L1800 DTF - Capping Station ink Pad/Weekly Cleaning/Not a Pro/Just Sharing :)

[@yourunclesam6780]

The string through the spring hole ! gREAT IDEA. tHAT WAS EasY FOR ME.tHANK YOU

[@allypeyton]

Thank you!! The string through the spring hole saved me.

[@jesusarellano3737]

Hello is it ok if my l805 doesn’t have the foam on the capping station? Do I need one ?

[@MRSGulmayo]

yes, it provides cleaning and priming, and prevents drying of ink within the printhead :)

[@jesusarellano3737]

Oh ok thanx I will have to order one

[@jesusarellano3737]

@@MRSGulmayomines doesn’t have that spring how else kan I remove it ?

[@IzwanRahman]

terima kasih ide bebenang sebelum pasang spring. membantu

[@jcmoney11111]

Good video, I recently purchased a L1800 from Pro-Colored and they shipped it without a piece of foam in the capping station and I just recently noticed when I was going to wet cap because I was already having some nozzle issues. Is this something that companies are doing now or was this a complete mistake? I assume you can't really wet cap a station unless you have a piece of foam to hold some capping solution against the printhead. Is there any way to get that little great off of without destroying it to put a piece of foam in?

[@rewdroid]

Hi, thanks for the instructions! Unfortunately, when I clean the head, the bubbles come back in the station :(. I tried flushing the two small tubes with cleaning fluid, but it can only flush them now with the left one, not the right one. Is that supposed to be the case? Thank you

[@sherylshahan5593]

Did you ever find this answer? I'm having the same problem

[@rewdroid]

@@sherylshahan5593 Yes, the cause was sediment in the tubing under the Capping Station. I disassembled the whole thing and pulled the sediment out. I recommend a regular hand flush with at least distilled water.

[@sherylshahan5593]

Thank you!

[@angellae.1327]

How do I put the capping station ink pad back on? Having a hard time connecting the two lines/tubes back to it.

[@MRSGulmayo]

just use your to finger to hold the tube, or you can use curv twizzer also

[@angellae.1327]

@@MRSGulmayo thank you for your response. Are the tubes really that short or am I able to pull them out/up more to make it easier to attach back to the ink pad part?

[@MRSGulmayo]

@@angellae.1327 yes the tube is short just slightly pull it and be careful with the inkpad

[@alexn.5814]

Hi, I accidentally removed the steel net and cannot plug it back. Will it be a big problem?

[@MRSGulmayo]

maybe you need to buy new capping station ink pad, and be careful to clean it next time:)

[@alexn.5814]

@@MRSGulmayo Thanks so much for replying

[@MRSGulmayo]

@@alexn.5814 your welcome my friend, Godbless =)

[@AH-qh9qi]

Hi sir, pleas help My epson1800 Does't print, it just keep the red lights blinking and when i reset it it releas the wast ink out of printer and the red light blinking again and agian. I clean the head but still the same problem.

[@MRSGulmayo]

hi friend mesage me at my fb: maria rosario santiago gulmayo

[@VeniVidiVici444]

What happens if the ink gets congested and dries out on it?

[@MRSGulmayo]

it may cause blockage on the head

[@MRSGulmayo]

Transform your projects with stunning vector art illustrations! Explore creative gallery and elevate your visuals to the next level. Discover the power of bespoke designs. CHECK THE LINK ON THE DESCRIPTION BOX!

[@pydes127]

Thank you for the tutorial...

[@MRSGulmayo]

=)

[@punitmaurya01]

can you tell me wht is the roll of this ink pad in the printer

[@MRSGulmayo]

prevents the ink in the Print Head Nozzles from drying, protecting the Print Heads to keep them functional.

[@punitmaurya01]

@@MRSGulmayo actually my printer is not showing the colour properly and specific yellow colour

[@MRSGulmayo]

@@punitmaurya01 i'm not an expert, but maybe you need to clean, flushing or manual cleaning your printhead :)

[@kfg970]

i found my l1800 faded white, but when i clean the capping station, the white colour is coming good, but still inconsistent, but yeah it turn good everytime, is it normal to do like your video as a monthly routine ? is the capping station i mean the sponge need really good care ?

[@MRSGulmayo]

Yes my friend. Cleaning the capping station is important thing to keep it clog free. Maintenance should be at the end of its daily use =) kzbin.info/www/bejne/Y6W6e4qIl92lppY

[@lorenzolozano3569]

@@MRSGulmayo hello my friend after i clean the capping everyday why is still fading after the first print

[@lorenzolozano3569]

@@MRSGulmayo how long do you these method and how old is your printer now thanks

[@MRSGulmayo]

hi friend, before you print, suck the white damper using syringe then run clean :)

[@MRSGulmayo]

@@lorenzolozano3569 better to use metal mesh damper base on my experience =)

[@MrPlomsone]

I lost the tiny spring. Do you think it is an issue?. Printhead barely prints and when I do head clean I barely see any ink going to the capping station and the external waste tank. Is it because the small spring is missing?

[@MRSGulmayo]

hi friend,yes you need to put back the spring :)

[@MrPlomsone]

@@MRSGulmayo Ok thank you for responding.

[@MRSGulmayo]

@@MrPlomsone ok my friend Thank You for visiting my channel please like and subscribe =)

[@waceembroidery2645]

did replacing the spring fix your problem? same issue here

[@MrPlomsone]

@@waceembroidery2645 I did buy a new spring and had to actually install a new print head. That was my main issue, which I didn’t realize at the time. Now it’s printing like new again.

[@BUdukkan]

thanks a lot....💯👌

[@graphx88]

Tuwing kelan dapat linisin lods?

[@MRSGulmayo]

wkly po ako

[@graphx88]

@@MRSGulmayo ilang years na po sayo yan lods ok parin ba till now?

[@MRSGulmayo]

@@graphx88 yes po goods na goods paden, mag 3years napo :)

[@niemarabalo1512]

Boss need your help. Bago pa ung head at damper ko. Naka 9 prints lang at d na nalabas ung white. Nag higop buga na din ako. Pero duda ko is ung capping nya is parang sira na ung foam. Posible ba un ung sanhi ng hindi paglabas ng white? At san po makakabili nung capping? Thank you.

[@MRSGulmayo]

hello po good day, pag nag clean ka boss humuhigop ba yung waste tank mo?

[@MRSGulmayo]

pag indi po my bara yunn tube mismo nun, yun po try nyo i suck baka barado po

[@MRSGulmayo]

kzbin.info/www/bejne/Y6W6e4qIl92lppY

[@niemarabalo1512]

Opo boss humihigop naman po sya pag nag hihigop buga ako.

[@MRSGulmayo]

naghigod kapo sa white damper boss?

[@itnas68]

hello po, pag konti nalang lumalabas sa waste tank kahit sa ink flushing posibleng palitin na po ink pump assembly? wala din po print out ok nmn po yung head nung binugahan ko ng cleaning solution.

[@MRSGulmayo]

hello po nag manual cleaning po ba kayu before mawalan ng printout?possiblenproblem po kasi pag ganun na short po ang head baka po may nabasa sa board.

[@itnas68]

@@MRSGulmayo opo, 2 p.head ko kahit isa walang print out at konti talaga yung nalabas na waste ink pag nag head cleaning ako.

[@MRSGulmayo]

@@itnas68 shorted po yung board nyo sir pag ganyan :(

[@MRSGulmayo]

@@itnas68 need napo palitan, nextyn po ingat nalang din sa pag manual clean at pag pabalik ng head, make sure po alisin nyo sa saksak yung powed cord, at alisin nyo po sa flex yung head para sure po lagi napakselan po kasi...

[@itnas68]

@@MRSGulmayo iningatan ko nmn po maam n di mabasa yung board and nakaunplugged nmn po pag balik ko ng head.

[@thedeazyteam]

thanks

[@qucuscase]

Busa di cappingnya sudah di modif ya mas?

[@MRSGulmayo]

Hi friend, Sorry but I don't understand your language =(

[@lorenzolozano3569]

BOSS TANONG lang ilang beses ka po nag cleanhead isang araw? pag ba sa first clean head mo hnd lumabas nag headclean ka ulit? after lumabas ng maganda color sakin boss nawawala na yung linaw ng white after first print

[@MRSGulmayo]

before ako mag print boss headclean muna ko lagi para mag suck mabuti white after nun ok na tuloy tuloy na, pero suggest ko boss mas maganda labas ng ink pag metal mesh damper gamit mo

[@MRSGulmayo]

palit kana po ng damper kung di maayus buga ng ink, ialng years o months napo yan?

[@lorenzolozano3569]

@@MRSGulmayo sigii boss salamat otw na yung metal mesh ko 1year nadin to sakin damper na stock pa nasiraan kasi ako head nakaraan

[@MRSGulmayo]

@@lorenzolozano3569 sige boss Godbless po =)

[@liliguarin2778]

ayos!thanks po =)