S00rabh]

@11:54, you did not explain what these GPIO pins are. I cannot just google search it. No information is available. Example: BTT SKR2

[@ChrisRiley]

Check this out, it might help. kzbin.info/www/bejne/p4SUhXZtr7uLj9k

[@S00rabh]

@@ChrisRiley thanks man. Really appreciated. I know why I subscribed.

[@ThePrintZone123]

time to do a 5 minute benchy on ender 3 pro using fluidd(i mean 3dprinterfun could. it definently won't take me 5 years right?------- Right?)

[@ChrisRiley]

I have faith in you!

[@ThePrintZone123]

@@ChrisRiley XD

[@107Anderson]

i am getting the "mcu 'mcu' : Unable to connect" error how do i fix it?

[@ChrisRiley]

It's almost always the GPIO pin causing you problem. Check your setting in menuconfig again.

[@alexanderthompson9895]

Speaking of, any plans on doing a 2.4 build w/ Klipper?

[@ChrisRiley]

Coming soon!

[@NetDoc2k]

I have a screen installed on my pi. How do I get into the shell/GUI?

[@-AT-WALKER]

Hey random question for you as it looks like you've done the steps recently - Did you use the FluiddPi or KIAUH script? The site recommends NOT using FluiddPi and recommends KIAUH whilst GIT states "Usage of this script happens at your own risk!" Cheers in advance if you answer!

[@ChrisRiley]

I just built it from command line, but I do recommend KIAUH for these installs, it works much better.

[@ChrisRiley]

If it's an HDMI screen, it should just come up, otherwise you will have to install some drivers via command line. The people you got the screen from should have the commands you need to run.

[@СергейШиряев-п8щ]

Установил Klipper - Mainsail на Ender 3Pro всё хорошо! Большое спасибо. Но через несколько дней при включении появилась ошибка... Открыл файл Printer.cfg а он пуст. Скопировал в него повторно всю информацию - заработало. На следующий день опять тоже самое. Файл Printer.cfg оказался пустым. Что может быть за причина? Куда девается информация файла.

[@ChrisRiley]

Единственное, о чем я могу думать, это то, что в файловой системе есть какое-то разрешение на запись, которое препятствует правильному сохранению файла. Может быть, вы можете перейти на другую версию, чтобы избавиться от этой ошибки.

[@zergmare7]

So why choose Fluidd or Mainsail over say, Octoprint?

[@ChrisRiley]

As far as Klipper is concerned Fluidd or Mainsail have more integrated features then using the octoprint plugin. They are just a lot easier to use.

[@zergmare7]

@@ChrisRiley Great, thanks!

[@Frankie_Freedom]

Anybody encounter issues where it doesn't update using the button, can't get the system to update using mainsail

[@ChrisRiley]

Only problem I have had is the order I updated them in. Some times I have to do them separately until they all succeed.

[@BukkitViper]

Thank you that helped a lot

[@ChrisRiley]

Glad to hear it!

[@chrisl7008]

what if im using a th3d ezboard? im in the klipper config currently

[@ChrisRiley]

There is an example for it. github.com/Klipper3d/klipper/tree/master/config

[@chrisl7008]

@@ChrisRiley thank you so much

[@elgunshirley3375]

for me i serial does not show up i did everything thing in step and this is what stopped me if you can help me that would be awesome

[@ChrisRiley]

Some times the boards get confused and won't show up. Set your MCU as the USB device listed in /dev and see if it will work. You can find that with ls /dev/tty* It's going to be something like ttyAMA0

[@elgunshirley3375]

@@ChrisRiley hello again I tried what you said and my id came out as this usb-1a86_USB_Serial-if00-port0 is this the correct id?

[@ChrisRiley]

@@elgunshirley3375 That looks like it should be correct. It might be connecting, but there is an error in the printer.cfg. Make sure it's not calling out something in the GUI.

[@elgunshirley3375]

@@ChrisRiley ok thank you so much

[@marcelpsilva]

Nice video!

[@ChrisRiley]

Thanks!

[@fastfood122]

Hi Chris i did the same but klipper reporting startup saying printer is not ready clipper software is trying to connect ,the its saying mcu rpi unable to conect why what wrong ? Thank u bro.

[@ChrisRiley]

Hey, it's usually an MCU pin issue. Check the example config for your board and make sure you are using the correct pin when you compile.

[@fastfood122]

It worked !!!!

[@fastfood122]

U r an angel Chris

[@fastfood122]

I was doing mainsail 46 bit as my pi is 46 bit and it didn't work, i tried the 32 bit it worked😂 I'm so happy brother hands down for you 😇🙏thank u 🙏🏻

[@fastfood122]

I'm using the mellow fly super 8 1.3v not sure if it need a pin and i couldn't find the pin for that board as I'm a beginner lol but it worked lol 😂 can't thank u enough🙏

[@wrxsubaru02]

I just setup Klipper for the first time which took me about 2 days to get the config and everything working, but now I am stuck where I cant print anything. Every time I try to print from OrcaSlicer to MainSail, it fails and says: // Unknown command:"SDCARD_PRINT_FILE" Its driving me nuts trying to figure it out!

[@wrxsubaru02]

Thanks for helping me telepathically again, Chris! LOL I added this to my printer config file: [virtual_sdcard] path: ~/printer_data/gcodes on_error_gcode: CANCEL_PRINT

[@ChrisRiley]

LOL! You're welcome!

[@thediscoman2001]

mine will not connect to host at all

[@ChrisRiley]

The quickest way to get up and running would be to let Kiauh do the work. kzbin.info/www/bejne/gnrQmnmjnbJ0eJI

[@beauslim]

People should watch out for speed settings in any printer.cfg file they grab from somewhere. My bearings started screaming and needed a good clean and lube before I could run my printer at typical Klipper speeds.

[@ChrisRiley]

Thanks for the tip!

[@axelmg89]

Hey man it was great meeting you at ERRF last week. Like I told you, your videos helped me out of a lot of jams. Now of course you come up when I’m looking for info about Klipper. So thanks again! Quick tip: Give Mobaxterm a try. It basically combines putty and winscp into one tool. It’s pretty sweet. And I believe it’s free/you don’t need a license for it if you’re just one user.

[@ChrisRiley]

Great to meet you too! I'll check it out, thanks

[@MarcusSilvamvs]

Great!!

[@ChrisRiley]

Thank you

[@The22v10]

Great Video, fluidd .LOLL

[@ChrisRiley]

Thanks 👍

[@thelazy3d431]

the kiauh script automates the install with a command line gui

[@ChrisRiley]

Thank you

[@thelazy3d431]

@@ChrisRiley your welcome

[@Thomllama]

I'd try Klipper, but you would not be my friend anymore after a month of annoying questions ever 10 mins!!! LOLOLOL

[@ChrisRiley]

Lol! You'll always be my friend!

[@bengtejo]

"A lot of WORK" does not apply for a hobby!😁

[@ChrisRiley]

How true. 😀

[@jakefromstatefarm8545]

#TeamMainsail

[@Mainsail-Crew]

Mainsail-Crew :P

[@ChrisRiley]

🙂👍

[@elfpimp1]

Now if I could only remember where I put my two Pi's.. 😐

[@ChrisRiley]

Better not lose those, that's a hot commodity!

[@elfpimp1]

@@ChrisRiley well, good news, I found them. But not sure they're hot commodities, Lol, these are a few years old and i only paid $14 for the two at the Goodwill near me.. 😁👍

[@PunaJussi]

11:05 should be "make menuconfig", too fast edit

[@ChrisRiley]

thanks

[@gg-gn3re]

man mjpeg still.. when will the 1990s end. webRTC with literally anything (h264, typically) has less latency and 1/10th the bandwidth =[

[@ChrisRiley]

lol, yeah, not sure why, but this is what we're still doing.

[@colincampbell3679]

Holy Heck.. He said at the start that this is for those of us who know nothing or little to know nothing of Klipper.. then zooms fast through tons of typing and talks fast about this that whatever! So how the heck are we whom as he said know nothing about how Klipper is set up, to keep up with this very fast talking oh type this that stuff again fast and with commands we have no knowledge off, how can we newbies of Klipper even hope to keep up? This is a very complex thing to learn and try to get our minds used to and your zooming along like we already know how it is done? There is so little around to help us newbies to all this as it is. We need slow step by step clear shown close up screen shots that point out what and why we need to do what is needed? Not zoom through with no close up typed commands shown. Remember we new to this don't know anything about the many commands of where to get the files or how the system is set up!

[@ChrisRiley]

Thanks for watching. I'm sorry to hear that you're having trouble. I know the videos move quickly. It's a fine line between moving slow enough to teach, but fast enough to keep our audience interested. Maybe this video could help: Klipper Firmware - Install kzbin.info/www/bejne/p4SUhXZtr7uLj9k Also, you can adjust the playback speed by hitting the COG ( ⚙ ) icon on bottom right hand side of the video. Please reach out if I can be of assistance.

[@coffinsnail6930]

your video is wrong first load of the rasberry image with moonsail wants moonraker first and only

[@ChrisRiley]

thanks

[@p.nation3583]

hello im currently installing klipper on pie 4. did all the step by step instructions... how come i cant get the mainsail.local to open ? i followed all the steps did i miss something?

[@p.nation3583]

Nvm had to connect to dif port for power n had to wait to be installed

[@ChrisRiley]

Glad you found the issue.