This is the most helpful video on DTF printers I have seen! Thank you!
@brildoren7440 Жыл бұрын
Thank you so much!
@rok17265 ай бұрын
the best video that covers it all ...tnx👌🏻
@KodiChristinaCalvertNaturalCha11 ай бұрын
This is a great video! do you have one on how to replace the ink dampers?
@sandrabarrera89467 ай бұрын
Hola muy buen video.. tengo una maquina dtf es la r2000 dx5 y tengo un problema cuando imprimo azul me salen unas lineas blancas horizontales pero solo en ese color y no entindo porque..
@johnmessenger7292 Жыл бұрын
awesome and informative video thanks a heap
@brildoren7440 Жыл бұрын
Thank you so much!
@تاوزنسوني2 ай бұрын
sorry my printer only print the midle line of the paper any one have a solution please ???
@tisprintcraftstv Жыл бұрын
Please I just bought an Epson L1800 to be converted to DTF printer but someone said it is not advisable as the printhead gets clogged easily. Kindly advise me further. Thanks
@nalyatenas5626 Жыл бұрын
hola quiero saber si tienen algun video que me ayude a solucionar , mi printer esta llegando solo a una parte del diseno y despues se detiene, tienes algun video , tengo un epson l 1800 dtf , gracias por tu ayuda
@jcevolutionprints128510 ай бұрын
My DTF blinking 2 red lights same time. It started by printing a few steps then stops. When i command again it does the same
@miss_xh Жыл бұрын
Hello, where did you get your printer driver for epson? The drivers I have don't show the advanced options like yours
@brildoren7440 Жыл бұрын
Hello! Sorry for the late response. You can download the drivers directly from EPSON here: www.epson.eu/en_EU/support/sc/epson-l1800/s/s1293
@nataki1192 жыл бұрын
Hello, thanks for the video. It is very helpful. I have an Epson L1800 roll model printer. When printing one image, the printer snatches the film back a little after the printing is done causing the design to smear. I don't know what's causing it to do that after it prints.
@brildoren74402 жыл бұрын
Hello! Thank you for watching. If you use Digital Factory DTF Edition you should increase the "Roll End Advance" option so that it pushes the film and does not cause the head to rub against the design. If you use other software, find a way to slightly stretch the design to avoid this problem.
@ibrahimhassan61642 ай бұрын
(DTF Printer r300 L1800) power button, ink drop, paper feed all buttons lights are flashing and head does not move,,
@whitewindows3052 Жыл бұрын
Good morning I have a new modified Epson L1800 for dtf but when i start printing there are small bubbles like foam rising from my wast ink pad to my print head. Then i have wast ink on my paper. Can you help me with this problem please
@krystalmoates7159 Жыл бұрын
Were you able to fix this? The same thing is happening with mine now.
@therenaldcruz Жыл бұрын
Hi, i have a problem with my magenta color, it has black color in it, all colors are okay except colors that needs magenta. Magenta damper has black on it so it was contaminated, so what i did is to replace my magenta damper but the issue is still the same, my magenta colors has black color mixed with it.
@brildoren7440 Жыл бұрын
Hi! I would suggest changing the damper first, but you should flush the printhead before replacing it. You should also clean the wiper blade and the capping station (the area where the printhead rests, which can be very dirty and, due to the negative pressure, the printhead absorbs discarded ink and contaminates the damper ink).
@tt94942 жыл бұрын
Hello, I have a question. There is a phenomenon that the speed drops in the middle of printing. I've replaced heads, reinstalled software, everything.
@brildoren74402 жыл бұрын
Hello! This may be because the usb ports are set to save power. You should disable the power saving options to ensure the flow of information. Another option could be a faulty usb cable. You can try on another PC to check if it is a printer or a PC fault. You can also contact Cadlink support and explain your problem. Hope this helps!
@tt94942 жыл бұрын
@@brildoren7440 thank you! ! i will try it.
@yourunclesam67802 жыл бұрын
very interesting tutorial. I think I need help, I have a L1800 printer gave me a problem, the head printer replaced it and now it doesn't print anything, I already did head cleaning, nuzzle check and nothing. Maybe main board problem. Can any good samaritan help me?
@brildoren74402 жыл бұрын
Hello! Has the printer shown any error? Have you flushed the print head after disassembling it to check if the cleaning liquid comes out? It's also really important to make sure the flex cable is in place. I recommend taking the ink out of the dampers with a syringe to check if it comes out properly. You should also verify that the transportation lock is not on. Finally, I recommend that you do an initial ink charging by resetting your printer. I really hope this helps!
@cherylbellers2852 жыл бұрын
My DTF EPSON L1800 will start printing well and then just stop laying down white. Sometimes I will get a full 13x19 film printed and when I start next sheet the white stops. Sometimes in the middle of printing the white just stops. Any suggestions?
@brildoren74402 жыл бұрын
Hello, Cheryl! There may be some solid residue in the dampers. So I would recommend replacing the white ones. Hope this works!
@jackyalcatras Жыл бұрын
Hello, updated from my last question. I have a new machine Epson SP1390. After printed 5 sheets of A3, suddenly the initialising getting slow. It took about 25minutes on the first initialising then pop up error. Tried reset the spooler but still doesn’t fix. Get more space on C drive but still problem. Any solution? Thank you.
@brildoren7440 Жыл бұрын
Hello Jacky! What software do you use to print? Have you tried uninstalling the drivers and reinstalling them? Have you tried changing the cable or the USB port?
@jackyalcatras Жыл бұрын
@@brildoren7440 Hi, thank you so much. I will try to change the epson sp1390 driver. Or maybe you have recommendation for that software? Give link please. Thank you.
@jackyalcatras2 жыл бұрын
Hello, very amazing video instruction. I have a problem with my dtf SP-1390. After I did a print head cleaning. The printer is just constantly nonstop doing head cleaning never stopping for hours. I turn off on again the same thing happens. waste so much ink. any solution for that? thank you.
@brildoren74402 жыл бұрын
Hello, Jacky. Thank you for your kind words! Have you installed the drivers correctly? What software are you using? If you can't get it sorted out, we recommend you contact your distributor in order to find a solution.
@jackyalcatras2 жыл бұрын
@@brildoren7440 acro9.03. Was very good till I did manual head cleaning. The printer just kept on doing head cleaning as some one do it by the system. Wasted so much ink.
@jackyalcatras2 жыл бұрын
@@brildoren7440 updated comment. After I unplug all the cable and USB. The print head stop moving but then unable to turn on the green light. Any solution? Thank you.
@creditrockzboyz1032 жыл бұрын
@@brildoren7440 Hello my printer don’t print yellow ink , can you tell me the problem ?
@brotherlybrand Жыл бұрын
Hello, every time I print black an orange showish/ or line appears to the left side of every part of the design that has black ink.
@brildoren7440 Жыл бұрын
Hello! You should clean the nozzles by disassembling the printhead and flushing. Then make sure to clean the area where the dampers rest so that there is no contamination between the inks. What software do you use? Depending on it, you may also have a problem with the ICC profile and that's why another ink appears when you print black.
@brotherlybrand Жыл бұрын
@@brildoren7440 Hello we use RIP PRO V1.17.0
@sushantkaushik96732 жыл бұрын
Hello , I have Epson L1800 which is converted to dtf few days back. I am facing issues with print. There is a separate wet area outside the print. It looks like stroke. On every print i am facing this issue . It is creating a white wet line without any colour. What to do?
@brildoren74402 жыл бұрын
Hello! Where does it appear? Is it at the end of the print? This is probably because the print head rubs against the film. Make sure your DTF film is completely horizontal and leave margins before and after printing to avoid this problem. Hope this helps!
@sushantkaushik96732 жыл бұрын
@@brildoren7440 it appears on border of print. Is this problem occur due to humidity? I wish I could upload image here
@hiroshikawai33002 жыл бұрын
I found your video superb! I wonder if you agree that I will copy your video and put my Japanese superimpose or after recording in Japanese language for re-uploading on to the You Tube for my Japanese clients. Please advise. Thank you for your consideration.
@brildoren74402 жыл бұрын
Hello Hiroshi! Thank you so much for your comment! I really appreciate it. As long as you reference or mention the original video, there should be no problem.
@hiroshikawai33002 жыл бұрын
@@brildoren7440 Thank you for your acceptance! I will try to localise or give the superimpose in Japanese language to introduce your video.
@tt9494 Жыл бұрын
I replaced it with a new head and no ink comes out. Is there any workaround? head cleaning It doesn't heal even after sleeping overnight.
@brildoren7440 Жыл бұрын
Hi! I suggest doing a power flush from the printer driver, if it doesn't work, you should make sure the dampers are full of ink. You can use a syringe. Finally, if none of this works, you should check if the flex cables are well-connected to make sure that liquid is coming out of the printhead by flushing it.
@tt9494 Жыл бұрын
@@brildoren7440 thank you for the advice. I continued cleaning, hypercleaning, but it didn't work. As a last resort, I stuck a syringe in the waste ink hose to remove the air. that solved it thank you.
@katherinequinonez86892 жыл бұрын
Donde encuentro el video original en español?
@brildoren74402 жыл бұрын
Hola, Katherine! Aquí tienes el link al vídeo original: kzbin.info/www/bejne/jaCrkImerqmairM
@peaceprotection61772 жыл бұрын
What type of printer is this in the video is it dtf?
@brildoren74402 жыл бұрын
Hello! Yes, we used the Epson L1800
@peaceprotection61772 жыл бұрын
How much for that printer
@creditrockzboyz1032 жыл бұрын
Hello
@brildoren74402 жыл бұрын
Hello! You wanted to ask us something?
@creditrockzboyz1032 жыл бұрын
@@brildoren7440 yes , my epson l1800 not printing yellow inks
@creditrockzboyz1032 жыл бұрын
What can I do
@mothmoiloa2 жыл бұрын
This printer is too much work😕
@brildoren74402 жыл бұрын
Hello Motheo, don't worry! This video is only for showing you how to solve the problems. Remember to keep your printer active and clean it every once in a while so you don't have any problems 😊
@user-gw3gz5sh2z9 ай бұрын
Prefer American no Asian heavy accent
@impressions5139 Жыл бұрын
Bonsoir excusez mais la sincèrement je m'arrache les cheveux, La couleur ok Mais pas de blanc. J'essaye votre maintenance et les clips des petits réservoir d encres refuses d entrer .du coup les petits réservoir ne sont plus dans leur alignement parfait
@brildoren7440 Жыл бұрын
Bonjour, ne vous inquiétez pas. C'est probablement parce que l'encre s'est solidifiée et c'est pour cela qu'ils ne rentrent pas. Je recommande de les remplacer et de nettoyer (flushing) la tête d'impression. J'espère que cela résoudra votre problème.
@any7513 Жыл бұрын
thanks for the video.) tell me please, did you use acrorip v10? The problem is that the white ink shifts towards the end of the image and part of the drawing remains without a white substrate. Especially if multiple image and single print job
@brildoren7440 Жыл бұрын
Thank you Any! We don't use acrorip v10 we use cadlink digital factory dtf edition but this is a white layer shrinkage problem. Maybe you have too many shrinkage pixels. You should go to the White tab and under Decrease set less pixels than you have. Maybe 1 or 2 pixels is enough.
@any7513 Жыл бұрын
@@brildoren7440 thanks a lot for the quick reply
@upseroare Жыл бұрын
your image is too tall. Reduce 1 cm.
@Beingcheilling478 Жыл бұрын
Why is there lady talking when the guy is talking?
@Beingcheilling478 Жыл бұрын
Very annoying and hard to listen too
@brildoren7440 Жыл бұрын
Hello Bryce. That's because the original video is in Spanish so what you can listen to is the English translation/voice over of it. If you only want to watch the original video, you should then go to Brildor's main channel.