Many Do Not Know How To Weld Aluminum, Cheap and Fast

[@GuestInvitado-gd3bi]

These repairs have been around since oxyacetylene was integrated into the auto repair shop. It' s called gas welding. I do it all the time. Two thumbs up. 👍👍

[@cornwallav8r]

Yes but do you know the steel welding rod trick? I didn't till now, never got really good at tig or gas welding aluminum, he made it look like soldering, which I'm a pro at. Will make all the difference for me personally.

[@cangurojr.3112]

Disculpa mi ignorancia pero se puede usar un soplete de bote para soldar asi o necesitas los dos tanques

[@W.J.Blythe]

I hope you use a flux 😬

[@maxwebster7572]

@@cangurojr.3112 Depends on the melting point of the alloy and what gas you use.

[@fragolada]

@@cangurojr.3112 El soplete de lata no alcanza las temperaturas del oxiacetileno. Recuerda que el oxiacetileno está diseñado para cortar el acero

[@travismailsa1]

From what i was taught when i was a kid, this was called brazing to me when i was to repair/fill or join weak metals?

[@worthmor5146]

Couldn't tell what the rod he was using. But yes, if you use a brass rod it is brazing.

[@johnbelwell2461]

For a flywheel dust cap fix, this weld is very VERY good! A little grinding and it'll be like new. Whoever says the opposite must be one of those guys from the bad clan of welders who are always alarmists, criticize beginners and think that if you weld a piece of crap you have around you're useless if it doesn't have the integrity of a nuclear reactor.

[@andyroo3022]

Agree. After dressing up and polishing the repair will be fine.

[@DualsPortvet]

Or, they may know the difference between welding and melting. Heating up the aluminum and the smearing the top layer to close cover the crack isn't welding. A weld should be stronger than the material around it. This may work for this application, but per the title of the video, it's not welding more "like" brazing.

[@IsaacOLEG]

@@DualsPortvet absolutely. Now, may I use an aluminimum MMA electrode (without the coating ?) to do such a "gluing" I need to repair a hinge for a bycicle, essentielly the ring is holding the axis in place I suppose a lesser resistance is acceptablme. I heve the aluminium rods, but I am afraid to melt the ring vey easily .. Now, is it possible to solder copper or bronze commer on the aluminium of that bycicle frame ? THANKS (a lot)

[@glennlane1056]

It won't survive a little grinding

[@maxwebster7572]

That's a zinc rod. Aluminum likes flux.

[@cornwallav8r]

That was amazing. Not so much the gas welding but the use of the steel rod to give feedback to when the aluminum goes liquid, it's perfect. Makes all the difference, thanks.

[@kidkv]

It would be a Stainless Steel rod, not a steel rod, that he using to start with. Steel and aluminum don't mix.

[@ryoung6730]

I hate to be negative , I came here expecting to see someone explaining how to weld aluminum,,cheaply. However what i'm seeing only qualifies as soldering . He didn't close the gap before he started, and he isn't heating the parent metal to the melting poing, so not braising,,just soldering a joint to fill it in,, nothing structural would last with this method.

[@firefox71]

That turned out much better than I thought it would for cast aluminum. Well done

[@firefox71]

@@jpsholland yeah, it won't pass inspection, but it is functional for his needs

[@IngridCastro-pu2xo]

Todos son fundidos

[@thomassullivan1676]

Magnesium mix

[@RMS-gl6wl]

​@@jpshollandwhy? Those castings are dirty anyways. That's why a lot of people won't fool with them.😊

[@ЕвгенийБережной-с7э]

Какие проволоки применяет не говорится все молча

[@ИгорьНедбайло-л6о]

Диву даёшься! Наверно Индия! Аргона и всяких плюшек, станков и т.п. нет, А Сварка есть. Значит можно,если нужно! Лайк!

[@Александр159-п4ф]

это не сварка на видео,а пайка алюминия специальными прутками по алюминию.

[@pg894]

потому, что это не сварка, а обычная пайка

[@Rom-Zecs]

@@pg894 а какая разница, сплав присадки близок к сплаву детали, деталь плавится, значит сварка.

[@pg894]

@@Rom-Zecs деталь не плавится, плавится пруток. разница на самом деле огромная

[@MrMoto948]

I was taught to heat the material up to 700C then let the rod melt into the weld. The alloy melting temp is 1200C. The melted rod will then adhere to the alloy on a molecular level providing a good, strong bond. What he shows is equivalent to spak filler. Not all rods are born equal and youtube Project Farm has tested 3 alum rod brands that work.

[@needmoreboost6369]

1200c? He makes his own rods from recycled cast aluminium it’s not diy solder

[@АндрейКрасюков-я8щ]

Ну это не сварка, это пайка. Знаю, потому что покупал подобные припои и пробовал с помощью газокислородной горелки делать подобное...но стоимость этих припоев и соответственно прочность шва... лучше тогда купить электрод шведский по алюминию и заварить без проблем. А если действительно хотите чуть ли не даром, то угольный электрод от солевой батарейки, сварочный инвертор, флюс для алюминия " Харрис" и вперёд...

[@robertpatterson3406]

how can you preheat Alum. to 700c when that would be 1292f and the melting point of Alum is 1220f.

[@MrMoto948]

Swedish aluminum electrode? You have my interest. Have you a link please? Thx.

[@marshallwilliams4054]

It’s probably super common alloy casting. Maybe a356. You should preheat it but you should not heat it above 450C. And you have to stress relief after a weld repair like this. Maybe heat to 320C, hold for 30 minutes and then ramp down 30° per hour for three hours. Then remove from the oven and allow to cool in ambient temperature.

[@pierrelombaard820]

A welder once used arc welding for a enjin topcover for me It was perfect

[@freefree3467]

После такого глобального перегрева детали, её повести должно, думаю что посадочные отверстия могут не сойтись.

[@maximmaxim7857]

Судя по мастеру,он потом эти отверстия либо рассверлит большим диаметром либо молотком вколотит болты. Перегрев детали? Неее. Не слышал🤣

[@BobahukBobahuk]

Это не коленвал а обычная крышка картера, нечего не будет

[@alec-s]

I weld alluminium via Tig usually, i'm going to try flame as well. I'm figuring out you need a very reducing flame and the iron rod is used to mix the melted joint ....

[@CLOClayton]

The iron rod is used to swirl the base metal and filler?

[@AJ........]

I think the iron rod is to get out impurities. I think that's why you hear him always tapping, I think it's to flick impurities off the rod so he can melt some more and pull out more impurities with a freshly flicked and clean rod lol

[@mel-3622]

That's a aluminium MMA stick rod not a iron rod. The flux is what helps lift the impurities to the surface, in TIG it the negative half waves adjustment that lifts them. I was a multi coded welder. A certified MPI inspector and a mechanical and electrical engineer. And a partridge gin a pear tree

[@alec-s]

@@mel-3622 Sorry man for MMA you mean SMAW AWS welding? If It Is so, this Rod should be used with arc welding, not oxyflame... I am a welder too and i know alluminium oxide melts at 2070°c while alluminium approx 700°c , i think he Is mechanically breaking alluminium oxide on the surface to heat the alluminium and protecting it with a reducing flame.... There are two rods , one of steel to mix and break oxyde and the other is a tig filling rod to fill in some alluminium in that joint

[@francescomereu682]

hello, but the electrode that you use and for aluminum ? How many degrees does the electrode you are using melt? I wanted to know if I can repair a scooter radiator with an electrode or can I try with durafix type rods? Thank you

[@emmamay2272]

He wasn't using the rod as filler. He was using it to get nice and hot, and mix the base metal under the dross, flicking it off. Once he had it hot and 'melded', he came in with some filler aluminum. You'll notice he went back and forth, removing the oxide layer with the electrode first.

[@lorenzoghinelli7018]

Man, if you see a flame not shaped and rough like that it means that you torch’s tip has to be replaced! ;) And by the way: this way of welding alluminum has not mechanical strength!

[@stevehaynes2857]

The part he has welded does not need mechanical strength, it is a container.

[@feitan8745]

@@stevehaynes2857 just use that super glue mix then.

[@justincase1575]

How do you think that aluminum was welded before mig and tig? I’ve oxy-acetylene welded aluminum on motorcycle transmission cases and it worked fine. I guess most critics are not old enough!

[@justincase1575]

By the way. I’m a retired certified welder.

[@stevehaynes2857]

I am a retired metallurgical scientist. We are on the same page here.

[@garyyorke1080]

Well I guess as it's only a cover a full strength weld is not required, however I'm not so sure just giving it a quick brush covers the fact it should be spotlessly clean before attempting to weld or in this case solder a huge chunk of material over a split .

[@cornwallav8r]

Cheap and Fast, not Perfect and Super Strong. It's a dust cap basically. Bravo.

[@Alec_Bike]

Good job man , i'm a time traveller and a blacksmith from 1350 and i never saw a such beautiful welding. Where do you install it on your horse... what happened ?

[@Miwka2TMagic]

Tig сварщик вышел из чата :-) Глазам больно.

[@clixsoft]

Ацетиленовый пост стоит дороже тиг сварки... это не быстро и не дешево, да и газосварщиком стать еще надо.

[@ardaongun8486]

👍

[@Володявв-л8ф]

@@clixsoft ацетилен стоит совсем недорого, карбид - по 60р/кг - это международная цена на такую небольшую работу вполне хватит полкило - даже с продувкой то что у нас ломят втрое цену - не имеет отношения к цене на международных биржах

[@pg894]

@@clixsoft горелка с двумя баллонами стоит дороже чем тиг, умеющий варить алюминий? Вот это новости.

[@Sery4Welder]

Видел я газовую сварку алюминия. Сам сварщик. Свариваю алюминий каждый день. Знаю как это делается. Как то не так 😏подготовка "на высоте "🤣🤣🤣🤣про монолитность шва и отсутствие дефектов можно забыть вовсе. А так то есть электроды для ММА сварки по алюминия, есть миг сварка при помощи полуавтомата))) что быстрее и по итогам дешевле этого творчества... Про тиг на переменном токе вообще молчу. Это по-умолчанию приоритетный тип сварки в ремонтных мастерских... ( без кузовного ремонта)

[@nikleo67]

Не иначе как Пакистан, край изобретателей из г-на и палок. До чего находчивый народ на фоне нищеты.

[@Прохожий-м6ч]

Сергеич,петля от стилалки сломалась,вроде силумин..реально спаять или что? Медяшки я много паял..

[@ДровосекДровосек-л8щ]

В середине 80-х варил поддоны от лодочного мотора "Вихрь" точно таким же способом. Флюса или аргона и близко не было. Но поддоны работали, где-то и по сей день один валяется в гараже.

[@kylesyx8432]

It’s just a housing, it not under a load ! ✌️but your still right !

[@nelute5]

Flacăra nu e uniformă la becul de sudură, deci are zgură pe interior. Trebuie curățat din când în când ca flacăra să fie ascuțită, pentru a concentra temperatura la vârf. Nu înlocuit, ci curățat ! Meseriaș e cel care repară, nu cel ce înlocuiește cu ceva nou ! Pentru eficiență și mai mare, mai ales la sudarea cu GPL (vezi filmul meu, unde modific becul de acetilenă și merg cu GPL care e de 20 de ori mai ieftin) se găurește capul de cupru , de la interior către exterior, cu un burghiu conic, pentru a face gaura conică și să concentreze temperatura în vârful flăcării. Poți înlocui materialul pregătit din alte piese, cu electrozi înveliți din aluminiu. Pasta de pe ei asigură o decapare perfectă, și nu mai e nevoie de electrodul de oțel pentru a sparge oxidul. Bravo, orice-ar spune „specialiștii” , eu te felicit și fă treabă în continuare ! Numai cine nu poate spune că nu ține ! E foarte greu si trebuie să ai mână și experiență, pentru a nu topi toată piesa, în loc s-o sudezi !

[@dijaya.mc.48]

Please send your link 🙏

[@PidokJacob]

Since Indonesia and the Philippines are like one race, bara-bara na lang bai hangang mabutas!

[@Заправду-м3д]

Это жесть. С таким сварщиком врагов не надо.

[@user-8windofchange]

Пакистан текнолоджиз😂!

[@pacopacome7511]

EXACTO!!..

[@ДмитрийКиселев-к6н]

Он штукатур

[@Admiral335.]

Так это же пайка, сваркой даже пахнет

[@Володявв-л8ф]

поэтому кому не нравится - идут и покупают новую деталь. за доллары ну или новый мотоцикл, что не так уж редко

[@carloslopezguevara825]

Y q electrodo estas usando y que tipo de soplete es? Ósea que gas usas en el soplete

[@TheOneAndOnlySame]

torch is good old oxyacetylene , he uses a steel electrode only as a pick to chase away the impurities and the filler aluminium is one he casts himself using scrap aluminium that he melts onto ridges on some make shift mold. You can see all this process in various videos from india and pakistan That's how they do it in this part of the world.

[@vovaserov1019]

Это не сварка, это пайка алюминия, припой типа А5 или зарубежный аналог кастолин, кабельщики и холодильщики пользуются подобной технологией пайки алюминия с 60х-70х годов, а мастер конечно Красавчик, руки из плеч, результат впечатляет, дороговато конешно 1 пруток кастолина в нашем регионе 750р. деревянных + пропан 1350р. 50литровый балон+кислород 1200р. Отсюда и ценник за такую работу конский, помоемому берут 500р. за сантиметр

[@LFESN]

Если кромки соединяемого металла плавятся это по любому НЕ пайка. Иначе отличить пайку от сварки станет не возможным

[@Вячеслав-т9с9з]

Совершенно верно! )) Это пайка , наложение припоя на поверхность металла ... Сам холодильщик))

[@Philip_Morris_666]

Не разу не паял алюминий, но мне что то кажется он паял оловом

[@Вячеслав-т9с9з]

Не , это припой по влюминию...Паял в 90-х годах оловом испарители алюминиевые ... Оловом чтобы паять нужна ещё железная стружка , чтобы разрушать оксидную плёнку....Алюминий поэтому тяжело паяется из-за оксидной плёнки...

[@vovaserov1019]

@@Вячеслав-т9с9зпару лет назад сам понял радиатор мотоцикла сузуки (знакомый просил), понял автогеном пропановой горелкой, припой А5, зачистил железной щёткой, затем грел радиатор и втирал как-бы этот припой, получилось неплохо, до сих пор катается.

[@martinnorbeck4657]

Mig with spool gun works too. I have used aluminum electrodes with a stick welder. The metal has to be about 1/8 minimum. The thinner the faster you have to go.

[@grancitodos7318]

I have welded broken outboard skegs back on, and extensions for worn ones, with stick. They disappear fast so you have to feed it in fast and move fast along the join.

[@TheOneAndOnlySame]

Do you realize that this man in the video lives in a place where the yearly salary is your week's salary? Do you think they have MIGS with spoolguns and easy access argon lying around? They work like this out of necessity and because they don't have access to fancy thousands dollar equipment. I'm not trying to be rude, but get a clue man

[@КамилСайфутдинов-н2о]

In order to restore the part qualitatively, it is necessary to eliminate the gap in the crack by tightening the crack with a clamp.😉

[@sJs78]

Mate, qualitatively , thats the first time ive ever seen this word used... wouldn't quality have done.?

[@dmoore0079]

Aside from avoiding potential weld defects, clamping would ensure that the part fitment should be the same (or close enough) after repair.

[@ФреддиКрюгер-й1н]

Надежнее синей изоленты ничего нет

[@правдорубстар]

@@ФреддиКрюгер-й1н на большое ума не хватило ?

[@sfvp9412]

@@ФреддиКрюгер-й1н le tenemos más confianza a la vini tape negra japonesa. Revienta cuando quieres que reviente y se estira siempre lo suficiente que presisas en especial en el verano.

[@elmerfudd835]

Do you fill it up with water to verify no leaks or can you fill it with water to check for leaks or should you use oil?

[@Simon_Jakle__almost_real_name]

I heard thin plates are trickier to wield. Would you chop aluminium with a chisel instead of using a tool that soon would be filled with the material?

[@Warp_Vital]

Кстати я так делал ещё до просмотра видео действительно способ хорош даже могу посоветовать👍

[@cuperr-wp9yz8il3m]

Лучше я буду не уметь, чем так уметь.

[@ІгорДяченко-и8и]

Горячий газ водоростей,, и да все прекрасно верится, применение в судостроении, газ водород очень опасньій. По етому такая сварка применяется на предприятиях имеющих установки по производству водорода.

[@jamalahmad8282]

لم اعرف نوع او رقم السلك المستخدم في البدايه نرجو الاجابه شكرا للعمل الجيد

[@paulkurilecz4209]

Pretty amazing as what he accomplished. I hope in the future that he will clean the part first. I can't resist, what is the AWS specification for his filler rod? 🙂

[@silverdr]

My guess is that's a brazing rod

[@paulkurilecz4209]

@@silverdr Actually, he is welding it. He makes his own filler rods. He has a video that shows how he makes them.

[@silverdr]

@@paulkurilecz4209 TNX. Colour me impressed then. I thought he was in fact brazing it…

[@paulkurilecz4209]

@@silverdr yvw. The one rod that looks like a regular welding rod is being used to remove the dross from the weld area. Most people aren't aware that you can used oa to weld aluminum. He is using a strong carburizing flame and this is providing the inert atmosphere for the weld puddle.

[@silverdr]

@@paulkurilecz4209 Yeah, that one looks like regular and is used only for mechanical help as it doesn't melt at those temperatures. That "strong carburising flame" is interesting though. Do you mean he uses less oxygen for the mix?

[@lodwill4007]

I stick welded a riding lawnmower blade mounting bracket. On two blade mower. I’m bad at cleaning. But I got the new aluminum rod hot. Enough. I goobered it up. And kept grinding cuts with. Dirty grinder wheel. Lol. But I penetrated good enough. Old man whent strait back to rock pile I told him not to. It held. Lol lol lol. The the more high tec welds . Like bike frame . I would clean more and get gas shield blowing on it. Or more flux. Good enough job.

[@TheOneAndOnlySame]

Respect. A good work with old technique

[@Öfarukyetmez]

Birçoğu alüminyum kaynağı yapmayı bilmiyor deyip alüminyum kaynağı yapamayan usta sana selam olsun. Alüminyum kaynağını oksi-asetilen kaynağı ile yapılmaz. Yapmaya kalkarsanız ancak sizin yaptığınız gibi olur. Alüminyum kaynağı AC akım veren TIG kaynağı ile yapılmalı. En sağlam dikişi AC akım akım altında TIG kaynağı ile elde edersiniz.

[@wemcal]

Great video.. sometimes you have to use what’s available and do the best you can with what you have.. great video

[@Aldijayamotors]

Mohon maaf , apa jenis elektroda yang anda gunakan pak 🙏

[@patmawati622]

om Itu pake borak atau ngga ya supya Gampang nyatu 🙏🏻🙏🏻

[@Doug.the.welder-hj6cq]

Love all the criticism in the comments, Arguing structural integrity. Looks like a cover of some sort. I don't believe it's going to be under much stress. Does the job

[@SlammingEDdog]

The guy is a ACE you can tell good job 👍👌👏👏

[@corsario6668]

La tecnica es curiosa , el problema que veo yo es que la deformacion de esa carcasa al calentarla provocara una deformacion en los planos que ya no acoplara correctamente ni al motor ni el eje del ciguenal. pero como concepto esta bien. un saludo

[@TheOneAndOnlySame]

Oh I'm sure those people don't know what they're doing. 🤦‍‍ Get a clue This guy must have repaired hundreds of such pieces. Go an watch more videos of aluminium welding in pakistan and india , you'll see they make do with ancient equipment. And it deservers respect since in the end, ,it works

[@marktirabassi7160]

Hey what kind of rid are you using there?

[@cesarburgoscuellar5285]

Pues no entiendo mucho de esto pero creo q la pieza debería ser ajustada para q las grietas curren y soldar para q está no quede descuadrada

[@manuelantoniovargas2121]

Eso ya es otra cosa Aquí solo enseñan a soldar

[@АлександрМаксимов-е4ц6е]

А это сварка ---- учили ещё 1972-м так можно . Сварка -= это не менее 85 процентов от прочности основного металла . . Трубку так сможешь сварить -= герметично . у тебя поры в металле - флюс добавляй -= хоть соду из хозмага . С уважением.

[@harleymain6767]

Hangi elektrotu kullanıyorsun ???

[@eddylorenzo5033]

I would have squeezed that case together to fill in crack then grinded a bit to have really clean metal

[@johnshelton1058]

How too make it work for two days.. follow these tips and examples... lmao. Good luck brother. Your gonna need it.

[@juliomarcelinovillalva777]

Con que varilla está aportando material ? Gracias.

[@alanamarina7089]

Na verdade ficou bem feito o serviço parabéns sorriso mt Brasil

[@yackzork]

dont listen to these non welding city boy comments ..like grandpa told me sum men see a fire fly and call their self a welder u sir done helluva job

[@ВладимирМаклаков-ш2ж]

Привет, какой газ ты используешь?

[@milosmilanko4472]

what material are you adding ???

[@cesurozturk6753]

It makes much more sense to use the propane gas you have to melt aluminum. Can make sand mold using old part. Aluminum casting is definitely easier and longer lasting.

[@Abraham-q5p]

Todo esta bien, nomas hay que ver que la pieza no se deforme con el calor .

[@talitacecilia2689]

O serviço ficou lindo, aparência muito boa. Gostaria de saber sobre a funcionalidade da peça recuperada. Fechou direitinho, houve vazamento? Essas peças costumam deformar com muita facilidade.

[@arccraft8583]

If weld properly,its wont leak and deform,in the video u can see he using,stick rod to remove the oxidation layer after he welded,so the pure aluminum will remain fused..and yes,this is the cheapest way to do the engine cover repair..

[@Huynhvanvien007]

Đã đăng ký kênh rồi bạn ơi 😊

[@andygoldensixties4201]

it's just a lid, a cover with a crack that does not seem to have the purpose to hold a great mechanical stress, so, that quick fix in this case (only) is good enough if you don't want to buy a spare part

[@billpickelheimer6323]

Seems that many don't know how to clean the part that needs welded and the tip that needs cleaned severely, nothing like passing along bad habits

[@gokilchannel6485]

wow..sangat menabjubkan..💋❤💯💫👍👍👍🙏..

[@赤白ピンク]

少し数字的なこと質問しても良いですか、母材の温度はどのぐらいですか、また溶棒の種類は何ですか、本体強度はどのぐらい戻りますか・・・ 知りたいことたくさんありますガス溶接でしょうが、アセ、と酸素の割合、圧力等・・・

[@MetinTetiker]

Doğru bir uygulama yapıldığını gördük.El ustalığı bu gibi kaynak ,şlemlerinde en önemli olandır.Ayrıca malzeme alaşımına göre elektrot seçimi olmazsa olmazıdır.Uygun elektrot olmadığında kaynak yapılan parça eloksala girdiğinde kaynak yerinde uyumsuzluk(Siyah oksit) ortaya çıkar.Geçmişte bu işlemleri büyük bir yerleşim yerinde tek başına cevap veren kaynak ustamızdan sonuçlarıyla görmüş biri olarak söylüyorum.Şöyleki bir alüminyum profili bu tarz kaynak işleminden sonra tesviye edip eloksal boyaya tabi tutulduğunda temiz görüntü alınırsa elektrot seçimi doğrudur.Yok kötü görüntü gri ayrı siyah ayrı belirmiş ise elektrot uygun değildir.Alüğminyum döküm alaşımlar alüminyum ince tellerle de bu şekilde kaynak yapılır.İhtiyaca cevap verir.Sizi ell melekeniz güzel çalışmanız adına tebrik ediyoruz.

[@reco35reco]

Yerinde bir tespit, selamlar Düsseldorf,dan

[@MetinTetiker]

@@reco35reco Bizdende selam olsun.

[@peraspera6559]

Удивительно много людей, оказывается, понимает в ацетиленовой сварке,хотя в последнее время она практически вымерла. В 2000 году варил много и уверенно, наконечники горелок гнул и ковал сам из медной трубки...

[@АлексейБуц-ж2с]

Та,вообще сварщиков небудет скоро,как кузнецов,столяров,токарей,фрезеровщиков!

[@Прохожий-м6ч]

А каким припоем он паяет,не знаете?

[@Димонстр-й5в]

А ты не вкурсе, что есть электроды для ручной сварки, которые варят аллюминий?

[@janjanboquia6738]

wat rod you used as filler metal?

[@joefregoso2725]

Muy bien, un saludo

[@ariari732]

Head cb 100 punya Saya mengalami bocor bagian dudukan noken as sebelah busi bisa gak ya di las 🙏🏻🙏🏻

[@АлексейБосх]

Умники как всегда,то не так эдак,70-90-е так и варили поливные трубы, на жигулях часто варили масленный всасывающий?как назывался?

[@Александр159-п4ф]

на видео не сварка,а пайка кастолиновыми прутками для пайки алюминия.

[@victormedina177]

Muy informativo, muchas gracias. Ahora SI sabemos cómo soldar aluminio

[@manuelantoniovargas2121]

Una cosa es ver y creer y otra es la realidad La práctica hace al maestro

[@naylaofficial8527]

Itu kawat las nya ada 2 jenis ... apa saja kawat las nya kak. Terimakasih video nya sangat bermanfaat buat saya.

[@febrikitink3690]

Tak kiro mau di las listrik mas., Jebule las karbit 😁

[@СергейВасильев-е2ь]

Для неответственных деталей, такой вариант возможен. Здесь грубая сварка, коробление металла. Для чистоты сварки алюминия нужен другой вид сварки алюминия

[@ВагифВагиф-о5н]

Это не сварка.

[@ИванЗаказчиков-ф2и]

Я не специалист, но вроде и автор видео и вы путаете сварку и пайку, если в руке есть припой то это пайка, а сварка это когда без него, не так разве?)))

[@BillyBob-uc9zp]

Well done Mr 😎

[@Rock-bottom-78]

That looks to be a magneto cover, of a small motorbike engine, that weld wouldd be plenty sufficient

[@AABOU331]

يبدوا انك من الكثيرين الذين لا يعلمون كيف يلحم الألومنيوم. 🤔 أين تنظيف القطعة وإعادة الشق إلى مكانه ثم الحم القطعة بدرجة حرارة لا تفوق 700 °c

[@tylertinney2095]

A clean tip helps with the heating

[@noutubepientue]

Itu pakai kawat las apa bang..mohon info nya bang.

[@فهمىابودهب]

راءع ولحام جميل جدا جدا هل تستخدم مساعد لحام

[@D-rizzy31]

as soon as the torch got lit with a lighter I knew I was on the wrong channel.

[@jamesabbott7469]

A great job! Would like to know what kind of rods you used because that seems the key to success! please share thank you,!

[@Nilme07]

Hey Bud, did he tell you what kind of rods he is using in the video? Cheers 🙏

[@jamesabbott7469]

@@Nilme07 no! not yet!

[@andyroo3022]

He uses the electrode (flux covered) rod just to push and mix the metal. The alumium he uses looks like recycled stuff. Better to use a quality aluminium welding rod. All alumiium welding rods are not the same.

[@КоттоДобрый]

У сварщиков аргонно дуговой сварки кровь пошла из глаз, и у меня тоже)))

[@rassvet7770]

Я то думал нахера TIG/MIG дорогущий-газовая горелка и желание.

[@ДжимНоговицын-х6и]

Нужна только дефицитнейшая и наверно дорогущая порошок присадка АФ4С кажется называлась.

[@user-gl7lf6zh2e]

Похоже на пайку кастолином

[@digma713]

Это имитация бурной деятельности. Зачистить лепестком , стянуть плотно трещины для сохранения размеров и геометрии и качество напаяной коросты , ВСЁ под большим вопросом. ПОНИМАШ.

[@СергейМангушев-я4в]

Дичь полнейшая, только аргон. Электродом для алюминия и то лучше было заварить.

[@MUHAMMADAMIN-gy5mk]

Dang.. Gareem...🤗🤗 from Kudus

[@scorpionyad]

Аргонове зварювання алюмінію стоїть в стороні і нервово курить від таких спеців ! :-)))

[@FabioTitoMontefinale]

Muy bueno☺👌👍

[@zaord]

Quel diamètre de buse utilises tu ?

[@JenaroCandido-gw6df]

Que tipo de soldadura utilizo amigo

[@MuhammadSaleem-g4s]

Is aliminium welding rod and macheen is not avail able whay gas torch used

[@ИванБырамыда]

Технологии СССР в Юном технике в журнале 1974 года мы так варили алюминий!

[@ostinsanchez9906]

Ahora as un video como desolda el aluminio ya que la tapa no coincide, ya que no serraste la grieta devesti apretar con la prensa.

[@НиколайДанник]

Напряг с метала не снял,а это значит что изделие повело и вы его просто заслюнили. Даже фаску не выбрали. А в целом способ рабочий.

[@user-8windofchange]

От лютой безысходности.

[@philliptaylor8270]

This looks like it takes a fair bit of practice to achieve a good result.

[@gjkozy]

What rod did you use?

[@nyankorunaway2446]

うまいこと考えたな。アルミを溶かして、溶接棒は均しに使ってるのかな。素人だとちょっと難しそう。 I'm surprised for your skill, but it may be difficult for me as a beginner. from JP^^/

[@wanderleyfernandespassos-fb8se]

Boa dica! ''Ecelente''gostei.

[@AutodidactEngineer]

This process is called brazing not welding!

[@bovanbang-pp3xu]

Many know this is brazing, not welding. big difference in strength.

[@pandawaaluminium]

Cara las aluminium makasih ilmunya mas.salam dari pandawa aluminium

[@ToniAgoglia]

Che tipo di elettrodo usi?

[@moiseszanela1735]

Existe vareta de solda própria para antimônio 😉 desde 1987.

[@debemcomavida5741]

fazendo dessa forma que ele fez é muito melhor, comprei varias varetas que não dão liga, fiz dessa forma do video e deu muito certo.😉

[@manobc1723]

Também já comprei mas só consegui esquentando a peça

[@robertmencl9169]

There is so much more to welding, than simply melting the rod.

[@jpsholland]

How many real welders are on this world? Most of them are even low level production MIG "gluers". Not much of a miracle most people halelujaing over this kind of videos. If this was so good and fast and cheap and high end, then why would the industry use all that expensive TIG stuf? People believe what they see. This is my 2 cents, from which he get 1 cent. For the poor countries this kind of fantasy tech science is a good income.

[@treyleitzell7185]

What kind of rod is that ?

[@reycatindoy7202]

What type of rod is that

[@arikmate]

Keren bang channelnya banyak yv liat dari luar Indonesia.. Kok bs bang

[@КомилжонМажидов-щ7ц]

Горелка ацетилен биланми.сим оддий алюминми илтимос ёзинг